A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » Dodge
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

turn signal stops blinking and stays solid



 
 
Thread Tools Display Modes
  #1  
Old March 5th 09, 02:40 AM posted to alt.autos.dodge
chrisc
external usenet poster
 
Posts: 5
Default turn signal stops blinking and stays solid

On my driver side of a 2000 grand caravan I have a turn signal
problem. When I pull down to turn the left signal on about half the
time it starts working correctly, then stops blinking (outside and on
dash). It will stay solid green on the dash where the left arrow is
and solid red on the outside rear lens. All the bulbs seem to be good.
Is this an electrical issue? I got lucky on inspection and they didnt
notice. Thanks
Ads
  #2  
Old March 5th 09, 03:33 AM posted to alt.autos.dodge
Dan C
external usenet poster
 
Posts: 134
Default turn signal stops blinking and stays solid

On Wed, 04 Mar 2009 18:40:00 -0800, chrisc wrote:

> On my driver side of a 2000 grand caravan I have a turn signal problem.
> When I pull down to turn the left signal on about half the time it
> starts working correctly, then stops blinking (outside and on dash). It
> will stay solid green on the dash where the left arrow is and solid red
> on the outside rear lens. All the bulbs seem to be good. Is this an
> electrical issue? I got lucky on inspection and they didnt notice.
> Thanks


Bad relay, most likely.


--
"Ubuntu" -- an African word, meaning "Slackware is too hard for me".
The Usenet Improvement Project: http://improve-usenet.org
Ahhhhhhh!: http://brandybuck.site40.net/pics/relieve.jpg
  #3  
Old March 5th 09, 04:21 PM posted to alt.autos.dodge
[email protected]
external usenet poster
 
Posts: 931
Default turn signal stops blinking and stays solid

On 05 Mar 2009 03:33:26 GMT, Dan C >
wrote:

>On Wed, 04 Mar 2009 18:40:00 -0800, chrisc wrote:
>
>> On my driver side of a 2000 grand caravan I have a turn signal problem.
>> When I pull down to turn the left signal on about half the time it
>> starts working correctly, then stops blinking (outside and on dash). It
>> will stay solid green on the dash where the left arrow is and solid red
>> on the outside rear lens. All the bulbs seem to be good. Is this an
>> electrical issue? I got lucky on inspection and they didnt notice.
>> Thanks

>
>Bad relay, most likely.

Double check bulbs. Bad bulb can cause the problem. Not likely the
"relay' If the other side works as it uses the same "relay"
  #4  
Old March 5th 09, 07:35 PM posted to alt.autos.dodge
Dan C
external usenet poster
 
Posts: 134
Default turn signal stops blinking and stays solid

On Thu, 05 Mar 2009 11:21:24 -0500, clare wrote:

> On 05 Mar 2009 03:33:26 GMT, Dan C > wrote:
>
>>On Wed, 04 Mar 2009 18:40:00 -0800, chrisc wrote:
>>
>>> On my driver side of a 2000 grand caravan I have a turn signal
>>> problem. When I pull down to turn the left signal on about half the
>>> time it starts working correctly, then stops blinking (outside and on
>>> dash). It will stay solid green on the dash where the left arrow is
>>> and solid red on the outside rear lens. All the bulbs seem to be good.
>>> Is this an electrical issue? I got lucky on inspection and they didnt
>>> notice. Thanks

>>
>>Bad relay, most likely.

> Double check bulbs. Bad bulb can cause the problem. Not likely the
> "relay' If the other side works as it uses the same "relay"


I think there's a seperate relay for each blinker... Also, in my
experience, a bad bulb will cause a *rapid* blinking, not a steady-on
condition.


--
"Ubuntu" -- an African word, meaning "Slackware is too hard for me".
The Usenet Improvement Project: http://improve-usenet.org
Ahhhhhhh!: http://brandybuck.site40.net/pics/relieve.jpg
  #5  
Old March 5th 09, 09:15 PM posted to alt.autos.dodge
WW[_2_]
external usenet poster
 
Posts: 51
Default turn signal stops blinking and stays solid


> wrote in message
...
> On 05 Mar 2009 03:33:26 GMT, Dan C >
> wrote:
>
>>On Wed, 04 Mar 2009 18:40:00 -0800, chrisc wrote:
>>
>>> On my driver side of a 2000 grand caravan I have a turn signal problem.
>>> When I pull down to turn the left signal on about half the time it
>>> starts working correctly, then stops blinking (outside and on dash). It
>>> will stay solid green on the dash where the left arrow is and solid red
>>> on the outside rear lens. All the bulbs seem to be good. Is this an
>>> electrical issue? I got lucky on inspection and they didnt notice.
>>> Thanks

>>
>>Bad relay, most likely.

