If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
RBR : Big problem, can't create driver profile
Just imported Richard Burns Rally from the UK. The host system is a Athlon
2400 / XP SP2 / Radeon 9600 with latest drivers / 1GB memory. This system has run everything I've thrown at it - development tools, VMware, GPL, F1C, etc. RBR starts up fine, then gets to the "create driver profile" screen, and that is as far as it goes - both the mouse and the keyboard are dead, I can't select or enter anything. I have patched RBR up to 1.02. Has anyone seen this? Any suggestions? Help! |
Ads |
#2
|
|||
|
|||
Tom Leathley wrote:
> Just imported Richard Burns Rally from the UK. The host system is a Athlon > 2400 / XP SP2 / Radeon 9600 with latest drivers / 1GB memory. This system > has run everything I've thrown at it - development tools, VMware, GPL, F1C, > etc. > > RBR starts up fine, then gets to the "create driver profile" screen, and > that is as far as it goes - both the mouse and the keyboard are dead, I > can't select or enter anything. I have patched RBR up to 1.02. > > Has anyone seen this? Any suggestions? > > Help! > > I have a very similar system (3200+ with a 9600XT card and 1.5GB mem) and that you have to disable AGP write in ATI's catalyst control center. You'll have to switch to advanced view in the control center and then under SMARTGART there is a checkbox for AGP Write. Failing that, you might want to check out the forums at www.racesimcentral.com since there seems to be a wealth of knowledge there too Hope that helps, DanK |
#3
|
|||
|
|||
"Tom Leathley" > wrote in message ... > Just imported Richard Burns Rally from the UK. The host system is a Athlon > 2400 / XP SP2 / Radeon 9600 with latest drivers / 1GB memory. This system > has run everything I've thrown at it - development tools, VMware, GPL, F1C, > etc. > > RBR starts up fine, then gets to the "create driver profile" screen, and > that is as far as it goes - both the mouse and the keyboard are dead, I > can't select or enter anything. I have patched RBR up to 1.02. > > Has anyone seen this? Any suggestions? Similar system, SP1, 9700Pro latest drivers, no problems - do remember that there is no mouse control, tho. Arrows only for navigation. Regards, Mark at v8thunder dot com |
#4
|
|||
|
|||
set the game to low detail level.
Charlie |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 7 | February 1st 05 01:43 PM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 10 | January 2nd 05 05:15 AM |
New *FREE* Corvette Discussion Forum | JLA ENTERPRISES TECHNOLOGIES INTEGRATION | Corvette | 12 | November 30th 04 06:36 PM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 10 | November 1st 04 05:24 AM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 10 | October 16th 04 05:28 AM |