If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
how do I tell which is exhaust and which is the intake valve with theintake manifold on?
I aplogoze in advance because this is probably a dumb question, but I
cannot find the answer to it. I had a heck of a noise going on in my 350 V8 chevy engine. I checked it out and one of the rocker arms was quite loose. I am reading up on how to set the clearance on the lifters. I snag #1 cyl and get it at TDC using the marks on the flywheel. I can tell the cyl # by the stamp on the engine block. Then I can set certain exhaust and intakes to proper clearance. No problem since all the cylinder numbers are marked on the head. 1. BUT how do I tell which is exhaust and which is the intake valve with the intake manifold on? Been looking in the book and I see no info on that. Then I move and set it for #6 cyl and then do the rest of the rocker settings. 2. Been wondering how come that rocker was so loose. As I understand it, the hydraulic lifter is just an oil filled damper chamber to take up erratic slackness within fine limits. If it was stuck it would make a clicking noise, but would not be THAT loose? Or do I misunderstand? |
Ads |
#2
|
|||
|
|||
how do I tell which is exhaust and which is the intake valve withthe intake manifold on?
On Apr 7, 9:24*pm, BSAKing > wrote:
> I aplogoze in advance because this is probably a dumb question, but I > cannot find the answer to it. > > I had a heck of a noise going on in my 350 V8 chevy engine. I checked > it out and one of the rocker arms was quite loose. > > I am reading up on how to set the clearance on the lifters. I snag #1 > cyl and get it at TDC using the marks on the flywheel. I can tell the > cyl # by the stamp on the engine block. Then I can set certain exhaust > and intakes to proper clearance. No problem since all the cylinder > numbers are marked on the head. > > 1. BUT how do I tell which is exhaust and which is the intake valve > with the intake manifold on? Been looking in the book and I see no > info on that. > > Then I move and set it for #6 cyl and then do the rest of the rocker > settings. > > 2. Been wondering how come that rocker was so loose. As I understand > it, the hydraulic lifter is just an oil filled damper chamber to take > up erratic slackness within fine limits. If it was stuck it would make > a clicking noise, but would not be THAT loose? Or do I misunderstand? PS> I checked and the pushrod and the rocker itself seem just fine and oil comes out exactly as it should. |
#3
|
|||
|
|||
how do I tell which is exhaust and which is the intake valve withthe intake manifold on?
On Apr 7, 6:24*pm, BSAKing > wrote:
> I aplogoze in advance because this is probably a dumb question, but I > cannot find the answer to it. > > I had a heck of a noise going on in my 350 V8 chevy engine. I checked > it out and one of the rocker arms was quite loose. > > I am reading up on how to set the clearance on the lifters. I snag #1 > cyl and get it at TDC using the marks on the flywheel. I can tell the > cyl # by the stamp on the engine block. Then I can set certain exhaust > and intakes to proper clearance. No problem since all the cylinder > numbers are marked on the head. > > 1. BUT how do I tell which is exhaust and which is the intake valve > with the intake manifold on? Been looking in the book and I see no > info on that. > > Then I move and set it for #6 cyl and then do the rest of the rocker > settings. > > 2. Been wondering how come that rocker was so loose. As I understand > it, the hydraulic lifter is just an oil filled damper chamber to take > up erratic slackness within fine limits. If it was stuck it would make > a clicking noise, but would not be THAT loose? Or do I misunderstand? Starting on the left No. 1 valve is exhaust, 2&3 are intake 4 & 5 are exhaust, 6 & 7 are intake and 8 is exhaust. It has been a while but I used the "add to 9 method" meaning when #1 is fully open adjust #8, when #2 is open adjust #7, etc. Good luck PDDeen PDDeen |
#4
|
|||
|
|||
how do I tell which is exhaust and which is the intake valvewith the intake manifold on?
