A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » Audi
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Audi 4000s fuel problem - wont start



 
 
Thread Tools Display Modes
  #1  
Old January 2nd 07, 04:47 AM posted to alt.autos.audi
[email protected]
external usenet poster
 
Posts: 4
Default Audi 4000s fuel problem - wont start

I was wondering of anyone could help me with a problem that suddenly
developed with my AUDI,

The car is a 1987 Audi 4000s 1.8L
Here is the deal, the car will start for second or two, but will not
rev up, then it dies.

Fuel pump and filters are new.

Strong fuel pressure to the Fuel injector unit.

The injector unit is sending fuel to the cold start valve, but not to
the cylinders, thus the car will start but will not continue to run.
The pressure to the cold start valve is strong, but not a drop to the
fuel injectors.

I replaced the external fuel regulator with a spare one and checked for
vacuum leaks etc.

I am not sure where to look from here, internally on the Fuel Injection
Unit, or to a relay or other control.

As I stated the problem happened overnight.

Any help would be appreciated.
I have not used a internet group before, do I hope I am doing this
right...........





Thanks,



Richy Jackson

  #2  
Old January 2nd 07, 09:55 AM posted to alt.autos.audi
TonyJ
external usenet poster
 
Posts: 80
Default Audi 4000s fuel problem - wont start



wrote:
> I was wondering of anyone could help me with a problem that suddenly
> developed with my AUDI,
>
> The car is a 1987 Audi 4000s 1.8L
> Here is the deal, the car will start for second or two, but will not
> rev up, then it dies.
>
> Fuel pump and filters are new.
>
> Strong fuel pressure to the Fuel injector unit.
>
> The injector unit is sending fuel to the cold start valve, but not to
> the cylinders, thus the car will start but will not continue to run.
> The pressure to the cold start valve is strong, but not a drop to the
> fuel injectors.
>
> I replaced the external fuel regulator with a spare one and checked for
> vacuum leaks etc.
>
> I am not sure where to look from here, internally on the Fuel Injection
> Unit, or to a relay or other control.
>
> As I stated the problem happened overnight.
>
> Any help would be appreciated.
> I have not used a internet group before, do I hope I am doing this
> right...........
>
>
>
>
>
> Thanks,
>
>
>
> Richy Jackson
>

If the air plate just above the air filter is stuck the injectors will not fire.
This can be due to vacuum leaks (you checked but check again) or deposits on
the rod above the plate.

Open air cleaner and reach up into the intake just above. The plate should move
but with a little pressure. Don't force it.

Other ideas:
Differential fuel pressure sensor (just in front of fuel distributor.

Blown engine management fuse (in the side of the relay box.

Failing engine temp sensor. In the T44s it is called the MFTS and it is located
by the upper radiator hose inlet to the engine.
  #3  
Old January 3rd 07, 05:07 AM posted to alt.autos.audi
dave AKA vwdoc1
external usenet poster
 
Posts: 951
Default Audi 4000s fuel problem - wont start

Like TonyJ said..............it might be a Failing engine coolant temp
sensor (CTS)

Or a fuse in the fuse box. It is positioned to look like a spare fuse and
many times I will find it missing on a vehicle that is not running right if
running at all. 8^o
Examine all of the fuses for any broken ones and stick a fuse in all sockets
with terminals.

Or it could be the ground wire for the fuel pressure regulator is broken and
it should be located at the cold start valve.

Or it could be a defective fuel distributor.

Or it could be a massive air leak at the large intake manifold boots. Maybe
a light engine backfire into the intake system along with the gas pedal
being depressed might have caused a hose/pipe to pop off creating a large
vacuum leak.

Or it could be the ign switch not allowing power to the systems when it is
in the ON position. Telltale signs would be those red idiot lights not
being ON with the ign ON or while cranking over the engine.

