A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto newsgroups » Antique cars
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

1960 Ford Falcon



 
 
Thread Tools Display Modes
  #1  
Old July 8th 08, 02:22 AM posted to alt.autos.antique,rec.autos.antique
rbrooks
external usenet poster
 
Posts: 1
Default 1960 Ford Falcon

Is anyone familiar with the most likely cause of the number 1 cylinder
to loose compression in the 4.6 straight 6?

--
Posted at author's request, using moderated http://www.AutoBoardz.com interface
Thread archive: http://www.AutoBoardz.com/1960-Ford-...ict248003.html
Ads
  #3  
Old July 8th 08, 04:04 AM posted to alt.autos.antique,rec.autos.antique
George Patterson
external usenet poster
 
Posts: 82
Default 1960 Ford Falcon

rbrooks wrote:
> Is anyone familiar with the most likely cause of the number 1 cylinder
> to loose compression in the 4.6 straight 6?


I'm not familiar with a 4.6 straight 6. The Falcon came with either a 144 CID or
a 170 CID straight 6, and I'm not sure that the 170 was available in 1960. I am
familiar with these, having owned several.

There are a variety of possibilities - blown head gasket, warped cylinder head,
blown-out spark plug, bad plug gasket, broken or worn rings, and burnt valves
are some I can think of. The blown-out plug is the least likely and most easily
detected, so we can probably rule that out. Still, since it's the easiest thing
to deal with, check that first. Do this by replacing the plug and gasket, making
sure you tighten it properly. A blow-out plug won't tighten up.

Put a compression gauge on the cylinder, pull the coil wire, crank the engine
around by hand to TDC, and listen. If you hear air escaping into the exhaust
system, this is almost certainly a burnt exhaust valve. IMO, this is the most
likely. If you hear air escaping into the intake manifold, the intake valve is
defective (probably cracked). If you don't hear air escaping but the compression
falls, it's likely rings or head problems.

Bad rings generally cause excessive oil consumption, so that's one thing to look
for. The oil frequently blows out the vent, rather than being burned, so you
will see drips of oil on the driveway, and the lower part of the engine will be
covered with a film. The oil breather on the car is a downtube on the right
front of the engine. That's where most of the excess will blow out, but also
check the filler cap.

A blown head gasket will frequently put gases into the cooling channels. To
check for this, warm the engine up with the radiator cap removed. You will be
able to tell when the thermostat opens up from the increase in water flow. If
you see a flow of bubbles in the coolant coming out of the upper hose, you have
a blown gasket.

The same symptoms may show up for a warped cylinder head or block. This is
usually caused by overheating. The only way I know to check this is to remove
the head and have a machine shop check both the head and block for flatness.
Whatever the cause, you will probably wind up doing this step as part of the
rebuild anyway.

The last items will be a cracked head or block. Cracked heads are difficult to
diagnose without disassembly, but these can be repaired. The old engines are
cast iron, and cracks can be plugged or welded.

George Patterson
Decisions are made by people who have time, not by people who have talent.
Talented people are too busy fixing problems created by people who make
decisions.
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Repost for MSJJ: 1960 Ford Falcon.jpg 83357 bytes HEMI-Powered@[email protected] Auto Photos 15 March 8th 08 10:36 PM
Repost for MSJJ: 1964 Ford Falcon Sprint modified sml blk Ford engine.JPG 311766 bytes HEMI-Powered@[email protected] Auto Photos 0 March 8th 08 03:55 AM
Repost by request: 1964 Ford Falcon Sprint modified sml blk Ford engine.JPG 311766 bytes HEMI-Powered@[email protected] Auto Photos 0 March 8th 08 12:48 AM
Repost by request: 1960 Ford Falcon Advertisement.jpg 75809 bytes HEMI-Powered@[email protected] Auto Photos 0 March 8th 08 12:37 AM
63 Ford Falcon Melissa Murphy Antique cars 2 July 20th 04 04:12 PM


All times are GMT +1. The time now is 12:37 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.