> Double check bulbs. Bad bulb can cause the problem. Not likely the
> "relay' If the other side works as it uses the same "relay"


I had this problem and it WAS a bad relay. WW


  #6  
Old March 5th 09, 09:56 PM posted to alt.autos.dodge
chrisc
external usenet poster
 
Posts: 5
Default turn signal stops blinking and stays solid

On Mar 5, 4:15*pm, "WW" > wrote:
> > wrote in message
>
> ...
>
>
>
>
>
> > On 05 Mar 2009 03:33:26 GMT, Dan C >
> > wrote:

>
> >>On Wed, 04 Mar 2009 18:40:00 -0800, chrisc wrote:

>
> >>> On my driver side of a 2000 grand caravan I have a turn signal problem.
> >>> When I pull down to turn the left signal on about half the time it
> >>> starts working correctly, then stops blinking (outside and on dash). It
> >>> will stay solid green on the dash where the left arrow is and solid red
> >>> on the outside rear lens. All the bulbs seem to be good. Is this an
> >>> electrical issue? I got lucky on inspection and they didnt notice.
> >>> Thanks

>
> >>Bad relay, most likely.

> > Double check bulbs. Bad bulb can cause the problem. Not likely the
> > "relay' If the other side works as it uses the same "relay"

>
> I had this problem and it WAS a bad relay. WW- Hide quoted text -
>
> - Show quoted text -


Thanks. I went to the parts store today. I tried a new bulb and that
didn't do it. I forgot to mention that when it happens, the rear light
turns solid and stays solid(even with the ignition off) and the front
light just turns off. By saying light, i mean turn signal not
headlight or brake light. Thanks again for all the replies.
  #7  
Old March 6th 09, 03:29 AM posted to alt.autos.dodge
[email protected]
external usenet poster
 
Posts: 931
Default turn signal stops blinking and stays solid

On 05 Mar 2009 19:35:39 GMT, Dan C >
wrote:

>On Thu, 05 Mar 2009 11:21:24 -0500, clare wrote:
>
>> On 05 Mar 2009 03:33:26 GMT, Dan C > wrote:
>>
>>>On Wed, 04 Mar 2009 18:40:00 -0800, chrisc wrote:
>>>
>>>> On my driver side of a 2000 grand caravan I have a turn signal
>>>> problem. When I pull down to turn the left signal on about half the
>>>> time it starts working correctly, then stops blinking (outside and on
>>>> dash). It will stay solid green on the dash where the left arrow is
>>>> and solid red on the outside rear lens. All the bulbs seem to be good.
>>>> Is this an electrical issue? I got lucky on inspection and they didnt
>>>> notice. Thanks
>>>
>>>Bad relay, most likely.

>> Double check bulbs. Bad bulb can cause the problem. Not likely the
>> "relay' If the other side works as it uses the same "relay"

>
>I think there's a seperate relay for each blinker... Also, in my
>experience, a bad bulb will cause a *rapid* blinking, not a steady-on
>condition.

I have never seen a vehicle with a flasher for each side and I've
been a mechanic for over 40 years.
As for the "failure mode" it depends on the flasher. A thermal type
flasher will not flash with reduced load. Some electronic flashers
flash fast with reduced load. I don't know which type is used on a
2000 GC, and we don't even know if it is still the original flasher -
or if not which type was installed as a replacement.
  #8  
Old March 6th 09, 05:45 PM posted to alt.autos.dodge
jed
external usenet poster
 
Posts: 2
Default turn signal stops blinking and stays solid

the turn signals at the front on the 2000 caravan are also the daytime
running lites.the turn signals and daytime running lites are controlled by a
DRL module which is above your left foot on the firewall on the inside of
the van.I find that when this happens I just cancel the turn signal
operation with the turn signal lever by turning it to the right signal and
then back to neutral position.Replacing the DRL( daytime running lite)
module will correct this problem..
..







"chrisc" > wrote in message
...
On Mar 5, 4:15 pm, "WW" > wrote:
> > wrote in message
>
> ...
>
>
>
>
>
> > On 05 Mar 2009 03:33:26 GMT, Dan C >
> > wrote:

>
> >>On Wed, 04 Mar 2009 18:40:00 -0800, chrisc wrote:

>
> >>> On my driver side of a 2000 grand caravan I have a turn signal
> >>> problem.
> >>> When I pull down to turn the left signal on about half the time it
> >>> starts working correctly, then stops blinking (outside and on dash).
> >>> It
> >>> will stay solid green on the dash where the left arrow is and solid
> >>> red
> >>> on the outside rear lens. All the bulbs seem to be good. Is this an
> >>> electrical issue? I got lucky on inspection and they didnt notice.
> >>> Thanks

>
> >>Bad relay, most likely.