good luck and let us know what happens!
later,
dave
AKA vwdoc1

"TonyJ" > wrote in message
...
>
>
> wrote:
>> I was wondering of anyone could help me with a problem that suddenly
>> developed with my AUDI,
>>
>> The car is a 1987 Audi 4000s 1.8L
>> Here is the deal, the car will start for second or two, but will not
>> rev up, then it dies.
>>
>> Fuel pump and filters are new.
>>
>> Strong fuel pressure to the Fuel injector unit.
>>
>> The injector unit is sending fuel to the cold start valve, but not to
>> the cylinders, thus the car will start but will not continue to run.
>> The pressure to the cold start valve is strong, but not a drop to the
>> fuel injectors.
>>
>> I replaced the external fuel regulator with a spare one and checked for
>> vacuum leaks etc.
>>
>> I am not sure where to look from here, internally on the Fuel Injection
>> Unit, or to a relay or other control.
>>
>> As I stated the problem happened overnight.
>>
>> Any help would be appreciated.
>> I have not used a internet group before, do I hope I am doing this
>> right...........
>>
>>
>>
>>
>>
>> Thanks,
>>
>>
>>
>> Richy Jackson
>>

> If the air plate just above the air filter is stuck the injectors will not
> fire. This can be due to vacuum leaks (you checked but check again) or
> deposits on the rod above the plate.
>
> Open air cleaner and reach up into the intake just above. The plate should
> move but with a little pressure. Don't force it.
>
> Other ideas:
> Differential fuel pressure sensor (just in front of fuel distributor.
>
> Blown engine management fuse (in the side of the relay box.
>
> Failing engine temp sensor. In the T44s it is called the MFTS and it is
> located by the upper radiator hose inlet to the engine.



  #4  
Old February 4th 07, 09:00 PM posted to alt.autos.audi
[email protected]
external usenet poster
 
Posts: 4
Default Audi 4000s fuel problem - wont start

Hello Audi 4000 fuel help still needed

Been busy at work, not much time to work on the Audi until last week.

Still having problems getting this car to run, was wondering if there
are any other ideas out there?

I still can not get the fuel injector unit to shoot fuel into the
injectors. It still fires fuel to the cold start valve, enough juice
to run 3-5 seconds.

I checked all fuses, put new ones in the blank spaces.

I checked the fuel injector air-door, it opened fine.

I replaced the entire fuel injector unit with a used one I had from a
parts lot I bought.

I changed the fuel regulator as well, the one on the injector unit, I
believe this is the "Differential fuel pressure sensor (just in
front of fuel distributor." ,that you mentioned
As far as the "Failing engine temp senso" " the MFTS ", is this the
same as the temperature sending switch? . Could this really keep the
fuel injector unit from firing? Can I bypass this to test it?
There is no massive air leak at the large intake manifold
The ignition switch is fine, it is new, it is getting power to the
fuel pump and other systems

Any help would be appreciated!!

Richy Jackson
On Jan 2, 11:07 pm, "dave AKA vwdoc1" > wrote:
> Like TonyJ said..............it might be a Failing engine coolant temp
> sensor (CTS)
>
> Or a fuse in the fuse box. It is positioned to look like a spare fuse and
> many times I will find it missing on a vehicle that is not running right if
> running at all. 8^o
> Examine all of the fuses for any broken ones and stick a fuse in all sockets
> with terminals.
>
> Or it could be the ground wire for the fuel pressure regulator is broken and
> it should be located at the cold start valve.
>
> Or it could be a defective fuel distributor.
>
> Or it could be a massive air leak at the large intake manifold boots. Maybe
> a light engine backfire into the intake system along with the gas pedal
> being depressed might have caused a hose/pipe to pop off creating a large
> vacuum leak.
>
> Or it could be the ign switch not allowing power to the systems when it is
> in the ON position. Telltale signs would be those red idiot lights not
> being ON with the ign ON or while cranking over the engine.
>
> good luck and let us know what happens!
> later,
> dave
> AKA vwdoc1
>
> "TonyJ" > wrote in message
>
> ...
>
>
>
>
>
> > wrote:
> >> I was wondering of anyone could help me with a problem that suddenly
> >> developed with my AUDI,

>
> >> The car is a 1987 Audi 4000s 1.8L
> >> Here is the deal, the car will start for second or two, but will not
> >> rev up, then it dies.

>
> >> Fuel pump and filters are new.

>
> >> Strong fuel pressure to the Fuel injector unit.

>
> >> The injector unit is sending fuel to the cold start valve, but not to
> >> the cylinders, thus the car will start but will not continue to run.
> >> The pressure to the cold start valve is strong, but not a drop to the
> >> fuel injectors.

>
> >> I replaced the external fuel regulator with a spare one and checked for
> >> vacuum leaks etc.

>
> >> I am not sure where to look from here, internally on the Fuel Injection
> >> Unit, or to a relay or other control.

