A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » VW air cooled
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Kadron h40/44 eis accelerator check ball



 
 
Thread Tools Display Modes
  #1  
Old May 4th 15, 12:17 AM posted to rec.autos.makers.vw.aircooled
Larry Q
external usenet poster
 
Posts: 2
Default Kadron h40/44 eis accelerator check ball

Hi all ,
I'm trying to rebuild a set of solex kadron h40/44 eis carbs. I was getting no
gas when i moved the linkage or accelarator diafame. I pulled the nut that
shold have held the check ball for accelerator circuit .I used a 4 mm long
screw and stop came out. inside there was no ball but it did have small
plastic piece that was fit into the opening and seems to have a resess for a
ball.Not sure who or when last rebuild was. Does anyone know if this ball
bearing is the same size as one under the squirter tube. thanks


--
posted from
http://www.motorsforum.com/volkswage...all-77342-.htm
using MotorsForum's Web, RSS and Social Media Interface to
rec.autos.makers.vw.aircooled and other automotive groups

Ads
  #2  
Old May 14th 15, 11:18 PM posted to rec.autos.makers.vw.aircooled
Larry Q
external usenet poster
 
Posts: 2
Default Kadron h40/44 eis accelerator check ball

replying to Larry Q, Larry Q wrote:
> Larry Q wrote:
>
> Hi all ,
> I'm trying to rebuild a set of solex kadron h40/44 eis carbs. I was getting

no
> gas when i moved the linkage or accelarator diafame. I pulled the nut that

shold
> have held the check ball for accelerator circuit .I used a 4 mm long screw

and
> stop came out. inside there was no ball but it did have small plastic piece

that
> was fit into the opening and seems to have a resess for a ball.Not sure who

or
> when last rebuild was. Does anyone know if this ball bearing is the same

size as
> one under the squirter tube. thanks



Just an update after pulling other carb apart found same small plastic piece
init. Best discription is like old golf tee. My carbs had come from So Cal in
1998 looked like they had never been apart. Still had the paint on the inlet
screw and gas filter screw . So I guess some where the ball was swapped for
these plastic pieces. Well carbs are back now just playing with fine adj.


--
posted from
http://www.motorsforum.com/volkswage...all-77342-.htm
using MotorsForum's Web, RSS and Social Media Interface to
rec.autos.makers.vw.aircooled and other automotive groups

 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Need HELP REAL BAD with dual KADRON carbs setup please...... [email protected] VW air cooled 0 July 23rd 12 03:16 PM
Kadron Carburetors-Question Doug[_5_] VW air cooled 1 May 14th 07 06:41 AM
ball valve,check valve,globe valve, [email protected] Alfa Romeo 0 March 1st 06 04:11 AM
why does Kadron sound so much like crap? Hartmann VW air cooled 1 April 23rd 05 01:47 AM
Help with Kadron/Solex 40 dual carbs volksbuggydriver VW air cooled 2 October 16th 04 08:31 PM


All times are GMT +1. The time now is 04:28 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright 2004-2018 AutoBanter.
The comments are property of their posters.