On 4/7/2011 20:24, BSAKing wrote: > I aplogoze in advance because this is probably a dumb question, but I > cannot find the answer to it. > > I had a heck of a noise going on in my 350 V8 chevy engine. I checked > it out and one of the rocker arms was quite loose. > > I am reading up on how to set the clearance on the lifters. I snag #1 > cyl and get it at TDC using the marks on the flywheel. I can tell the > cyl # by the stamp on the engine block. Then I can set certain exhaust > and intakes to proper clearance. No problem since all the cylinder > numbers are marked on the head. > > 1. BUT how do I tell which is exhaust and which is the intake valve > with the intake manifold on? Been looking in the book and I see no > info on that. > Look at the runners on the intake manifold. |
#5
|
|||
|
|||
how do I tell which is exhaust and which is the intake valve withthe intake manifold on?
On Apr 9, 2:43*pm, Bob I > wrote:
> On 4/7/2011 20:24, BSAKing wrote: > > > > > I aplogoze in advance because this is probably a dumb question, but I > > cannot find the answer to it. > > > I had a heck of a noise going on in my 350 V8 chevy engine. I checked > > it out and one of the rocker arms was quite loose. > > > I am reading up on how to set the clearance on the lifters. I snag #1 > > cyl and get it at TDC using the marks on the flywheel. I can tell the > > cyl # by the stamp on the engine block. Then I can set certain exhaust > > and intakes to proper clearance. No problem since all the cylinder > > numbers are marked on the head. > > > 1. BUT how do I tell which is exhaust and which is the intake valve > > with the intake manifold on? Been looking in the book and I see no > > info on that. > > Look at the runners on the intake manifold. An update: I had the valve covers off and the #3 from the back on the passenger side on the 350 V8 chevy block was loose as all get out. I could adjust it down a bit and it helped remove some slap, but some noise is still there. I noticed that I do not think the valve and spring assembly seem to travel quite as much as the others when running. The vehicle does not seem to run poorly though. Does this sound symptomatic of a collapsed hydraulic lifter? The car is garaged up here in Canada during the winter, run infrequently over that time period, and the engine is all original, so I am thinking this is (hopefully) the cause and replacing the lifter(s) would fix the problem. I change the oil myself and I have not noticed any filings or debris in it, so I am hoping that this does not mean there is a cam lobe badly worn. Does this sound likely or am I just being hopeful? |
#6
|
|||
|
|||
how do I tell which is exhaust and which is the intake valvewith the intake manifold on?
On 4/14/2011 13:27, BSAKing wrote: > On Apr 9, 2:43 pm, Bob > wrote: >> On 4/7/2011 20:24, BSAKing wrote: >> >> >> >>> I aplogoze in advance because this is probably a dumb question, but I >>> cannot find the answer to it. >> >>> I had a heck of a noise going on in my 350 V8 chevy engine. I checked >>> it out and one of the rocker arms was quite loose. >> >>> I am reading up on how to set the clearance on the lifters. I snag #1 >>> cyl and get it at TDC using the marks on the flywheel. I can tell the >>> cyl # by the stamp on the engine block. Then I can set certain exhaust >>> and intakes to proper clearance. No problem since all the cylinder >>> numbers are marked on the head. >> >>> 1. BUT how do I tell which is exhaust and which is the intake valve >>> with the intake manifold on? Been looking in the book and I see no >>> info on that. >> >> Look at the runners on the intake manifold. > > An update: I had the valve covers off and the #3 from the back on the > passenger side on the 350 V8 chevy block was loose as all get out. I > could adjust it down a bit and it helped remove some slap, but some > noise is still there. I noticed that I do not think the valve and > spring assembly seem to travel quite as much as the others when > running. The vehicle does not seem to run poorly though. > > Does this sound symptomatic of a collapsed hydraulic lifter? > > The car is garaged up here in Canada during the winter, run > infrequently over that time period, and the engine is all original, so > I am thinking this is (hopefully) the cause and replacing the > lifter(s) would fix the problem. I change the oil myself and I have > not noticed any filings or debris in it, so I am hoping that this does > not mean there is a cam lobe badly worn. > > Does this sound likely or am I just being hopeful? I suppose it's possible the stud is pulling out too. |
#7
|
|||
|
|||
how do I tell which is exhaust and which is the intake valve with the intake manifold on?