>
> >> As I stated the problem happened overnight.

>
> >> Any help would be appreciated.
> >> I have not used a internet group before, do I hope I am doing this
> >> right...........

>
> >> Thanks,

>
> >> Richy Jackson

>
> > If the air plate just above the air filter is stuck the injectors will not
> > fire. This can be due to vacuum leaks (you checked but check again) or
> > deposits on the rod above the plate.

>
> > Open air cleaner and reach up into the intake just above. The plate should
> > move but with a little pressure. Don't force it.

>
> > Other ideas:
> > Differential fuel pressure sensor (just in front of fuel distributor.

>
> > Blown engine management fuse (in the side of the relay box.

>
> > Failing engine temp sensor. In the T44s it is called the MFTS and it is
> > located by the upper radiator hose inlet to the engine.- Hide quoted text -

>
> - Show quoted text -



  #5  
Old February 5th 07, 12:13 AM posted to alt.autos.audi
dave AKA vwdoc1
external usenet poster
 
Posts: 951
Default '87 Audi 4000s fuel problem - wont start

Do you have a repair manual? Even a Haynes (cough cough) could help some.

Remove intake boot off of fuel distributor so you can manually lift up the
plate.
Remove injector(s) out of the cylinder head and aim into a container so you
can examine spray pattern.
Remove fuel pump and jump correct wires to run fuel pump continually.
Turn ign on but do not start car.

Pull up on fuel distributor plate to check fuel injector spray pattern.
Tell us what happens?
If it sprays out that is good and you might just need to adjust something or
change a sensor.
If nothing sprays out then I suspect either a bad fuel distributor, bad Fuel
Pressure Regulator, bad wiring, missing fuse, clogged injectors, no fuel
pressure or ????

The ground wire for the FPR usually breaks at the cold start valve.

No the temperature sensor for the gauge is different than the one for the
fuel injection. ;-)

later,
dave
(One out of many daves)

> wrote in message
oups.com...
> Hello Audi 4000 fuel help still needed
>
> Been busy at work, not much time to work on the Audi until last week.
>
> Still having problems getting this car to run, was wondering if there
> are any other ideas out there?
>
> I still can not get the fuel injector unit to shoot fuel into the
> injectors. It still fires fuel to the cold start valve, enough juice
> to run 3-5 seconds.
>
> I checked all fuses, put new ones in the blank spaces.
>
> I checked the fuel injector air-door, it opened fine.
>
> I replaced the entire fuel injector unit with a used one I had from a
> parts lot I bought.
>
> I changed the fuel regulator as well, the one on the injector unit, I
> believe this is the "Differential fuel pressure sensor (just in
> front of fuel distributor." ,that you mentioned
> As far as the "Failing engine temp senso" " the MFTS ", is this the
> same as the temperature sending switch? . Could this really keep the
> fuel injector unit from firing? Can I bypass this to test it?
> There is no massive air leak at the large intake manifold
> The ignition switch is fine, it is new, it is getting power to the
> fuel pump and other systems
>
> Any help would be appreciated!!
>
> Richy Jackson
> On Jan 2, 11:07 pm, "dave AKA vwdoc1" > wrote:
>> Like TonyJ said..............it might be a Failing engine coolant temp
>> sensor (CTS)
>>
>> Or a fuse in the fuse box. It is positioned to look like a spare fuse
>> and
>> many times I will find it missing on a vehicle that is not running right
>> if
>> running at all. 8^o
>> Examine all of the fuses for any broken ones and stick a fuse in all
>> sockets
>> with terminals.
>>
>> Or it could be the ground wire for the fuel pressure regulator is broken
>> and
>> it should be located at the cold start valve.
>>
>> Or it could be a defective fuel distributor.
>>
>> Or it could be a massive air leak at the large intake manifold boots.
>> Maybe
>> a light engine backfire into the intake system along with the gas pedal
>> being depressed might have caused a hose/pipe to pop off creating a large
>> vacuum leak.
>>
>> Or it could be the ign switch not allowing power to the systems when it
>> is
>> in the ON position. Telltale signs would be those red idiot lights not
>> being ON with the ign ON or while cranking over the engine.
>>
>> good luck and let us know what happens!
>> later,
>> dave
>> AKA vwdoc1
>>
>> "TonyJ" > wrote in message
>>
>> ...
>>
>>
>>
>>
>>
>> > wrote:
>> >> I was wondering of anyone could help me with a problem that suddenly
>> >> developed with my AUDI,

>>
>> >> The car is a 1987 Audi 4000s 1.8L
>> >> Here is the deal, the car will start for second or two, but will not
>> >> rev up, then it dies.

