If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Code P1133 on 2000 Saturn SL
Hi, this is also posted to rec.autos.makers.saturn
I have a 2000 Saturn SL with a high idle problem and a constantly lit 'check engine light'. It only does the high idle intermitantly, when the engine is warmed up. Sitting at a stop light, while in neutral, the RPM may shoot up to 2000+. It will idle correctly, at around 800 RPM or so, after shutting the engine off, then restarting it. Since the 'check engine soon' light is on, I took it to Advance Auto and had them do an OBDII scan on the PCM. The code returned was: P1133 Manfacurer Contrl. Fuel Air Metering (those are not typos, that's what it spit out) My Haynes manual doesn't say anything about P1133, but a Google search for P1133 comes up with: P1133 HO2S Insufficient Switching Bank 1 Sensor 1 This short message thread, http://tinyurl.com/5zps9 talks about the sensor and some of the conditions that may cause P1133 to be set. Thanks in advance Ed |
Ads |
#2
|
|||
|
|||
Possible Causes of a P1133 on this vehicle (verbatum from ALLDATA):
An intermittent connection or corrosion in the O2S-1 harness connector can set this DTC. Use scan tool to monitor O2S-1 voltage with engine running at normal operating temperature while wiggling the signal and ground. Make sure the sensor is tight. The most probable cause for DTC P1133 is contamination. Check for obvious contamitation (oil, fuel or engine coolant) by removing sensor. Identify and correct the cause of the contamination if contaminated. Replace the O2S-1. "Edward Crismond" > wrote in message ... > Hi, this is also posted to rec.autos.makers.saturn > > I have a 2000 Saturn SL with a high idle problem and a constantly lit > 'check engine light'. It only does the high idle intermitantly, when the > engine is warmed up. Sitting at a stop light, while in neutral, the RPM > may shoot up to 2000+. It will idle correctly, at around 800 RPM or so, > after shutting the engine off, then restarting it. > > Since the 'check engine soon' light is on, I took it to Advance > Auto and had them do an OBDII scan on the PCM. The code returned was: > > P1133 > Manfacurer Contrl. > Fuel Air Metering > > (those are not typos, that's what it spit out) > > My Haynes manual doesn't say anything about P1133, but a Google > search for P1133 comes up with: > > P1133 HO2S Insufficient Switching Bank 1 Sensor 1 > > This short message thread, http://tinyurl.com/5zps9 talks about the sensor > and some of the conditions that may cause P1133 to be set. > > Thanks in advance > Ed |
#3
|
|||
|
|||
Steve Mackie wrote:
> Possible Causes of a P1133 on this vehicle (verbatum from ALLDATA): > > An intermittent connection or corrosion in the O2S-1 harness connector can > set this DTC. Use scan tool to monitor O2S-1 voltage with engine running at > normal operating temperature while wiggling the signal and ground. Make sure > the sensor is tight. > The most probable cause for DTC P1133 is contamination. Check for obvious > contamitation (oil, fuel or engine coolant) by removing sensor. Identify and > correct the cause of the contamination if contaminated. Replace the O2S-1. > Thanks Steve for your time and effort. I've entered this into my notes. Ed |
#4
|
|||
|
|||
On Wed, 02 Feb 2005 18:15:55 -0500, Edward Crismond
> wrote: >Hi, this is also posted to rec.autos.makers.saturn > >I have a 2000 Saturn SL with a high idle problem and a constantly lit=20 >'check engine light'. It only does the high idle intermitantly, when the= =20 >engine is warmed up. Sitting at a stop light, while in neutral, the RPM=20 >may shoot up to 2000+. It will idle correctly, at around 800 RPM or so,=20 >after shutting the engine off, then restarting it. > >Since the 'check engine soon' light is on, I took it to Advance >Auto and had them do an OBDII scan on the PCM. The code returned was: > > P1133 > Manfacurer Contrl. > Fuel Air Metering =46rom the FSM: DTC P1133 The oxygen sensor 1 (O2S-1) is an electrical source that responds to oxygen content in the exhaust manifold. When the sensor reaches approximately 316=B0C (600=B0F), it produces a voltage based on the difference in oxygen between the atmosphere and exhaust gas. The powertrain control module (PCM) sends a bias voltage, 391-491 mV on the signal line which is pulled up through high resistance. When the O2S-1 is cold, it produces no voltage and has extremely high internal resistance. The internal resistance of the sensor is much greater than the resistance of the bias pull-up resistor. However, when the sensor heats up, it produces voltage that overrides the bias voltage. This voltage is read by the PCM to determine a rich/lean O2S-1 signal used to adjust injector pulse width. Under normal conditions, low sensor voltage means high oxygen content/lean air-fuel mixture and vice versa. Normal sensor readings will fluctuate between 10-999 mV. DTC P1133 sets when the O2S-1 signal has too few switches over a certain length of time. DTC Parameters DTC P1133 will set if the O2S-1 signal has not switched greater than 10 times within a 100 second test when: The engine speed is between 1,500-3,000 RPM.=20 The Loop status is closed.=20 The calculated air flow is greater than 7 gm/s.=20 No camshaft (CAM), crankshaft position (CKP), engine coolant temperature (ECT), exhaust gas recirculation (EGR), evaporative emission (EVAP) purge solenoid, fuel trim, intake air temperature (IAT), manifold absolute pressure (MAP), misfire, O2S-1, system voltage or throttle position (TP) sensor DTCs have been set.=20 DTC P1133 diagnostic runs once per ignition cycle once the above conditions have been met. DTC P1133 is a type B DTC. Diagnostic Aids Possible causes of DTC P1133: An intermittent connection or corrosion in the O2S-1 harness connector can set this DTC. Use a scan tool to monitor O2S-1 voltage with engine running at normal operating temperature while wiggling the signal and ground (circuit 413) wire. Make sure the sensor is tight.=20 The most probable cause for DTC P1133 is contamination. Check for obvious contamination, oil, fuel or engine coolant, by removing the sensor. Identify and correct the cause of the contamination if contaminated. Replace the O2S-1.=20 |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Code P1133 on 2000 Saturn SL | Edward Crismond | Saturn | 1 | February 3rd 05 01:25 AM |
2000 Saturn Vibration | Ron Bruno | Saturn | 2 | October 12th 04 01:32 AM |
No reverse gear on 2000 Saturn SL2 A/T | 2000SaturnSL2 | Saturn | 6 | October 6th 04 06:18 PM |
How to remove 2000 Saturn LS1 passenger side mirror | K | Saturn | 3 | October 3rd 04 04:00 PM |
Saturn Lemons- epidemic flaws, engine cracks, ball joints | misterfact | Antique cars | 0 | January 6th 04 06:04 PM |