If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
XJ floorboard holes
As I mentioned in a previous post, I have a couple of holes to repair
in the passenger side floorboard of my XJ... What is the best way to repair this? 1. Weld replacement sheet metal over the holes. 2. Rivet replacement sheet metal over the holes and fiberglass around the edges so that it will be air tight. 3. Forget about metal and just fiberglass the holes. The larger hole is over the muffler, so I'm not sure if the fiberglass-only method would withstand the heat... |
Ads |
#2
|
|||
|
|||
XJ floorboard holes
"Grumman-581" > wrote in message
... > As I mentioned in a previous post, I have a couple of holes to repair > in the passenger side floorboard of my XJ... What is the best way to > repair this? > > 1. Weld replacement sheet metal over the holes. > 2. Rivet replacement sheet metal over the holes and fiberglass around > the edges so that it will be air tight. > 3. Forget about metal and just fiberglass the holes. > > The larger hole is over the muffler, so I'm not sure if the > fiberglass-only method would withstand the heat... Fiberglass is rigid and will separate from the metal, holding water against the metal, and then you will have a worse situation than you have now. Welding is best. Pop-rivets may be acceptable, depending on the nature of the holes and skill of repair. Forget about fiberglass and get some seam sealer from a body shop supply. Acceptable replacements are available at Home Depot. Urethane in a tube is great. Earle |
#3
|
|||
|
|||
XJ floorboard holes
Grumman-581 wrote:
> As I mentioned in a previous post, I have a couple of holes to repair > in the passenger side floorboard of my XJ... What is the best way to > repair this? > > 1. Weld replacement sheet metal over the holes. > 2. Rivet replacement sheet metal over the holes and fiberglass around > the edges so that it will be air tight. > 3. Forget about metal and just fiberglass the holes. > > The larger hole is over the muffler, so I'm not sure if the > fiberglass-only method would withstand the heat... To be perfectly candid, all of those repair suggestions are kinda half-assed and will cause you problems down the road. It depends on the value of the truck and what you want to spend in time and money. The ONLY way to get rid of rust is to cut out the rusty floorboards and spot weld in new panels. Any sort of patch job is guaranteed to rust again. tw -- PLEASE REMOVE THE "OBVIOUS" TO REPLY. |
#4
|
|||
|
|||
XJ floorboard holes
http://www.billhughes.com/snowXJ/ Spot weld the plates in, it doesn't
take much to shrink to the point where the door won't close. God Bless America, Bill O|||||||O http://www.billhughes.com/ "Grumman-581" > wrote in message ... > As I mentioned in a previous post, I have a couple of holes to repair > in the passenger side floorboard of my XJ... What is the best way to > repair this? > > 1. Weld replacement sheet metal over the holes. > 2. Rivet replacement sheet metal over the holes and fiberglass around > the edges so that it will be air tight. > 3. Forget about metal and just fiberglass the holes. > > The larger hole is over the muffler, so I'm not sure if the > fiberglass-only method would withstand the heat... -- Posted via a free Usenet account from http://www.teranews.com |
#5
|
|||
|
|||
XJ floorboard holes
be carefull since the floor metal is attached to the frame rails and that
is what makes it survive a crash so include reinfocing that alongwith the holes Grumman-581 wrote: > As I mentioned in a previous post, I have a couple of holes to repair > in the passenger side floorboard of my XJ... What is the best way to > repair this? > > 1. Weld replacement sheet metal over the holes. > 2. Rivet replacement sheet metal over the holes and fiberglass around > the edges so that it will be air tight. > 3. Forget about metal and just fiberglass the holes. > > The larger hole is over the muffler, so I'm not sure if the > fiberglass-only method would withstand the heat... |
#6
|
|||
|
|||
XJ floorboard holes
just did mine a few years ago.