>>
>> >> Fuel pump and filters are new.

>>
>> >> Strong fuel pressure to the Fuel injector unit.

>>
>> >> The injector unit is sending fuel to the cold start valve, but not to
>> >> the cylinders, thus the car will start but will not continue to run.
>> >> The pressure to the cold start valve is strong, but not a drop to the
>> >> fuel injectors.

>>
>> >> I replaced the external fuel regulator with a spare one and checked
>> >> for
>> >> vacuum leaks etc.

>>
>> >> I am not sure where to look from here, internally on the Fuel
>> >> Injection
>> >> Unit, or to a relay or other control.

>>
>> >> As I stated the problem happened overnight.

>>
>> >> Any help would be appreciated.
>> >> I have not used a internet group before, do I hope I am doing this
>> >> right...........

>>
>> >> Thanks,

>>
>> >> Richy Jackson

>>
>> > If the air plate just above the air filter is stuck the injectors will
>> > not
>> > fire. This can be due to vacuum leaks (you checked but check again)
>> > or
>> > deposits on the rod above the plate.

>>
>> > Open air cleaner and reach up into the intake just above. The plate
>> > should
>> > move but with a little pressure. Don't force it.

>>
>> > Other ideas:
>> > Differential fuel pressure sensor (just in front of fuel distributor.

>>
>> > Blown engine management fuse (in the side of the relay box.

>>
>> > Failing engine temp sensor. In the T44s it is called the MFTS and it is
>> > located by the upper radiator hose inlet to the engine.- Hide quoted
>> > text -

>>
>> - Show quoted text -

>
>



  #6  
Old February 5th 07, 05:47 AM posted to alt.autos.audi
[email protected]
external usenet poster
 
Posts: 4
Default '87 Audi 4000s fuel problem - wont start

On Feb 4, 6:13 pm, "dave AKA vwdoc1" > wrote:
> Do you have a repair manual? Even a Haynes (cough cough) could help some.
>
> Remove intake boot off of fuel distributor so you can manually lift up the
> plate.
> Remove injector(s) out of the cylinder head and aim into a container so you
> can examine spray pattern.
> Remove fuel pump and jump correct wires to run fuel pump continually.
> Turn ign on but do not start car.
>
> Pull up on fuel distributor plate to check fuel injector spray pattern.
> Tell us what happens?
> If it sprays out that is good and you might just need to adjust something or
> change a sensor.
> If nothing sprays out then I suspect either a bad fuel distributor, bad Fuel
> Pressure Regulator, bad wiring, missing fuse, clogged injectors, no fuel
> pressure or ????
>
> The ground wire for the FPR usually breaks at the cold start valve.
>
> No the temperature sensor for the gauge is different than the one for the
> fuel injection. ;-)
>
> later,
> dave
> (One out of many daves)
>
> > wrote in message
>
> oups.com...
>
>
>
> > Hello Audi 4000 fuel help still needed

>
> > Been busy at work, not much time to work on the Audi until last week.

>
> > Still having problems getting this car to run, was wondering if there
> > are any other ideas out there?

>
> > I still can not get the fuel injector unit to shoot fuel into the
> > injectors. It still fires fuel to the cold start valve, enough juice
> > to run 3-5 seconds.

>
> > I checked all fuses, put new ones in the blank spaces.

>
> > I checked the fuel injector air-door, it opened fine.

>
> > I replaced the entire fuel injector unit with a used one I had from a
> > parts lot I bought.

>
> > I changed the fuel regulator as well, the one on the injector unit, I
> > believe this is the "Differential fuel pressure sensor (just in
> > front of fuel distributor." ,that you mentioned
> > As far as the "Failing engine temp senso" " the MFTS ", is this the
> > same as the temperature sending switch? . Could this really keep the
> > fuel injector unit from firing? Can I bypass this to test it?
> > There is no massive air leak at the large intake manifold
> > The ignition switch is fine, it is new, it is getting power to the
> > fuel pump and other systems

>
> > Any help would be appreciated!!

