If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
About the 7.5" axle
I'm getting tired of looking for a reasonable 8.8" axle and finding
$1000 deals on what appear to be unknown crap. For $1400 I can get a brand spankin new one. I'm reading that the 7.5 is good up to 400 hp. Well, that does seem like a lot of horse power, something my v6 will never put out. I'm looking for 3.73 gears and I'm willing to put in an 8.8" axle. I'm always being told that I'm likely to break my 7.5" if I put in 3.73 gears. So after that blurb, assuming I put in 3.73 gears, my question is, what breaks on the 7.5" axle? The gears? The axle shafts? The pumpkin? What is the weak link? I've found nothing on the web on this. All I see is a lot of "I've see a ton of 7.5's broken..." and such. Lot's of talk, no examples. I have a 2009 v6 vert, auto trans, GT exhaust take-offs, cold air intake, and an SCT tune. That's probably the end of power train mods for me. If I wish real hard I might be getting 240 hp. Will I break mine if I stomp on it now and then with 3.73's? Thanks for reading. -- For all you know this message was... Sent via an exclusive network, on a snobby portable computing device. |
Ads |
#2
|
|||
|
|||
About the 7.5" axle
On Mon, 24 Jun 2013 13:21:27 -0400, twk >
wrote: >I'm getting tired of looking for a reasonable 8.8" axle and finding >$1000 deals on what appear to be unknown crap. For $1400 I can get a >brand spankin new one. > >I'm reading that the 7.5 is good up to 400 hp. Well, that does seem like >a lot of horse power, something my v6 will never put out. > >I'm looking for 3.73 gears and I'm willing to put in an 8.8" axle. I'm >always being told that I'm likely to break my 7.5" if I put in 3.73 >gears. > >So after that blurb, assuming I put in 3.73 gears, my question is, what >breaks on the 7.5" axle? The gears? The axle shafts? The pumpkin? What >is the weak link? > >I've found nothing on the web on this. All I see is a lot of "I've see a >ton of 7.5's broken..." and such. Lot's of talk, no examples. > >I have a 2009 v6 vert, auto trans, GT exhaust take-offs, cold air >intake, and an SCT tune. That's probably the end of power train mods for >me. If I wish real hard I might be getting 240 hp. Will I break mine if >I stomp on it now and then with 3.73's? > >Thanks for reading. This is just my gut talking...... If you had a manual transmission and were launching by dumping the clutch at 4000 rpm it would be a worry, but with the Automatic you aren't going to get that kind of shock load so I don't think you will see a problem. So assuming it's been ok now, the only thing I can see the 3.73 possibly causing to break would be the axle shafts, those are the parts that will be mostly getting any additional load from the ratio change. But my gut says nothing will break since you are running an auto. And if you didn't abuse it, probably nothing would break with a manual. |
#3
|
|||
|
|||
About the 7.5" axle
My experience with 7.5" Ford differentials is like yours: I had one,
wished it was 8.8", and had no difficulties with it, but was apprehensive about its durability, which seemed to be questionable based on I-net readings. My belief is that a properly-installed set of 3.73 gears will not influence the expected life of a 7.5 differential under the conditions you mention, which are very similar to those I applied during a kind-of-abusive three-year "sporting-use" of my V6 auto-equipped car. -- Frank ess "twk" > wrote in message ... > I'm getting tired of looking for a reasonable 8.8" axle and finding > $1000 deals on what appear to be unknown crap. For $1400 I can get a > brand spankin new one. > > I'm reading that the 7.5 is good up to 400 hp. Well, that does seem > like > a lot of horse power, something my v6 will never put out. > > I'm looking for 3.73 gears and I'm willing to put in an 8.8" axle. I'm > always being told that I'm likely to break my 7.5" if I put in 3.73 > gears. > > So after that blurb, assuming I put in 3.73 gears, my question is, > what > breaks on the 7.5" axle? The gears? The axle shafts? The pumpkin? What > is the weak link? > > I've found nothing on the web on this. All I see is a lot of "I've see > a > ton of 7.5's broken..." and such. Lot's of talk, no examples. > > I have a 2009 v6 vert, auto trans, GT exhaust take-offs, cold air > intake, and an SCT tune. That's probably the end of power train mods > for > me. If I wish real hard I might be getting 240 hp. Will I break mine > if > I stomp on it now and then with 3.73's? > > Thanks for reading. > > -- > For all you know this message was... > Sent via an exclusive network, on a snobby portable computing device. |
