If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
83 HiLix pickup tow bar?
Hi all,
I'm trying to help my potential son_in_law sort out a tow bar on his new_to_him 1983 2L petrol Toyota HiLux pickup but not sure if this is the right place. If it isn't could someone kindly suggest a more suitable n/g please. Anyway, in case it is ... there is a fairly substantial tubular steel bumper style bar going across the back that happens to have two 16mm diameter and tow ball bolt spaced tubes going through it. The problem is even with the truck fairly well loaded (a bed full of red cedar and other gear) this bar is a good 500mm off the road and I understand the optimum height for the ball mounting holes should be more like 300mm? (to allow a ball to bring it back up to a nominal 380mm 'laden'). I've also compared what is there already against a scaleable diagram of another towbar and it seems the two are pretty close re the key dimensions. However, the drawing was for a Toyota HiLux 4x4 and I think the crucial but missing info may be 'pickup'? So, can anyone confirm a 1983 HiLux 4x4 Pickup would look like it had been 'lifted' from std (large gaps over the wheels to the wheel-arches) or has this one actually been lifted somehow (we can't see where and don't believe it was done by the po who had it from nearly new) please? All the best. T i m |
Ads |
#2
|
|||
|
|||
83 HiLix pickup tow bar?
On Sat, 07 Aug 2010 00:14:46 +0100, T i m > wrote:
>Hi all, > >I'm trying to help my potential son_in_law sort out a tow bar on his >new_to_him 1983 2L petrol Toyota HiLux pickup but not sure if this is >the right place. If it isn't could someone kindly suggest a more >suitable n/g please. > >Anyway, in case it is ... there is a fairly substantial tubular steel >bumper style bar going across the back that happens to have two 16mm >diameter and tow ball bolt spaced tubes going through it. > >The problem is even with the truck fairly well loaded (a bed full of >red cedar and other gear) this bar is a good 500mm off the road and I >understand the optimum height for the ball mounting holes should be >more like 300mm? (to allow a ball to bring it back up to a nominal >380mm 'laden'). > >I've also compared what is there already against a scaleable diagram >of another towbar and it seems the two are pretty close re the key >dimensions. However, the drawing was for a Toyota HiLux 4x4 and I >think the crucial but missing info may be 'pickup'? > >So, can anyone confirm a 1983 HiLux 4x4 Pickup would look like it had >been 'lifted' from std (large gaps over the wheels to the >wheel-arches) or has this one actually been lifted somehow (we can't >see where and don't believe it was done by the po who had it from >nearly new) please? > >All the best. > >T i m You are towing it backwards? I doubt 150 MM will make much difference, but what about a drop/raise hitch assembly? |
#3
|
|||
|
|||
83 HiLix pickup tow bar?
On Sat, 07 Aug 2010 08:53:20 -0400, PeterD > wrote:
>>The problem is even with the truck fairly well loaded (a bed full of >>red cedar and other gear) this bar is a good 500mm off the road and I >>understand the optimum height for the ball mounting holes should be >>more like 300mm? (to allow a ball to bring it back up to a nominal >>380mm 'laden'). >> >>I've also compared what is there already against a scaleable diagram >>of another towbar and it seems the two are pretty close re the key >>dimensions. However, the drawing was for a Toyota HiLux 4x4 and I >>think the crucial but missing info may be 'pickup'? >> >>So, can anyone confirm a 1983 HiLux 4x4 Pickup would look like it had >>been 'lifted' from std (large gaps over the wheels to the >>wheel-arches) or has this one actually been lifted somehow (we can't >>see where and don't believe it was done by the po who had it from >>nearly new) please? >> > >You are towing it backwards? Not towed anything yet, not got a tow ball fitted. ;-) > >I doubt 150 MM will make much difference, but what about a drop/raise >hitch assembly? Yes, that would do but I would still have to fabricate a support for the lower end? I was looking at a few Hi-Li today, although they were mostly later models and they used a different design of bar (they tended to hook 'over' the top of the rear chassis rails and had a much longer drop). Looking at the existing design on our I might be able to drop the bar a bit where it joins the support bracket / plates and again with a drop plate. However I may also look to see how I could brace from the bottom of the assembly back up to the chassis somewhere (without impacting on access to the spare wheel etc). Cheers, T i m |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Tow Bar Q. | Devo | VW air cooled | 6 | March 13th 09 04:32 PM |
Jeep XJ Tow Bar | Grumman-581 | Jeep | 7 | May 16th 07 09:16 PM |
FS: Tow Bar | DBLZOOM | VW air cooled | 1 | May 11th 06 03:19 PM |
E34 Tow Bar | [email protected] | BMW | 0 | March 20th 06 07:21 PM |
tow bar electrics | derek | Jeep | 5 | March 8th 06 10:43 PM |