![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]()
I replaced my starter with a 'new' rebuilt one...
When I turn the ignition, there's a grinding noise momentarily and then it starts. I removed it to check the flywheel gears and the starter gear look fine, no shavings. Is it possible the starter is bad? What else should I check? tia, -- Mel P. parts for sale http://melsvws.4t.com/vwparts/index.htm 77 Bug - stock FI http://melsvws.4t.com/77bug/index.htm 70 KG Cabrio http://melsvws.4t.com/70ghia/index.htm |
Ads |
#2
|
|||
|
|||
![]()
In article >,
"Mel P." > wrote: > I replaced my starter with a 'new' rebuilt one... > When I turn the ignition, there's a grinding noise momentarily and then it > starts. > I removed it to check the flywheel gears and the starter gear look fine, no > shavings. > Is it possible the starter is bad? > > What else should I check? > > tia, could it be the bushing in the transaxle. or a bad bendix drive. best of luck. what was wrong with the previous starter? -- when you believe the only tool you have is a hammer. All problems look like nails. |
#3
|
|||
|
|||
![]()
The bushing is new. The starter looked OK, not bent
"A Veteran" > wrote in message ... > In article >, > "Mel P." > wrote: > >> I replaced my starter with a 'new' rebuilt one... >> When I turn the ignition, there's a grinding noise momentarily and then >> it >> starts. >> I removed it to check the flywheel gears and the starter gear look fine, >> no >> shavings. >> Is it possible the starter is bad? >> >> What else should I check? >> >> tia, > > could it be the bushing in the transaxle. or a bad bendix drive. > best of luck. what was wrong with the previous starter? > > -- > when you believe the only tool you have is a hammer. > All problems look like nails. |
#4
|
|||
|
|||
![]()
I have had noise when the engine spins with a new starter. The noise went
away after the new drive has worn to the flywheel teeth. "Mel P." > wrote in message ... > The bushing is new. The starter looked OK, not bent > > > "A Veteran" > wrote in message > ... > > In article >, > > "Mel P." > wrote: > > > >> I replaced my starter with a 'new' rebuilt one... > >> When I turn the ignition, there's a grinding noise momentarily and then > >> it > >> starts. > >> I removed it to check the flywheel gears and the starter gear look fine, > >> no > >> shavings. > >> Is it possible the starter is bad? > >> > >> What else should I check? > >> > >> tia, > > > > could it be the bushing in the transaxle. or a bad bendix drive. > > best of luck. what was wrong with the previous starter? > > > > -- > > when you believe the only tool you have is a hammer. > > All problems look like nails. > > |
#5
|
|||
|
|||
![]()
In article
>, A Veteran > wrote: > In article >, > "Mel P." > wrote: > > > I replaced my starter with a 'new' rebuilt one... > > When I turn the ignition, there's a grinding noise momentarily and then it > > starts. > > I removed it to check the flywheel gears and the starter gear look fine, no > > shavings. > > Is it possible the starter is bad? > > > > What else should I check? > > > > tia, > > could it be the bushing in the transaxle. or a bad bendix drive. > best of luck. what was wrong with the previous starter? the only time I've had a starter grind is when I used a 6 volt starter gear on 200 mm. flywheel. someone else changed it. could you have some mis-match? -- when you believe the only tool you have is a hammer. All problems look like nails. |
#6
|
|||
|
|||
![]()
> I replaced my starter with a 'new' rebuilt one...
> When I turn the ignition, there's a grinding noise momentarily and then it > starts. > I removed it to check the flywheel gears and the starter gear look fine, no > shavings. > Is it possible the starter is bad? Did you lubricate the bushing before you put the starter back in? Chris |
#7
|
|||
|
|||
![]()
I've changed the starter before in other cars and never heard this noise...
"Karl" > wrote in message ... >I have had noise when the engine spins with a new starter. The noise went > away after the new drive has worn to the flywheel teeth. > > > "Mel P." > wrote in message > ... >> The bushing is new. The starter looked OK, not bent >> >> >> "A Veteran" > wrote in message >> ... >> > In article >, >> > "Mel P." > wrote: >> > >> >> I replaced my starter with a 'new' rebuilt one... >> >> When I turn the ignition, there's a grinding noise momentarily and >> >> then >> >> it >> >> starts. >> >> I removed it to check the flywheel gears and the starter gear look > fine, >> >> no >> >> shavings. >> >> Is it possible the starter is bad? >> >> >> >> What else should I check? >> >> >> >> tia, >> > >> > could it be the bushing in the transaxle. or a bad bendix drive. >> > best of luck. what was wrong with the previous starter? >> > >> > -- >> > when you believe the only tool you have is a hammer. >> > All problems look like nails. >> >> > > |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
'02 Intrepid Starter Grinding Flywheel | msean | Chrysler | 18 | November 21st 06 06:40 PM |
Where to find my remote starter "box" | thomas | Technology | 3 | August 10th 06 12:22 AM |
Starter "Button" | Tom | Mazda | 18 | May 14th 06 04:00 AM |
Starter grinding noise when starting, after engine catches | [email protected] | Ford Explorer | 4 | May 6th 06 01:05 AM |