A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto newsgroups » Technology
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Brake Splash Guards



 
 
Thread Tools Display Modes
  #1  
Old March 8th 09, 05:53 PM posted to rec.autos.tech
Chris F.
external usenet poster
 
Posts: 101
Default Brake Splash Guards

One more question about the '88 Civic. I've now got the front end taken
apart, and I notice that the brake splash guards are totally rusted away -
only the mounting screws remain, and they appear to be rusted in place.
Should I be worried about replacing these (which involves removing the
press-fitted wheel bearing), or could I just grind off the rusty screw heads
and forget about it? I could also make and weld on some homemade splash
guards from sheet metal.......


Ads
  #2  
Old March 9th 09, 03:46 AM posted to rec.autos.tech
Brent[_4_]
external usenet poster
 
Posts: 4,430
Default Brake Splash Guards

On 2009-03-08, Chris F. > wrote:
> One more question about the '88 Civic. I've now got the front end taken
> apart, and I notice that the brake splash guards are totally rusted away -
> only the mounting screws remain, and they appear to be rusted in place.
> Should I be worried about replacing these (which involves removing the
> press-fitted wheel bearing), or could I just grind off the rusty screw heads
> and forget about it? I could also make and weld on some homemade splash
> guards from sheet metal.......


Sometimes they only serve as dust shields, sometimes they are also used
to channel air to cool the brakes. Also in some cases they might protect
a component like an ABS sensor but that's not going to be an issue on an
'88.

If you can get the mounting bolts free that would be best. Your best
bet at fabing replacements would be to find something close on a car in a
junk yard and modify them to fit.



  #3  
Old March 9th 09, 09:54 PM posted to rec.autos.tech
Tegger[_2_]
external usenet poster
 
Posts: 1,383
Default Brake Splash Guards

"Chris F." > wrote in
:

> One more question about the '88 Civic. I've now got the front end
> taken
> apart, and I notice that the brake splash guards are totally rusted
> away - only the mounting screws remain, and they appear to be rusted
> in place. Should I be worried about replacing these (which involves
> removing the press-fitted wheel bearing), or could I just grind off
> the rusty screw heads and forget about it? I could also make and weld
> on some homemade splash guards from sheet metal.......
>
>
>




I'd replace them with new ones if I were you. Without splash shields, you
may encounter the odd hairy moment where your brakes partially disappear
when passing through deep puddles. New shields are not that expensive ($30-
$40?).

Grind off the heads of the old screws, but leave the stubs slightly proud
of the surface. You'll use those to locate the new shields. Scrape/chisel
off the remains of the old shields, so the steering knuckle mating surface
is clean and smooth.

You'll notice the new shields have a sort of "strap" that's left behind
where the brake caliper aperture is cut out of it. Grind that strap off,
but only cut off enough of it to allow the new shield to be worked over the
hub. The shield can flex quite a bit and still snap back to its original
shape again.

Notice how the hub has a couple of large holes in it? Use those to stick
your drill bit through, so as to make new holes for the new screws in the
steering knuckle. The new screws don't have to be very long; 3/8" is fine.
Locate the new screws near the old ones.

Install new screws. Done.

--
Tegger

 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Car wash won't pay for damaged Beetle engine splash guards! [email protected] VW water cooled 12 April 28th 06 08:52 AM
mud guards 2005 MazdaSpeed? laocmo Mazda 5 March 28th 06 07:14 PM
'03 Rubicon OEM Rocker Guards [email protected] Jeep 1 March 26th 06 03:10 PM
Looking for window guards Sean White Ford Mustang 1 August 17th 05 02:09 AM
Splash guards Ct Midnite BMW 3 May 11th 05 02:59 AM


All times are GMT +1. The time now is 10:29 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.