If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
NEED rubber seal for Girling Clutch Slave Cylinder CJ with AMC 150
The Girling clutch slave cylinder on my CJ5, 1981 with the AMC 150
four-banger engine is Jeep Part #52000070. Inside the cylinder ther are only two parts, a metal pison and a rubber seal that follows the piston in and out. I want just the rubber seal that goes on the piston but can not find one anywhere. I dont want to pay $70 for a new unit as the bore and piston is in fine shape. Only the rubber seal is worn. Can anyone direct me to a source for this seal OR if its not available is there any treatment I can give the rubber to swell it or such? I have tried silicone paste but that had no effect. The leak is sligh. Needs bleeding every week or two. Michael |
Ads |
#2
|
|||
|
|||
NEED rubber seal for Girling Clutch Slave Cylinder CJ with AMC 150
Just go to your mom and pop brake shop/jobber in your town, they have
bins full of cups by size like yours marked maybe 5/8", for about ten cents. God Bless America, Bill 0|||||||0 http://www.billhughes.com/ "MStevens003" > wrote in message ... > The Girling clutch slave cylinder on my CJ5, 1981 with the AMC 150 > four-banger engine is Jeep Part #52000070. Inside the cylinder ther are only > two parts, a metal pison and a rubber seal that follows the piston in and > out. I want just the rubber seal that goes on the piston but can not find > one anywhere. I dont want to pay $70 for a new unit as the bore and piston > is in fine shape. Only the rubber seal is worn. > Can anyone direct me to a source for this seal OR > if its not available is there any treatment I can give the rubber to swell > it or such? I have tried silicone paste but that had no effect. The leak is > sligh. Needs bleeding every week or two. > > Michael > > -- Posted via a free Usenet account from http://www.teranews.com |
#3
|
|||
|
|||
NEED rubber seal for Girling Clutch Slave Cylinder CJ with AMC 150
And God Bless You too Bill. Thanks.
"L.W. (Bill) Hughes III" > wrote in message .. . > Just go to your mom and pop brake shop/jobber in your town, they have > bins full of cups by size like yours marked maybe 5/8", for about ten > cents. > God Bless America, Bill 0|||||||0 > http://www.billhughes.com/ > > "MStevens003" > wrote in message > ... >> The Girling clutch slave cylinder on my CJ5, 1981 with the AMC 150 >> four-banger engine is Jeep Part #52000070. Inside the cylinder ther are > only >> two parts, a metal pison and a rubber seal that follows the piston in and >> out. I want just the rubber seal that goes on the piston but can not find >> one anywhere. I dont want to pay $70 for a new unit as the bore and >> piston >> is in fine shape. Only the rubber seal is worn. >> Can anyone direct me to a source for this seal OR >> if its not available is there any treatment I can give the rubber to >> swell >> it or such? I have tried silicone paste but that had no effect. The leak > is >> sligh. Needs bleeding every week or two. >> >> Michael >> >> > > > > -- > Posted via a free Usenet account from http://www.teranews.com > |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Audi100, '89: Clutch slave cylinder replace or new seals? | Christoph Bollig | Audi | 2 | October 4th 06 09:07 AM |
Ford F-150 clutch slave cylinder replacement | George Brims | Technology | 4 | September 13th 06 01:53 AM |
Clutch Slave Cylinder - New or Rebuilt? | mjb920 | Mazda | 2 | March 1st 05 06:35 PM |
Bleeding clutch master cylinder/slave | [email protected] | Mazda | 3 | January 23rd 05 12:55 AM |
94 Civic: boot the clutch slave cylinder goes into?? | Abeness | Honda | 2 | November 16th 04 05:26 AM |