Be carefull as you clean/ grind the areas mine was a disaster!!!!!!!!!! More rust than first thought!! Get 20G steel from local sheet metal place, rent , borrow, or (this is a good excuse for a MIG welder purchase, how I justified mine to my wife). Make cardboard templates and then cut the sheet metal and fit into place and spot weld in best you can (tough to weld all of the area but possible). Get some SEAM SEALER and go over welds and seams top and bottom. Get some POR15 and brush on top and bottom after sealer dries and good to go. For some reason the passenger rust out bad compared to driver with moisture still present, check tube that extends from door to body with the wires in it and make sure no water gets in behind cowl. Good time to remove all the carpet and padding and give a good cleaning. Watch out if using cutting wheel and or grinding that the sparks damage roof liner and or any glass like the windshield doors etc... Good luck about 3 beers *** skill level.. "philthy" > wrote in message ... > be carefull since the floor metal is attached to the frame rails and that > is what makes it survive a crash so include reinfocing that alongwith the > holes > > Grumman-581 wrote: > >> As I mentioned in a previous post, I have a couple of holes to repair >> in the passenger side floorboard of my XJ... What is the best way to >> repair this? >> >> 1. Weld replacement sheet metal over the holes. >> 2. Rivet replacement sheet metal over the holes and fiberglass around >> the edges so that it will be air tight. >> 3. Forget about metal and just fiberglass the holes. >> >> The larger hole is over the muffler, so I'm not sure if the >> fiberglass-only method would withstand the heat... > |
#7
|
|||
|
|||
XJ floorboard holes
On Sun, 3 Jun 2007 17:15:10 -0400, "TF" >
wrote: > Get 20G steel from local sheet metal place Thanks for the info... My *next* question was going to be concerning the appropriate gauge sheet metal to use... I was at a commercial construction site today and they were doing the interior walls with the sheet metal 2x6s... They were cutting off pieces from 4-6 ft in length and throwing them in the dumpster... Seemed about the right thickness, so I picked up a couple of them... At the very least, it will give me plenty of metal to practice on before I go burning holes in the floor pan of my XJ... > Good luck about 3 beers *** skill level.. That 3 beers per hour, right? |
#8
|
|||
|
|||
XJ floorboard holes
Grumman-581 wrote:
>... At the very least, it > will give me plenty of metal to practice on before I go burning holes > in the floor pan of my XJ... I'd be picking up all the scrap they have to offer just for that reason alone. Throwing a good weld is all in the practice. especially with gas where you can blow through thin metal. Thankfully MIGs are more forgiving. Of course now you will need a good plasma cutter. -- DougW |
#9
|
|||
|
|||
XJ floorboard holes
damn...forgot about the plasma cutter..than again I wanted tig too but
settled for gas option with the mig... live and learn next project! "DougW" > wrote in message ... > Grumman-581 wrote: >>... At the very least, it >> will give me plenty of metal to practice on before I go burning holes >> in the floor pan of my XJ... > > I'd be picking up all the scrap they have to offer just for that reason > alone. Throwing a good weld is all in the practice. especially with gas > where you can blow through thin metal. Thankfully MIGs are more > forgiving. > > Of course now you will need a good plasma cutter. > > -- > DougW > |
#10
|
|||
|
|||
XJ floorboard holes
On Jun 4, 4:02 am, Grumman-581 >
wrote: > On Sun, 3 Jun 2007 17:15:10 -0400, "TF" > > wrote: > > > Get 20G steel from local sheet metal place > > Thanks for the info... My *next* question was going to be concerning > the appropriate gauge sheet metal to use... I was at a commercial > construction site today and they were doing the interior walls with > the sheet metal 2x6s... They were cutting off pieces from 4-6 ft in > length and throwing them in the dumpster... Seemed about the right > thickness, so I picked up a couple of them... At the very least, it > will give me plenty of metal to practice on before I go burning holes > in the floor pan of my XJ... > > > Good luck about 3 beers *** skill level.. > > That 3 beers per hour, right? I may be wrong but I think those steel 2X6s are galvanized. If you are going to use them for welding make sure you have reallly good ventilation. Don't want to poision yourself! John C. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
XJ air-conditioner leak on passenger floorboard | [email protected] | Jeep | 2 | May 24th 07 01:52 PM |
XJ air-conditioner leak on passenger floorboard | Grumman-581 | Jeep | 9 | May 24th 07 04:20 AM |
water on floorboard | k1orca | Chrysler | 1 | August 26th 06 05:53 AM |
Water coming out of blower in floorboard | JeepXJ | Jeep | 1 | August 11th 06 12:50 AM |
Drain holes | ISando | Mazda | 0 | November 17th 04 02:06 PM |