#4
|
|||
|
|||
About the 7.5" axle
In article >,
Ashton Crusher > wrote: > On Mon, 24 Jun 2013 13:21:27 -0400, twk > > wrote: > > >I'm getting tired of looking for a reasonable 8.8" axle and finding > >$1000 deals on what appear to be unknown crap. For $1400 I can get a > >brand spankin new one. > > > >I'm reading that the 7.5 is good up to 400 hp. Well, that does seem like > >a lot of horse power, something my v6 will never put out. > > > >I'm looking for 3.73 gears and I'm willing to put in an 8.8" axle. I'm > >always being told that I'm likely to break my 7.5" if I put in 3.73 > >gears. > > > >So after that blurb, assuming I put in 3.73 gears, my question is, what > >breaks on the 7.5" axle? The gears? The axle shafts? The pumpkin? What > >is the weak link? > > > >I've found nothing on the web on this. All I see is a lot of "I've see a > >ton of 7.5's broken..." and such. Lot's of talk, no examples. > > > >I have a 2009 v6 vert, auto trans, GT exhaust take-offs, cold air > >intake, and an SCT tune. That's probably the end of power train mods for > >me. If I wish real hard I might be getting 240 hp. Will I break mine if > >I stomp on it now and then with 3.73's? > > > >Thanks for reading. > > > This is just my gut talking...... If you had a manual transmission > and were launching by dumping the clutch at 4000 rpm it would be a > worry, but with the Automatic you aren't going to get that kind of > shock load so I don't think you will see a problem. So assuming it's > been ok now, the only thing I can see the 3.73 possibly causing to > break would be the axle shafts, those are the parts that will be > mostly getting any additional load from the ratio change. But my gut > says nothing will break since you are running an auto. And if you > didn't abuse it, probably nothing would break with a manual. Wow, thanks Frank & Ashton. There are others that would agree with you. I do have a very reputable mustang specialty shop within walking distance. They've done many gears. They rebuilt me an 8.8" axle & GT exhaust take-offs for my old '94 v6 mustang. I have one last 8.8 to check out, hopefully tomorrow, then I might just have to put gears and a traction lock in my 7.5". Thanks for your opinions. twk -- For all you know this message was... Sent via an exclusive network, on a snobby portable computing device. |
#5
|
|||
|
|||
About the 7.5" axle
"twk" > wrote in message ... > I'm getting tired of looking for a reasonable 8.8" axle and finding > $1000 deals on what appear to be unknown crap. For $1400 I can get a > brand spankin new one. > > I'm reading that the 7.5 is good up to 400 hp. Well, that does seem like > a lot of horse power, something my v6 will never put out. > > I'm looking for 3.73 gears and I'm willing to put in an 8.8" axle. I'm > always being told that I'm likely to break my 7.5" if I put in 3.73 > gears. > > So after that blurb, assuming I put in 3.73 gears, my question is, what > breaks on the 7.5" axle? The gears? The axle shafts? The pumpkin? What > is the weak link? > > I've found nothing on the web on this. All I see is a lot of "I've see a > ton of 7.5's broken..." and such. Lot's of talk, no examples. > > I have a 2009 v6 vert, auto trans, GT exhaust take-offs, cold air > intake, and an SCT tune. That's probably the end of power train mods for > me. If I wish real hard I might be getting 240 hp. Will I break mine if > I stomp on it now and then with 3.73's? > > Thanks for reading. > tires will peel out first. save your money for tickets. save your money if it really breaks. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Repost__012613__DVD 03 Fords - "1948 Ford flathead powered midget racer- rear axle end s =Pat D.jpg" 172.2 KBytes | [email protected] | Auto Photos | 0 | January 26th 13 09:53 PM |
"Columbia Axle Company_1935_07_00.jpg" 388.7 KBytes | [email protected] | Auto Photos | 0 | November 24th 12 07:56 PM |
2013 8.8" axle for an '09 v6 | twk | Ford Mustang | 0 | September 25th 12 07:10 PM |
Repost__092212 - "1939 Mercedes-Benz G4 540 Dual-Axle Touring Car Tan & Black Rt Frt Qtr =ATM.jpg" 190.7 KBytes | [email protected] | Auto Photos | 0 | September 22nd 12 05:58 PM |
Repost__092212 - "1939 Mercedes Benz G4 Offroader Rear Axle =24Bit.jpg" 110.3 KBytes | [email protected] | Auto Photos | 0 | September 22nd 12 05:57 PM |