A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » Ford Explorer
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Explorer V8 EGR valve replacement



 
 
Thread Tools Display Modes
  #1  
Old February 26th 05, 07:49 PM
Dave Horoschak
external usenet poster
 
Posts: n/a
Default Explorer V8 EGR valve replacement

Does anyone know where I can find the instructions for replacing the EGR
valve in a 96 Explorer V8? None of the typical manuals (Chiltons,
Haynes) cover the V8 in enough detail for this to be included.

Thanks.
- Dave
  #2  
Old March 4th 05, 06:05 AM
Kevin D
external usenet poster
 
Posts: n/a
Default

Dave, which Haynes manual do you have? I have the1991 thru 2000 model year
manual. On page 6-26 is a pretty detailed procedure for R&R of the valve.

You only need to remove 2 bolts, a vacuum hose and the pipe retaining nut.
You might need to tap on the valve to break it loose. Once it's out, remove
the old gasket material. If the mounting flange is dirty, clean it with some
fine steel wool.

Use a new gasket (should come with the new valve). Replace the bolts, vac
hose and pipe, tighten everything up, and you're done.

Good luck,
Kevin

"Dave Horoschak" > wrote in message
...
> Does anyone know where I can find the instructions for replacing the EGR
> valve in a 96 Explorer V8? None of the typical manuals (Chiltons, Haynes)
> cover the V8 in enough detail for this to be included.
>
> Thanks.
> - Dave



  #3  
Old March 5th 05, 05:45 AM
Dave Horoschak
external usenet poster
 
Posts: n/a
Default

Yes - that's the same one I have. That section only covers the V6. The
whole EGR system on the V8 that I have is considerably different.
- Dave


Kevin D wrote:
> Dave, which Haynes manual do you have? I have the1991 thru 2000 model year
> manual. On page 6-26 is a pretty detailed procedure for R&R of the valve.
>
> You only need to remove 2 bolts, a vacuum hose and the pipe retaining nut.
> You might need to tap on the valve to break it loose. Once it's out, remove
> the old gasket material. If the mounting flange is dirty, clean it with some
> fine steel wool.
>
> Use a new gasket (should come with the new valve). Replace the bolts, vac
> hose and pipe, tighten everything up, and you're done.
>
> Good luck,
> Kevin
>
> "Dave Horoschak" > wrote in message
> ...
>
>>Does anyone know where I can find the instructions for replacing the EGR
>>valve in a 96 Explorer V8? None of the typical manuals (Chiltons, Haynes)
>>cover the V8 in enough detail for this to be included.
>>
>>Thanks.
>> - Dave

>
>
>

  #4  
Old March 6th 05, 06:16 PM
Kevin D
external usenet poster
 
Posts: n/a
Default

Yes, you're correct - I assumed that the valve would be the same regardless
of engine. I'm surprised that it is different. I've replaced EGR valves on
my cars starting with a '78 Chevy that I bought new, and they've all been
essentially the same - two bolts at the base, and a vac line to the
diaphragm. Not all have had a pipe, tho.

Sorry I can't be more helpful!

Kevin

"Dave Horoschak" > wrote in message
...
> Yes - that's the same one I have. That section only covers the V6. The
> whole EGR system on the V8 that I have is considerably different.
> - Dave
>
>
> Kevin D wrote:
>> Dave, which Haynes manual do you have? I have the1991 thru 2000 model
>> year manual. On page 6-26 is a pretty detailed procedure for R&R of the
>> valve.
>>
>> You only need to remove 2 bolts, a vacuum hose and the pipe retaining
>> nut. You might need to tap on the valve to break it loose. Once it's
>> out, remove the old gasket material. If the mounting flange is dirty,
>> clean it with some fine steel wool.
>>
>> Use a new gasket (should come with the new valve). Replace the bolts,
>> vac hose and pipe, tighten everything up, and you're done.
>>
>> Good luck,
>> Kevin
>>
>> "Dave Horoschak" > wrote in message
>> ...
>>
>>>Does anyone know where I can find the instructions for replacing the EGR
>>>valve in a 96 Explorer V8? None of the typical manuals (Chiltons,
>>>Haynes) cover the V8 in enough detail for this to be included.
>>>
>>>Thanks.
>>> - Dave

>>
>>


  #5  
Old December 8th 17, 02:18 AM posted to rec.autos.makers.ford.explorer
runbeguy9000
external usenet poster
 
Posts: 1
Default Explorer V8 EGR valve replacement

replying to Kevin D, runbeguy9000 wrote:
i have the 2002 and up hopwever i havent found 1 that covers the 2001 v8 (XLT)
version.
im trying tom repklace the erg in mine.

--
for full context, visit http://www.motorsforum.com/ford-expl...ent-11026-.htm


  #6  
Old March 14th 05, 07:55 AM
Frank
external usenet poster
 
Posts: n/a
Default

"Dave Horoschak" wrote:
> Does anyone know where I can find the instructions for
> replacing the EGR
> valve in a 96 Explorer V8? None of the typical manuals
> (Chiltons,
> Haynes) cover the V8 in enough detail for this to be included.
>
> Thanks.
> - Dave


I had my EGR valve, EGR sensor and the Vaccum control valve on my 96
V8 Explorer replaced by the dealer and it cost over $300. I felt
ripped off. Since I requested my original parts to be saved, I feel
confident in doing it myself next time.

