If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
1974 Dodge Dart - Hedmann Headers
I bought some hedman headers for my 74 dart and was able to put the
passenger side in without issue but am unable to install the drivers side. I can't seem to be able to get it passed the steering box. I've jacked the engine up with a floor jack but it still didn't have enough clearence. Any Suggestions would be greatly appreciated. |
Ads |
#2
|
|||
|
|||
Do they make a set with and without headers???
> wrote in message ... > I bought some hedman headers for my 74 dart and was able to put the > passenger side in without issue but am unable to install the drivers side. I > can't seem to be able to get it passed the steering box. I've jacked the > engine up with a floor jack but it still didn't have enough clearence. Any > Suggestions would be greatly appreciated. > > |
#3
|
|||
|
|||
Do they make a set with and without headers???
> wrote in message ... > I bought some hedman headers for my 74 dart and was able to put the > passenger side in without issue but am unable to install the drivers side. I > can't seem to be able to get it passed the steering box. I've jacked the > engine up with a floor jack but it still didn't have enough clearence. Any > Suggestions would be greatly appreciated. > > |
#4
|
|||
|
|||
They make shorty headers if that is what you where asking but they are 100
bucks more than the ones i already have. I was going to take the passenger side out again and see if that will allow me the needed clearence to put the driver side in..they may have to go in driverside first..worth a try. "maxpower" > wrote in message ... > Do they make a set with and without headers??? > > wrote in message > ... > > I bought some hedman headers for my 74 dart and was able to put the > > passenger side in without issue but am unable to install the drivers side. > I > > can't seem to be able to get it passed the steering box. I've jacked the > > engine up with a floor jack but it still didn't have enough clearence. Any > > Suggestions would be greatly appreciated. > > > > > > |
#5
|
|||
|
|||
They make shorty headers if that is what you where asking but they are 100
bucks more than the ones i already have. I was going to take the passenger side out again and see if that will allow me the needed clearence to put the driver side in..they may have to go in driverside first..worth a try. "maxpower" > wrote in message ... > Do they make a set with and without headers??? > > wrote in message > ... > > I bought some hedman headers for my 74 dart and was able to put the > > passenger side in without issue but am unable to install the drivers side. > I > > can't seem to be able to get it passed the steering box. I've jacked the > > engine up with a floor jack but it still didn't have enough clearence. Any > > Suggestions would be greatly appreciated. > > > > > > |
#6
|
|||
|
|||
no , what im asking is there a seperate part number if the vehicle has P/S.
I have a 67 Mustang that I put headers on and there was a special part number if the car had P/s, if it didnt have P/s it would have used a different part number > wrote in message ... > They make shorty headers if that is what you where asking but they are 100 > bucks more than the ones i already have. I was going to take the passenger > side out again and see if that will allow me the needed clearence to put the > driver side in..they may have to go in driverside first..worth a try. > > "maxpower" > wrote in message > ... > > Do they make a set with and without headers??? > > > wrote in message > > ... > > > I bought some hedman headers for my 74 dart and was able to put the > > > passenger side in without issue but am unable to install the drivers > side. > > I > > > can't seem to be able to get it passed the steering box. I've jacked the > > > engine up with a floor jack but it still didn't have enough clearence. > Any > > > Suggestions would be greatly appreciated. > > > > > > > > > > > > |
#7
|
|||
|
|||
no , what im asking is there a seperate part number if the vehicle has P/S.
I have a 67 Mustang that I put headers on and there was a special part number if the car had P/s, if it didnt have P/s it would have used a different part number > wrote in message ... > They make shorty headers if that is what you where asking but they are 100 > bucks more than the ones i already have. I was going to take the passenger > side out again and see if that will allow me the needed clearence to put the > driver side in..they may have to go in driverside first..worth a try. > > "maxpower" > wrote in message > ... > > Do they make a set with and without headers??? > > > wrote in message > > ... > > > I bought some hedman headers for my 74 dart and was able to put the > > > passenger side in without issue but am unable to install the drivers > side. > > I > > > can't seem to be able to get it passed the steering box. I've jacked the > > > engine up with a floor jack but it still didn't have enough clearence. > Any > > > Suggestions would be greatly appreciated. > > > > > > > > > > > > |
#8
|
|||
|
|||
|
#9
|
|||
|
|||
|
#10
|
|||
|
|||
On Mon, 17 Jan 2005 15:32:57 -0500, Sportster4Eva
> wrote: wrote: > >> I bought some hedman headers for my 74 dart and was able to put the >> passenger side in without issue but am unable to install the drivers side. I >> can't seem to be able to get it passed the steering box. I've jacked the >> engine up with a floor jack but it still didn't have enough clearence. Any >> Suggestions would be greatly appreciated. >> >> >Perhaps the drivers side needs to go in from the bottom up?? >A friend of mine had a '70 'Cuda and the drivers side was a real >P.I.T.A. to get. I think we had to unbolt the steering box to get the >drivers side in. Some headers came in 2 pieces for those Mopars and had >to be welded up after being bolted on... fun. >$.02 fwiw. I remember installing the headers on a '65 Valaiant 273 HyperPack. They went UP, then down through the fender wells. A real "nest os snakes". |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
1996 Dodge Grand Caravan LE AC/Heater Blower, Relay and Resistor Block Problems 101 | HeadlessHorseman | Dodge | 0 | January 5th 05 02:49 PM |
DODGE CHALLENGER: 340 HEADERS | emon | Dodge | 2 | September 16th 04 07:53 AM |