"Bob I" > wrote in message ... > > > On 4/14/2011 13:27, BSAKing wrote: >> On Apr 9, 2:43 pm, Bob > wrote: >>> On 4/7/2011 20:24, BSAKing wrote: >>> >>> >>> >>>> I aplogoze in advance because this is probably a dumb question, >>>> but I >>>> cannot find the answer to it. >>> >>>> I had a heck of a noise going on in my 350 V8 chevy engine. I >>>> checked >>>> it out and one of the rocker arms was quite loose. >>> >>>> I am reading up on how to set the clearance on the lifters. I >>>> snag #1 >>>> cyl and get it at TDC using the marks on the flywheel. I can tell >>>> the >>>> cyl # by the stamp on the engine block. Then I can set certain >>>> exhaust >>>> and intakes to proper clearance. No problem since all the >>>> cylinder >>>> numbers are marked on the head. >>> >>>> 1. BUT how do I tell which is exhaust and which is the intake >>>> valve >>>> with the intake manifold on? Been looking in the book and I see >>>> no >>>> info on that. >>> >>> Look at the runners on the intake manifold. >> >> An update: I had the valve covers off and the #3 from the back on >> the >> passenger side on the 350 V8 chevy block was loose as all get out. >> I >> could adjust it down a bit and it helped remove some slap, but some >> noise is still there. I noticed that I do not think the valve and >> spring assembly seem to travel quite as much as the others when >> running. The vehicle does not seem to run poorly though. >> >> Does this sound symptomatic of a collapsed hydraulic lifter? >> >> The car is garaged up here in Canada during the winter, run >> infrequently over that time period, and the engine is all original, >> so >> I am thinking this is (hopefully) the cause and replacing the >> lifter(s) would fix the problem. I change the oil myself and I have >> not noticed any filings or debris in it, so I am hoping that this >> does >> not mean there is a cam lobe badly worn. >> >> Does this sound likely or am I just being hopeful? > > I suppose it's possible the stud is pulling out too. About that time Chevrolet had a hot spot in the center of the valve train due to engine temperature increase. It crystallized the oil and ground the cam lobes down. Cure was a new cam and lifters. Had to replace both on my '74 and '78 at about 70K. |
#8
|
|||
|
|||
how do I tell which is exhaust and which is the intake valve withthe intake manifold on?
> Just an update - I finally screwed up the courage to look more closely
> at the beast. I pulled the valve covers and intake manifold and put a > dial indicator on the push rods while hand rotating the engine. It turns > out one exhaust lobe (at least) was worn down to a nubbin. The > dial indicator rotated 2 1/2 turns with other valves and barely once on > this one. Some of the other lifters were worn or scaled, but I did not bother > to check the lobes on them - it has to come out anyways. > I have a mild cam with lifters, springs, en route and am replacing the distributor > assembly in its entirety. An entire assembly is cheaper than replacing parts > and then I do not have the end play in a 35+ year old unit to contend with. > I have the car, intake, distributor, alternator, A/C, off it and am getting the hose > connections off to pull the rad and fan shroud. Then out comes the engine. Should be > fun, never having done this type of thing before.... Live and learn! |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
How to tell intake and exhaust valve with the intake manifold on? | BSAKing | Technology | 44 | March 2nd 17 04:31 PM |
03' CRV: P0661....Intake Manifold Tuning Valve Control Circuit Low(Bank 1) | ndccpf1 | Honda | 1 | December 31st 09 07:30 PM |
Valve,Butterfly valve,Globe valve,Check valve,Ball valve,Plug valve,Marine valve,Gate valve,Flow control valve | [email protected] | Alfa Romeo | 0 | April 17th 06 08:20 AM |
'79 CJ5 intake/exhaust manifold gasket | Ron Croonenberg | Jeep | 12 | April 15th 06 02:34 AM |
5.9 Hi-Po Intake Manifold | RCSnyder | Jeep | 11 | February 3rd 06 12:52 AM |