>
> > Richy Jackson
> > On Jan 2, 11:07 pm, "dave AKA vwdoc1" > wrote:
> >> Like TonyJ said..............it might be a Failing engine coolant temp
> >> sensor (CTS)

>
> >> Or a fuse in the fuse box. It is positioned to look like a spare fuse
> >> and
> >> many times I will find it missing on a vehicle that is not running right
> >> if
> >> running at all. 8^o
> >> Examine all of the fuses for any broken ones and stick a fuse in all
> >> sockets
> >> with terminals.

>
> >> Or it could be the ground wire for the fuel pressure regulator is broken
> >> and
> >> it should be located at the cold start valve.

>
> >> Or it could be a defective fuel distributor.

>
> >> Or it could be a massive air leak at the large intake manifold boots.
> >> Maybe
> >> a light engine backfire into the intake system along with the gas pedal
> >> being depressed might have caused a hose/pipe to pop off creating a large
> >> vacuum leak.

>
> >> Or it could be the ign switch not allowing power to the systems when it
> >> is
> >> in the ON position. Telltale signs would be those red idiot lights not
> >> being ON with the ign ON or while cranking over the engine.

>
> >> good luck and let us know what happens!
> >> later,
> >> dave
> >> AKA vwdoc1

>
> >> "TonyJ" > wrote in message

>
> ...

>
> >> > wrote:
> >> >> I was wondering of anyone could help me with a problem that suddenly
> >> >> developed with my AUDI,

>
> >> >> The car is a 1987 Audi 4000s 1.8L
> >> >> Here is the deal, the car will start for second or two, but will not
> >> >> rev up, then it dies.

>
> >> >> Fuel pump and filters are new.

>
> >> >> Strong fuel pressure to the Fuel injector unit.

>
> >> >> The injector unit is sending fuel to the cold start valve, but not to
> >> >> the cylinders, thus the car will start but will not continue to run.
> >> >> The pressure to the cold start valve is strong, but not a drop to the
> >> >> fuel injectors.

>
> >> >> I replaced the external fuel regulator with a spare one and checked
> >> >> for
> >> >> vacuum leaks etc.

>
> >> >> I am not sure where to look from here, internally on the Fuel
> >> >> Injection
> >> >> Unit, or to a relay or other control.

>
> >> >> As I stated the problem happened overnight.

>
> >> >> Any help would be appreciated.
> >> >> I have not used a internet group before, do I hope I am doing this
> >> >> right...........

>
> >> >> Thanks,

>
> >> >> Richy Jackson

>
> >> > If the air plate just above the air filter is stuck the injectors will
> >> > not
> >> > fire. This can be due to vacuum leaks (you checked but check again)
> >> > or
> >> > deposits on the rod above the plate.

>
> >> > Open air cleaner and reach up into the intake just above. The plate
> >> > should
> >> > move but with a little pressure. Don't force it.

>
> >> > Other ideas:
> >> > Differential fuel pressure sensor (just in front of fuel distributor.

>
> >> > Blown engine management fuse (in the side of the relay box.

>
> >> > Failing engine temp sensor. In the T44s it is called the MFTS and it is
> >> > located by the upper radiator hose inlet to the engine.- Hide quoted
> >> > text -

>
> >> - Show quoted text -- Hide quoted text -

>
> - Show quoted text -



Hey Dave,

Thanks for the reply,

Yup, I have a good old Haynes manual; read it a couple times...!! I will
get a shop manual..

I did take off the hoses to the fuel injectors and cranked the engine,
nothing comes out, except for the line to the Cold Star Valve that
gives a nice spray to the intake...

I tested this with both my original, and a replacement fuel injector
unit, in both cases, plenty of fuel to cold start valve, nothing to
fuel injectors. I already pulled the plate up as you suggest. still
nothing from the fuel injector hoses

Replaced both fuel regulators, car has new fuel pump and filters,
plenty of fuel pressure to injector unit...

The ground to the cold start valve is fine

As I have tried a replacement injector unit, it does the same thing, I
am thinking it I electrical, fuses are good.

I read the voltage of the fuel regulator that is on the fuel
distributor unit or, it shows 8 v, there is an electrical connection
on the other side.

Something is keeping the Fuel distributor unit from shooting fuel to
the injectors, any other thoughts?

Tell me again about the temp sensor for the fuel distributor, where is
it located & would it stop the fuel injector unit from firing?

This car ran fine until a couple months ago, I changed brake lines &
complete exhaust & then it stopped running...

