A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » Jeep
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

2000 TJ 4.0L fuel injectors



 
 
Thread Tools Display Modes
  #1  
Old December 2nd 05, 12:14 AM posted to rec.autos.makers.jeep+willys
external usenet poster
 
Posts: n/a
Default 2000 TJ 4.0L fuel injectors

Matt Osborn did pass the time by typing:
> I have 110,000 miles on my TJ and am losing what I assume to be fuel
> rail pressure when parked for a few hours. Before starting the
> engine, I leave the ignition in the on position for a few seconds
> before cranking the starter. The engine always starts promptly when I
> do this.
>
> Before running up the maintenance bills, cleaning the injectors,
> replacing o-rings, etc., I thought it might be better to simply
> replace the injectors.
>
> I guess what I'm asking is if fuel injectors 'wear out'. That is, how
> long will a set of injectors last?


A set of injectors will last as long as the engine if you maintain the
filter and use good fuel.

Pressure drop in the fuel rail is one of three things.
- fuel pressure regulator
- fuel pump backflow valve
- fuel injectors

And injectors are bloody expensive.
A system called MotorVac can be used to clean the whole thing
from intake to cat. about $100.

First thing to get is a fuel rail pressure gauge. The good ones
have a little hose for dumping fuel. Measure the rail then measure
how fast it drains. Failed check valve in the pump will drop pressure
very quick, failed regulator will give you a low 20-30psi reading rather
than the stock 32 (double check with the dealer to make sure 32 is standard
it was in 93) and your pressure gauge will also drop quickly.

A leaky injector will drop pressure very slowly.

If you want to, you can remove the rail, leave the injectors attached.
Let the pump run and the rail pressurise, then look for drips.

If you do remove/clean/replace the injectors, use new O rings and lube
them with a bit of motor oil so they slide in easily and don't tear.
(and don't loose the clips)

--
-- DougW -- 93 ZJ 4.0 http://revbeergoggles.com
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!


Ads
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
4200 miles in six days in a C6 - fuel use notes for Dad Vandervecken Corvette 9 December 7th 05 10:43 PM
2000 TJ 4.0L fuel injectors Billy Ray Jeep 1 December 2nd 05 12:18 AM
735i - Getting the fuel injectors out BMW 1991 735i BMW 4 November 4th 05 01:58 PM
98 concorde starting problems xmirage2kx Chrysler 90 August 21st 05 04:32 AM
warman i am surprised you mix oil [email protected] Ford Mustang 5 May 8th 05 04:04 AM


All times are GMT +1. The time now is 11:45 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.