If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
SL2 sticky throttle problem
The throttle accelerator pedal on my '92 Saturn SL2 seemed to be
sticking so that when you stopped at a traffic light, the idle rpm might be at 2-3K before slowly dropping back down to idle speed after 30 or 40 seconds. The pedal and cable linkage were fine. The 'Service Engine Soon' light did not come on. Googling the problem suggested that the the throttle body might be gummed so disassembled and cleaned it but the problem was still the same. The throttle body had a little solenoid valve and piston attached to it that opened and closed a little bypass hole around the throttle body butterfly valve. Turns out that is the 'air idle control valve' or AICV and it adjusts to control the flow of air through a little hole about 1/4" in diameter that provides the air to the engine for idling when the throttle butterfly is closed. I didn't think it could be bad because there was no fault code or SES light but I decided to change it as there wasn't much else that could be causing the problem. Et voila! The problem was solved. What puzzles me is why there wasn't a fault code for the AICV function. My guess is that the Saturn doesn't throw a fault code if the idle rpm doesn't drop back down like it's supposed to perhaps because the programming is set to maintain MINIMUM idle rpm and only issue a code when the idle rpm is below that. At higher rpm, the throttle butterfly is supposed to be open and the AICV closed but the computer has no way of knowing that the AICV was failing to close. The computer should have thrown a fault code when the throttle position was closed and the idle speed was too fast but the car is a manual transmission so the rpms stay up to correspond to the road speed even when you back off of the gas so the computer didn't know the car was 'idling' rather that 'driving.' The computers on newer OBD2 vehicles know what the vehicle speed is but apparently the OBD1 Saturns don't report the vehicle speed to the computer. -- Posted with OS/2 Warp 4.52 and Sea Monkey 1.5a |
Ads |
#2
|
|||
|
|||
SL2 sticky throttle problem
"David T. Johnson" > wrote in message diainc... > The throttle accelerator pedal on my '92 Saturn SL2 seemed to be sticking > so that when you stopped at a traffic light, the idle rpm might be at 2-3K > before slowly dropping back down to idle speed after 30 or 40 seconds. > The pedal and cable linkage were fine. The 'Service Engine Soon' light > did not come on. Googling the problem suggested that the the throttle > body might be gummed so disassembled and cleaned it but the problem was > still the same. The throttle body had a little solenoid valve and piston > attached to it that opened and closed a little bypass hole around the > throttle body butterfly valve. Turns out that is the 'air idle control > valve' or AICV and it adjusts to control the flow of air through a little > hole about 1/4" in diameter that provides the air to the engine for idling > when the throttle butterfly is closed. I didn't think it could be bad > because there was no fault code or SES light but I decided to change it as > there wasn't much else that could be causing the problem. Et voila! The > problem was solved. > > What puzzles me is why there wasn't a fault code for the AICV function. My > guess is that the Saturn doesn't throw a fault code if the idle rpm > doesn't drop back down like it's supposed to perhaps because the > programming is set to maintain MINIMUM idle rpm and only issue a code when > the idle rpm is below that. At higher rpm, the throttle butterfly is > supposed to be open and the AICV closed but the computer has no way of > knowing that the AICV was failing to close. The computer should have > thrown a fault code when the throttle position was closed and the idle > speed was too fast but the car is a manual transmission so the rpms stay > up to correspond to the road speed even when you back off of the gas so > the computer didn't know the car was 'idling' rather that 'driving.' The > computers on newer OBD2 vehicles know what the vehicle speed is but > apparently the OBD1 Saturns don't report the vehicle speed to the > computer. > David, Thanks for posting this. I have a very similar problem as I posted last month. (post copied below) Mine is an OBD11 car with similar symptoms as yours. Shortly after my posting the SES light came on, so I did a scan which returned a code ISO9141, which nobody could identify??? On rescan I got a code PO147. I cleared the PCM and SES light did not reappear. It was suggested to me that I may have an IAC valve problem similar to yours and my reading and your timely post seem to confirm that this is the area needing further inspection and service. Did you attempt to clean the IAC valve or just replace it? Cost of new part? The scan code ISO9141 was confusing but goggle returned http://www.obd-codes.com/faq/obd-ii-protocols.php I suspect this is important information when purchasing a code reader. My error searches found - P0147=Heated Oxygen Sensor HO2S Heater Circuit Malfunction (Bank 1 Sensor 3) M/T Only I do not understand what this may indicate? The only O2 sensor I am aware of is in the exhaust and it does not have a specific heater circuit. I had suspected that this may indicate faulty CTS? but now think it more likely that a malfunctioning IAC valve may be causing a false reading from the O2 sensor. Why would this be 'M/T Only'? I will admit that I have been procrastinating the service somewhat as the car is still very usable and I would prefer warmer weather for any repair, and it is not uncommon for many problems to disappear in the spring. I think that this is a good example of how a little research and DIY mechanicing can eliminate the reliance on dealer service and save a lot of $$ and aggravation and disappointment. It does require a bit of learning effort but neither the work or the systems are all that complicated and IMHO learning is a big part of