Any help would be cool..


Richy Jackson




  #7  
Old February 11th 07, 06:07 PM posted to alt.autos.audi
mark / susan lemon
external usenet poster
 
Posts: 1
Default Audi 4000s fuel problem - wont start

The temp sensor (in a coolant manifold) is an input to a box located behind
the glove compartment. An output of that box provides current to the gray
box on the side of the mixture control unit (differential pressure
regulator). More current = richer mixture. Open circuit = very lean
mixture. The proper / quick check is to measure the current through the
differential pressure regulator but that is difficult to do without the test
jig and a solid electrical theory in mind.. I believe the normal current is
in the 100ma range. It's in the books but they make it harder to find as
time passes.

Doubt that the control box would actually fail unless there has been a major
electrical event. Once I found / replaced an open transistor in the box and
we drove it for years, but I'd purchased that car due to it's having an
electrical fire due to the radiator cooling fan.. Oh those days of $1200
Audi 4000s.

I'd be crawling around under the glove box, looking for where the mice have
been unless you have a Fluke 77 and feel like cutting wires.

mark lemon
Woodward Iowa

> wrote in message
oups.com...
> Hello Audi 4000 fuel help still needed
>
> Been busy at work, not much time to work on the Audi until last week.
>
> Still having problems getting this car to run, was wondering if there
> are any other ideas out there?
>
> I still can not get the fuel injector unit to shoot fuel into the
> injectors. It still fires fuel to the cold start valve, enough juice
> to run 3-5 seconds.
>
> I checked all fuses, put new ones in the blank spaces.
>
> I checked the fuel injector air-door, it opened fine.
>
> I replaced the entire fuel injector unit with a used one I had from a
> parts lot I bought.
>
> I changed the fuel regulator as well, the one on the injector unit, I
> believe this is the "Differential fuel pressure sensor (just in
> front of fuel distributor." ,that you mentioned
> As far as the "Failing engine temp senso" " the MFTS ", is this the
> same as the temperature sending switch? . Could this really keep the
> fuel injector unit from firing? Can I bypass this to test it?
> There is no massive air leak at the large intake manifold
> The ignition switch is fine, it is new, it is getting power to the
> fuel pump and other systems
>
> Any help would be appreciated!!
>
> Richy Jackson
> On Jan 2, 11:07 pm, "dave AKA vwdoc1" > wrote:
>> Like TonyJ said..............it might be a Failing engine coolant temp
>> sensor (CTS)
>>
>> Or a fuse in the fuse box. It is positioned to look like a spare fuse
>> and
>> many times I will find it missing on a vehicle that is not running right
>> if
>> running at all. 8^o
>> Examine all of the fuses for any broken ones and stick a fuse in all
>> sockets
>> with terminals.
>>
>> Or it could be the ground wire for the fuel pressure regulator is broken
>> and
>> it should be located at the cold start valve.
>>
>> Or it could be a defective fuel distributor.
>>
>> Or it could be a massive air leak at the large intake manifold boots.
>> Maybe
>> a light engine backfire into the intake system along with the gas pedal
>> being depressed might have caused a hose/pipe to pop off creating a large
>> vacuum leak.
>>
>> Or it could be the ign switch not allowing power to the systems when it
>> is
>> in the ON position. Telltale signs would be those red idiot lights not
>> being ON with the ign ON or while cranking over the engine.
>>
>> good luck and let us know what happens!
>> later,
>> dave
>> AKA vwdoc1
>>
>> "TonyJ" > wrote in message
>>
>> ...
>>
>>
>>
>>
>>
>> > wrote:
>> >> I was wondering of anyone could help me with a problem that suddenly
>> >> developed with my AUDI,

>>
>> >> The car is a 1987 Audi 4000s 1.8L
>> >> Here is the deal, the car will start for second or two, but will not
>> >> rev up, then it dies.

>>
>> >> Fuel pump and filters are new.

>>
>> >> Strong fuel pressure to the Fuel injector unit.

>>
>> >> The injector unit is sending fuel to the cold start valve, but not to
>> >> the cylinders, thus the car will start but will not continue to run.
>> >> The pressure to the cold start valve is strong, but not a drop to the
>> >> fuel injectors.

>>
>> >> I replaced the external fuel regulator with a spare one and checked
>> >> for
>> >> vacuum leaks etc.