The following the is the procedure that I would use. Buy parts or
examine the parts used. From this examination it can be seen that the
EGR sensor mounts on the back of the EGR value by three small nuts.
Before starting I WOULD DISCONNECT THE BATTERY FIRST. I would
carefully remove these three nuts first and then remove the electrical
connector from the sensor(because it is held top and bottom by the
electrical connector’s slip clips, I see that I can’t easily get to
the lower clip when the sensor is mounted on the back of the EGR
Valve). Although the quarters are tight, the bottom retaining bolt or
nut on the EGR Valve should be now be accessible with either a
universal joint/socket combination or a special purpose wrench. After
removing the EGR valve and cleaning the surface. The installation of a
new EGR could be done in reverse order. I would attach the electrical
cable to the EGR sensor after it is mounted to the back of the EGR
valve. This way should allow me more room to install the three small
EGR sensor nuts. Although, I haven’t performed the above installation
myself this is the approach I would use if my EGR valve needs
replacement again.

--
Posted using the http://www.autoforumz.com interface, at author's request
Articles individually checked for conformance to usenet standards
Topic URL: http://www.autoforumz.com/Ford-Explo...ict105117.html
Visit Topic URL to contact author (reg. req'd). Report abuse: http://www.autoforumz.com/eform.php?p=501079
  #7  
Old March 15th 05, 01:34 AM
phoeneous
external usenet poster
 
Posts: n/a
Default

"Frank" wrote:
> I had my EGR valve, EGR sensor and the Vaccum control valve on
> my 96 V8 Explorer replaced by the dealer and it cost over
> $300. I felt ripped off. Since I requested my original parts
> to be saved, I feel confident in doing it myself next time.
>
> The following the is the procedure that I would use. Buy parts
> or examine the parts used. From this examination it can be
> seen that the EGR sensor mounts on the back of the EGR value
> by three small nuts. Before starting I WOULD DISCONNECT THE
> BATTERY FIRST. I would carefully remove these three nuts first
> and then remove the electrical connector from the
> sensor(because it is held top and bottom by the electrical
> connector's slip clips, I see that I can't easily get to the
> lower clip when the sensor is mounted on the back of the EGR
> Valve). Although the quarters are tight, the bottom retaining
> bolt or nut on the EGR Valve should be now be accessible with
> either a universal joint/socket combination or a special
> purpose wrench. After removing the EGR valve and cleaning the
> surface. The installation of a new EGR could be done in
> reverse order. I would attach the electrical cable to the EGR
> sensor after it is mounted to the back of the EGR valve. This
> way should allow me more room to install the three small EGR
> sensor nuts. Although, I haven't performed the above
> installation myself this is the approach I would use if my EGR
> valve needs replacement again.


I need to clean my EGR valve because it is blocked. Im not sure where
it is under my hood but this is the most similar part compared to most
others.

So, is this my EGR Valve?

http://www.photohost.org/gallery/dat...92egrfront.jpg

http://www.photohost.org/gallery/dat...92egrright.jpg

http://www.photohost.org/gallery/data/500/92egrleft.jpg
  #8  
Old March 15th 05, 03:22 AM
Fred 2
external usenet poster
 
Posts: n/a
Default

No it is not, that part is a vaccum operated water valve for the
heater.

On 14 Mar 2005 19:34:56 -0500, phoeneous >
wrote:


>
>So, is this my EGR Valve?
>
>http://www.photohost.org/gallery/dat...92egrfront.jpg
>
>http://www.photohost.org/gallery/dat...92egrright.jpg
>
>http://www.photohost.org/gallery/data/500/92egrleft.jpg


  #9  
Old March 15th 05, 10:18 PM
phoeneous
external usenet poster
 
Posts: n/a
Default

"Fred 2" wrote:
> No it is not, that part is a vaccum operated water valve for
> the
> heater.
>
> On 14 Mar 2005 19:34:56 -0500, phoeneous
> >
> wrote:
>
>
> >
> >So, is this my EGR Valve?
> >
> >http://www.photohost.org/gallery/dat...92egrfront.jpg
> >
> >http://www.photohost.org/gallery/dat...92egrright.jpg
> >
> >http://www.photohost.org/gallery/data/500/92egrleft.jpg


Fred, can you edit the pics I posted and point to the area you are
referring to? Im confused

--
Posted using the http://www.autoforumz.com interface, at author's request
Articles individually checked for conformance to usenet standards
Topic URL: http://www.autoforumz.com/Ford-Explo...ict105117.html
Visit Topic URL to contact author (reg. req'd). Report abuse: http://www.autoforumz.com/eform.php?p=502406
  #10  
Old March 16th 05, 02:19 AM
Fred 2
external usenet poster
 
Posts: n/a
Default


Go the the URL below and look at the 2 scans and the captions below
them

http://ourplaceusa.home.att.net/egr.htm

On 15 Mar 2005 16:18:48 -0500, phoeneous
>
>Fred, can you edit the pics I posted and point to the area you are
>referring to? Im confused


 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
rec.autos.makers.chrysler FAQ, Part 1/6 Dr. David Zatz Chrysler 3 February 18th 05 06:34 AM
1997 ford explorer starter replacement explorerguy Ford Explorer 1 February 14th 05 01:39 AM
C5 problems (98 in particular) radar Corvette 12 January 3rd 05 11:04 PM
Replacement bolt size for Thermostat outlet 94 Explorer XLT Herb Patterson Ford Explorer 1 November 10th 04 03:22 AM
96 Explorer Center Console Cover Replacement BillyforExplorers Ford Explorer 0 November 9th 04 05:49 PM


All times are GMT +1. The time now is 10:25 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.