> > Double check bulbs. Bad bulb can cause the problem. Not likely the
> > "relay' If the other side works as it uses the same "relay"

>
> I had this problem and it WAS a bad relay. WW- Hide quoted text -
>
> - Show quoted text -


Thanks. I went to the parts store today. I tried a new bulb and that
didn't do it. I forgot to mention that when it happens, the rear light
turns solid and stays solid(even with the ignition off) and the front
light just turns off. By saying light, i mean turn signal not
headlight or brake light. Thanks again for all the replies.


  #9  
Old March 6th 09, 05:45 PM posted to alt.autos.dodge
jed
external usenet poster
 
Posts: 2
Default turn signal stops blinking and stays solid

the turn signals at the front on the 2000 caravan are also the daytime
running lites.the turn signals and daytime running lites are controlled by a
DRL module which is above your left foot on the firewall on the inside of
the van.I find that when this happens I just cancel the turn signal
operation with the turn signal lever by turning it to the right signal and
then back to neutral position.Replacing the DRL( daytime running lite)
module will correct this problem..
..







"chrisc" > wrote in message
...
On Mar 5, 4:15 pm, "WW" > wrote:
> > wrote in message
>
> ...
>
>
>
>
>
> > On 05 Mar 2009 03:33:26 GMT, Dan C >
> > wrote:

>
> >>On Wed, 04 Mar 2009 18:40:00 -0800, chrisc wrote:

>
> >>> On my driver side of a 2000 grand caravan I have a turn signal
> >>> problem.
> >>> When I pull down to turn the left signal on about half the time it
> >>> starts working correctly, then stops blinking (outside and on dash).
> >>> It
> >>> will stay solid green on the dash where the left arrow is and solid
> >>> red
> >>> on the outside rear lens. All the bulbs seem to be good. Is this an
> >>> electrical issue? I got lucky on inspection and they didnt notice.
> >>> Thanks

>
> >>Bad relay, most likely.

> > Double check bulbs. Bad bulb can cause the problem. Not likely the
> > "relay' If the other side works as it uses the same "relay"

>
> I had this problem and it WAS a bad relay. WW- Hide quoted text -
>
> - Show quoted text -


Thanks. I went to the parts store today. I tried a new bulb and that
didn't do it. I forgot to mention that when it happens, the rear light
turns solid and stays solid(even with the ignition off) and the front
light just turns off. By saying light, i mean turn signal not
headlight or brake light. Thanks again for all the replies.


  #10  
Old March 6th 09, 09:12 PM posted to alt.autos.dodge
JED
external usenet poster
 
Posts: 13
Default turn signal stops blinking and stays solid

the 2000 caravan is equiped with day time running lites which are part of
the front turn signals
The turn signals and day time running lites(DRL) are controlled by the DRL
module which is located on the left side of the interior firewall.when this
happens to me I cancel the left turn signal by applying the turn signal to
the right and then back to neutral.Replacing the DRL module will correct
this problem.




"chrisc" > wrote in message
...
On Mar 5, 4:15 pm, "WW" > wrote:
> > wrote in message
>
> ...
>
>
>
>
>
> > On 05 Mar 2009 03:33:26 GMT, Dan C >
> > wrote:

>
> >>On Wed, 04 Mar 2009 18:40:00 -0800, chrisc wrote:

>
> >>> On my driver side of a 2000 grand caravan I have a turn signal
> >>> problem.
> >>> When I pull down to turn the left signal on about half the time it
> >>> starts working correctly, then stops blinking (outside and on dash).
> >>> It
> >>> will stay solid green on the dash where the left arrow is and solid
> >>> red
> >>> on the outside rear lens. All the bulbs seem to be good. Is this an
> >>> electrical issue? I got lucky on inspection and they didnt notice.
> >>> Thanks

>
> >>Bad relay, most likely.

> > Double check bulbs. Bad bulb can cause the problem. Not likely the
> > "relay' If the other side works as it uses the same "relay"

>
> I had this problem and it WAS a bad relay. WW- Hide quoted text -
>
> - Show quoted text -


Thanks. I went to the parts store today. I tried a new bulb and that
didn't do it. I forgot to mention that when it happens, the rear light
turns solid and stays solid(even with the ignition off) and the front
light just turns off. By saying light, i mean turn signal not
headlight or brake light. Thanks again for all the replies.


 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
turn signal stops flashing KLS Audi 12 February 13th 08 02:51 AM
blinking left-turn red arrow is the safest signal known to man! [email protected] Driving 19 August 3rd 07 05:14 PM
blinking left-turn red arrow is the safest signal known to man! [email protected] Driving 0 August 2nd 07 12:18 AM
Explorer turn signal blinking fast, but bulb has been replaced [email protected] Ford Explorer 6 June 22nd 06 04:33 PM
Neon - rapidly blinking turn signal - diagnosis? Neon96 Dodge 2 August 21st 05 02:10 AM


All times are GMT +1. The time now is 08:26 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.