If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
ADVICE NEEDED: Removing Inner Tie Rod Ends - TWO QUESTIONS
I am going to start replacing the worn tie rod ends (inner and outer) and ball joints in my 1996 Mustang GT. I have heard that the inner tie rod ends that originally came with my car are screwed onto the ends of the steering rack and then held in place by a small pin. How do I remove this pin? Is it soft enough to simply shear off if I start to unscrew the old inner tie rod ends? Do I have to drill this pin out? Is there some "proper" way of removing this pin? My new replacement TRW inner tie rod ends don't need a pin to hold them in place, so I only need to worry about the pins when I remove the old inner tie rod ends. But I need a fool-proof method of being able to grab and remove these pins....I would hate to get STUCK halfway through the repair! Here's another thing that worries me.... The instructions that came with my new TRW inner tie rod ends mention have this caution: "CAUTION - Always hold the rack from turning by using an adjustable wrench on the flat of the teeth on the rack. This must be done when removing inner socket on each side. Failure to do so will cause the rack teeth and the pinion teeth to wedge against each other as the pinion tries to prevent the rack from rotating. This could result in chipped, cracked, or broken teeth which will cause erratic steering and binding of the steering assembly." HUH?!? My Haynes manual makes no mention of this "hazard". But then again, the Haynes manual only gives instructions for replacing the entire steering gear. (I won't be owning this car for very much longer, so I am not that interested in buying an entire replacement steering gear. I would just as soon replace only the inner tie rod ends. My current steering gear works great and has no leaks.) I had assumed that removing and replacing the inner tie rod ends would be a fairly straightforward "unscrew and re-screw" procedure. Why would I need to brace the rack? Will I really be required to apply that much torque to it to remove and install the inner tie rod ends? I don't even think I have heard anyone on these newsgroups mention having to brace the rack. What the heck are they talking about here??? I should point out that I completely rebuilt the front steering and suspension on my 1965 Mustang. But that car has manual steering, not power steering. My 1996 GT has power steering, and I have to say that I have never really messed with any power steering components, so I am more than a bit cautious at this stage. Any help, advice, tips, or other information would be most welcome! Thanks in advance...... |
Ads |
#2
|
|||
|
|||
ADVICE NEEDED: Removing Inner Tie Rod Ends - TWO QUESTIONS
"EADGBE" > wrote in message ... > > I am going to start replacing the worn tie rod ends (inner and outer) > and ball joints in my 1996 Mustang GT. > > HUH?!? My Haynes manual makes no mention of this "hazard". But then > again, the Haynes manual only gives instructions for replacing the > entire steering gear. (I won't be owning this car for very much > longer, so I am not that interested in buying an entire replacement > steering gear. I would just as soon replace only the inner tie rod > ends. My current steering gear works great and has no leaks.) > Since your going to be selling it soon, why are you bothering with this? Your not going to get squat in enhanced resale value by doing this repair yourself. IMHO the only people who should be buying inner tie rods are the steering rack rebuild houses. Ted |
#3
|
|||
|
|||
ADVICE NEEDED: Removing Inner Tie Rod Ends - TWO QUESTIONS
On Jun 26, 6:09 am, "Ted Mittelstaedt" > wrote:
> > Since your going to be selling it soon, why are you bothering with > this? Your not going to get squat in enhanced resale value > by doing this repair yourself. I'm doing this repair because although I will eventually sell the car, I won't be selling it anytime soon...probably keep the car another year, tops. But you are missing the most important point: Resale value is NOT why I'm doing this repair. I'm doing this repair because this is a safety issue. I should not drive the car in its present condition, and I certainly wouldn't want to sell the car to someone else if it weren't safe to drive. |
#4
|
|||
|
|||
ADVICE NEEDED: Removing Inner Tie Rod Ends - TWO QUESTIONS
Thank you Ted... I'll be sure to pass your remarks on to my customers....
Nearly everything we do to the modern automobile has special considerations.... be it removing or installing spark plugs , installing a wheel or brake pads, deciding on the proper lube spec for any subsystem.... Sadly, some DIYers are better prepared (both toolwise and smartswise) than some "professionals" for many of these tasks.... The OP has the common sense to see that "something is up" and you turn into a dick.... OP... simply push the pin (if present) into the cavity inside the tie rod end... Using a large crescent wrench in the manner TRW perscribes is no big deal.. but I highly recommend it to avoid any possible concerns with the rack.On reassembly, I like to use red loctite (I don't care who might have to change these things later... they ain't coming loose on my watch). Torquing these things to spec is always a problem. "Ted Mittelstaedt" > wrote in message ... > > > IMHO the only people who should be buying inner tie rods are > the steering rack rebuild houses. > > Ted > > Thank you Ted... I'll be sure to pass your remarks on to my customers.... Nearly everything we do to the modern automobile has special considerations.... be it removing or installing spark plugs , installing a wheel or brake pads, deciding on the proper lube spec for any subsystem.... Sadly, some DIYers are better prepared (both toolwise and smartswise) than some "professionals" for many of these tasks.... The OP has the common sense to see that "something is up" and you turn into a dick.... OP... simply push the pin (if present) into the cavity inside the tie rod end... Using a large crescent wrench in the manner TRW perscribes is no big deal.. but I highly recommend it to avoid any possible concerns with the rack.On reassembly, I like to use red loctite (I don't care who might have to change these things later... they ain't coming loose on my watch). Torquing these things to spec is always a problem. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Advice needed - UK | Mike Cook | BMW | 14 | June 11th 06 09:37 PM |
Some much needed advice please! (UK) | Harry | BMW | 8 | July 7th 05 03:10 PM |
Advice and Help With Removing Broken Spark Plug | BibBob5 | Ford Explorer | 0 | February 23rd 05 11:31 PM |
Advice needed regarding 540 E39 | RAFA KRAWCZYK | BMW | 2 | December 27th 04 04:54 PM |
Help/Advice Needed | RHinNC | Simulators | 3 | December 25th 04 11:47 PM |