>>
>> >> I am not sure where to look from here, internally on the Fuel
>> >> Injection
>> >> Unit, or to a relay or other control.

>>
>> >> As I stated the problem happened overnight.

>>
>> >> Any help would be appreciated.
>> >> I have not used a internet group before, do I hope I am doing this
>> >> right...........

>>
>> >> Thanks,

>>
>> >> Richy Jackson

>>
>> > If the air plate just above the air filter is stuck the injectors will
>> > not
>> > fire. This can be due to vacuum leaks (you checked but check again)
>> > or
>> > deposits on the rod above the plate.

>>
>> > Open air cleaner and reach up into the intake just above. The plate
>> > should
>> > move but with a little pressure. Don't force it.

>>
>> > Other ideas:
>> > Differential fuel pressure sensor (just in front of fuel distributor.

>>
>> > Blown engine management fuse (in the side of the relay box.

>>
>> > Failing engine temp sensor. In the T44s it is called the MFTS and it is
>> > located by the upper radiator hose inlet to the engine.- Hide quoted
>> > text -

>>
>> - Show quoted text -

>
>



  #8  
Old January 8th 17, 05:18 PM posted to alt.autos.audi
buttholelicker69
external usenet poster
 
Posts: 1
Default Audi 4000s fuel problem - wont start

replying to iamsiam, buttholelicker69 wrote:
two wires coming from ecu. check if they are grounded to intake manifold. they
look like two other wires that go to CIS-E.

--
for full context, visit http://www.motorsforum.com/audi/audi...tart-6905-.htm


  #9  
Old March 5th 07, 08:28 AM posted to alt.autos.audi
Audrey[_2_]
external usenet poster
 
Posts: 2
Default Audi 4000s fuel problem - wont start

Try replacing the temperature control switch which could be sending a
false reading to your ECU hence no fuel in cylinders.

"TonyJ" wrote:
> wrote:
> > I was wondering of anyone could help me with a problem that

> suddenly
> > developed with my AUDI,
> >
> > The car is a 1987 Audi 4000s 1.8L
> > Here is the deal, the car will start for second or two, but

> will not
> > rev up, then it dies.
> >
> > Fuel pump and filters are new.
> >
> > Strong fuel pressure to the Fuel injector unit.
> >
> > The injector unit is sending fuel to the cold start valve,

> but not to
> > the cylinders, thus the car will start but will not continue

> to run.
> > The pressure to the cold start valve is strong, but not a

> drop to the
> > fuel injectors.
> >
> > I replaced the external fuel regulator with a spare one and

> checked for
> > vacuum leaks etc.
> >
> > I am not sure where to look from here, internally on the

> Fuel Injection
> > Unit, or to a relay or other control.
> >
> > As I stated the problem happened overnight.
> >
> > Any help would be appreciated.
> > I have not used a internet group before, do I hope I am

> doing this
> > right...........
> >
> >
> >
> >
> >
> > Thanks,
> >
> >
> >
> > Richy Jackson
> >

> If the air plate just above the air filter is stuck the
> injectors will not fire.
> This can be due to vacuum leaks (you checked but check
> again) or deposits on
> the rod above the plate.
>
> Open air cleaner and reach up into the intake just above. The
> plate should move
> but with a little pressure. Don't force it.
>
> Other ideas:
> Differential fuel pressure sensor (just in front of fuel
> distributor.
>
> Blown engine management fuse (in the side of the relay box.
>
> Failing engine temp sensor. In the T44s it is called the MFTS
> and it is located
> by the upper radiator hose inlet to the engine.


--
Posted at author's request, using
http://www.AutoBoardz.com interface
Articles individually verified to usenet standards. Visit URL to contact author/report abuse
Thread archive: http://www.AutoBoardz.com/4000s-fuel...ict202188.html

 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Audi 100 5cyl cold start problem sealdogfish Audi 25 June 7th 16 08:39 AM
OEM Audi parts catalogs for sale Joe Audi 0 April 2nd 06 08:54 PM
Ping Tigger: case study on rear O2 sensor and fuel trim Stephen H Honda 0 December 24th 05 06:37 AM
Why you should never buy a car without a tachometer Ted B. Driving 112 September 19th 05 04:09 AM
98 concorde starting problems xmirage2kx Chrysler 90 August 21st 05 04:32 AM


All times are GMT +1. The time now is 11:58 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.