life. I am grateful for this NG and all who contribute here. Happy trails to all. > > "Private" > wrote in message > ... >> Purchased new, 1996, SW1, 5sp manual, 310000km. >> no ses light (previous intermittent ses light problems solved by changing >> fuel cap) >> >> Car starts and runs fine, no other problems noticed. Fuel consumption >> rate may? be very slightly increased (not obviously excessive) but it is >> hard to tell as consumption is usually slightly higher in winter. >> >> At start-up, the engine initially runs at ~15-1700 rpm for 10-20 seconds >> before reducing to regular idle speed. >> >> When car is stopped, and engine is warm, if engine speed is increased to >> +2000 rpm and then throttle is closed, the engine is slow to return to >> regular idle speed. >> >> Throttle linkage and return springs checked, OK. >> >> I have never used intake or injector cleaners and have never needed to >> work on intake or fuel system other than fuel and air filter changes. >> >> Could this be a dribbling or leaking fuel injector? Warm engine idle is >> smooth. >> >> TIA >> "Bob Shuman" > wrote in message ... >I would suspect a bad coolant temperature sensor (CTS). This is a $10 part >and 5 minutes effort to change it. > > Bob Bob, Thanks for this suggestion, I had forgotten that replacing the CTS seems to solve most similar problems reported here. |
#3
|
|||
|
|||
SL2 sticky throttle problem
Private wrote:
> > I have a very similar problem as I posted last month. (post copied below) > > Mine is an OBD11 car with similar symptoms as yours. Shortly after my > posting the SES light came on, so I did a scan which returned a code > ISO9141, which nobody could identify??? On rescan I got a code PO147. I > cleared the PCM and SES light did not reappear. It was suggested to me that > I may have an IAC valve problem similar to yours and my reading and your > timely post seem to confirm that this is the area needing further inspection > and service. > > Did you attempt to clean the IAC valve or just replace it? > Cost of new part? I just replaced it. I got one at Car Quest for $50. It took about 30 minutes to remove the throttle body, replace the valve, and reinstall it. Youtube has a good video on removing the throttle body on the Saturn S series. > > The scan code ISO9141 was confusing but goggle returned > http://www.obd-codes.com/faq/obd-ii-protocols.php > I suspect this is important information when purchasing a code reader. > > My error searches found - P0147=Heated Oxygen Sensor HO2S Heater Circuit > Malfunction (Bank 1 Sensor 3) M/T Only > I do not understand what this may indicate? The only O2 sensor I am aware > of is in the exhaust and it does not have a specific heater circuit. I had > suspected that this may indicate faulty CTS? but now think it more likely > that a malfunctioning IAC valve may be causing a false reading from the O2 > sensor. Why would this be 'M/T Only'? It's always possible that there is more than one malfunction. The overspeed 'sticky throttle' idle, though, is a dead giveaway for the IAC valve if the throttle body butterfly valve is clean and working properly since the only other way for air to get into the intake is through the IAC port (assuming that there aren't any obvious vacuum leaks). -- Posted with OS/2 Warp 4.52 and Sea Monkey 1.5a |
#4
|
|||
|
|||
SL2 sticky throttle problem
"David T. Johnson" > wrote in message diainc... > Private wrote: > >> >> I have a very similar problem as I posted last month. (post copied >> below) >> >> Mine is an OBD11 car with similar symptoms as yours. Shortly after my >> posting the SES light came on, so I did a scan which returned a code >> ISO9141, which nobody could identify??? On rescan I got a code PO147. I >> cleared the PCM and SES light did not reappear. It was suggested to me >> that I may have an IAC valve problem similar to yours and my reading and >> your timely post seem to confirm that this is the area needing further >> inspection and service. >> >> Did you attempt to clean the IAC valve or just replace it? >> Cost of new part? > > I just replaced it. I got one at Car Quest for $50. It took about 30 > minutes to remove the throttle body, replace the valve, and reinstall it. > Youtube has a good video on removing the throttle body on the Saturn S > series. > >> >> The scan code ISO9141 was confusing but goggle returned >> http://www.obd-codes.com/faq/obd-ii-protocols.php >> I suspect this is important information when purchasing a code reader. >> >> My error searches found - P0147=Heated Oxygen Sensor HO2S Heater Circuit >> Malfunction (Bank 1 Sensor 3) M/T Only >> I do not understand what this may indicate? The only O2 sensor I am >> aware of is in the exhaust and it does not have a specific heater >> circuit. I had suspected that this may indicate faulty CTS? but now >> think it more likely that a malfunctioning IAC valve may be causing a >> false reading from the O2 sensor. Why would this be 'M/T Only'? > > It's always possible that there is more than one malfunction. The > overspeed 'sticky throttle' idle, though, is a dead giveaway for the IAC > valve if the throttle body butterfly valve is clean and working properly > since the only other way for air to get into the intake is through the IAC > port (assuming that there aren't any obvious vacuum leaks). IAC & throttle body cleaned. (New valve price 80-105 C$) Problem solved, total cost <10$ for carb cleaner and gasket. Thanks for help and advice. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Solution - E46 330ci sticky throttle, power surge, step change in power, unpredictable acceleration | Pashlipops | BMW | 3 | June 26th 06 08:42 AM |
Mystery Throttle Problem | Thomas Koschate | VW water cooled | 4 | October 10th 05 04:55 AM |
RBR throttle problem | Txl | Simulators | 1 | August 16th 05 04:58 PM |
A4 2.5 tdi throttle problem | LostJonnnie | Audi | 13 | March 31st 05 05:58 PM |
Stiff/sticky throttle | Crunchy Cookie | Honda | 10 | November 25th 04 03:26 AM |