If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Crankshaft Position Sensor replacement
2000 Silverado 5.3L, 4X4, 167K
I need to replace the Crankshaft Position Sensor. The manual states that after replacement it must be connected to a scan tool for a "CKP System Variation Learn Procedure". Is this something that needs to be done at a dealership or can it be done with a generic scan tool? Is there a way to do it without a scan tool? Thanks for any advice, Al Bottoms Up Divers |
Ads |
#2
|
|||
|
|||
Crankshaft Position Sensor replacement
In article
>, "ajtessier" > wrote: > 2000 Silverado 5.3L, 4X4, 167K > > I need to replace the Crankshaft Position Sensor. The manual states that > after replacement it must be connected to a scan tool for a "CKP System > Variation Learn Procedure". Is this something that needs to be done at a > dealership or can it be done with a generic scan tool? Is there a way to do > it without a scan tool? > > Thanks for any advice, > Al > Bottoms Up Divers It doesn't have to be done at a dealership, most high end scan tools can perform the crank variation relearn. Auto Enginuity, Snap-On, OTC, Ease, etc. |
#3
|
|||
|
|||
Crankshaft Position Sensor replacement
Thanks for your quick response, I have a friend with a high quality scan
tool (don't know the brand) but he's away for a few days so I couldn't ask him. If I install the sensor at home would I be able to drive to his shop (about 6 miles) or do I need to do the learn procedure before I drive it.? Al Bottoms Up Divers "aarcuda69062" > wrote in message ... > In article > >, > "ajtessier" > wrote: > >> 2000 Silverado 5.3L, 4X4, 167K >> >> I need to replace the Crankshaft Position Sensor. The manual states that >> after replacement it must be connected to a scan tool for a "CKP System >> Variation Learn Procedure". Is this something that needs to be done at a >> dealership or can it be done with a generic scan tool? Is there a way to >> do >> it without a scan tool? >> >> Thanks for any advice, >> Al >> Bottoms Up Divers > > It doesn't have to be done at a dealership, most high end scan > tools can perform the crank variation relearn. > > Auto Enginuity, Snap-On, OTC, Ease, etc. |
#4
|
|||
|
|||
Crankshaft Position Sensor replacement
You can drive the truck without doing the learn procedure. ajtessier wrote: > > Thanks for your quick response, I have a friend with a high quality scan > tool (don't know the brand) but he's away for a few days so I couldn't ask > him. > > If I install the sensor at home would I be able to drive to his shop (about > 6 miles) or do I need to do the learn procedure before I drive it.? -- Mike Walsh |
#5
|
|||
|
|||
Crankshaft Position Sensor replacement - it's in but
I got the new sensor in today but we weren't able to do the learn procedure.
It seems to run fine (only drove it about six miles home). Is it possible that I won't have to do it? I am going to the dealer Monday for an unrelated recall, should I ask them to do it even if it's still running fine? Al Bottoms Up Divers "Mike Walsh" > wrote in message ... > > You can drive the truck without doing the learn procedure. > > ajtessier wrote: >> >> Thanks for your quick response, I have a friend with a high quality scan >> tool (don't know the brand) but he's away for a few days so I couldn't >> ask >> him. >> >> If I install the sensor at home would I be able to drive to his shop >> (about >> 6 miles) or do I need to do the learn procedure before I drive it.? > > -- > Mike Walsh |
#6
|
|||
|
|||
Crankshaft Position Sensor replacement - it's in but
ajtessier > wrote:
>I got the new sensor in today but we weren't able to do the learn procedure. >It seems to run fine (only drove it about six miles home). Is it possible >that I won't have to do it? I am going to the dealer Monday for an unrelated >recall, should I ask them to do it even if it's still running fine? It is running fine, but it will run BETTER if you do the procedure. It will only take five minutes and save you hundreds of dollars in gasoline over the long run.... --scott -- "C'est un Nagra. C'est suisse, et tres, tres precis." |
#7
|
|||
|
|||
Crankshaft Position Sensor replacement - it's in but
When I worked for used car lots I used to 'teach' GM's how to idle right
on a regular basis after extended periods of no power connected up. The procedure was to drive for 5 miles staying 'under' 30 mph, then shut it down. Start up again and drive another 5 miles keeping under 30, then shut it down again. One more repeat of this and then bring it up to speed. After that they all just purred at idle. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 'New' frame in the works for '08 ajtessier wrote: > I got the new sensor in today but we weren't able to do the learn procedure. > It seems to run fine (only drove it about six miles home). Is it possible > that I won't have to do it? I am going to the dealer Monday for an unrelated > recall, should I ask them to do it even if it's still running fine? > > Al > Bottoms Up Divers > > > "Mike Walsh" > wrote in message > ... >> You can drive the truck without doing the learn procedure. >> >> ajtessier wrote: >>> Thanks for your quick response, I have a friend with a high quality scan >>> tool (don't know the brand) but he's away for a few days so I couldn't >>> ask >>> him. >>> >>> If I install the sensor at home would I be able to drive to his shop >>> (about >>> 6 miles) or do I need to do the learn procedure before I drive it.? >> -- >> Mike Walsh > > |
#8
|
|||
|
|||
Crankshaft Position Sensor replacement - it's in but
That is how my Beretta was. The older it got the more the sensors went out of range and it took several cold to warm cycles to get it back in calibration after disconnecting the battery. Many sensors e.g. throttle position and temperature that must output a signal that varies according to a varying input will gradually change there performance over time, but a crankshaft position sensor should not have this problem because all it does is put out a pulse when a metal piece goes by the sensor. Mike Romain wrote: > > When I worked for used car lots I used to 'teach' GM's how to idle right > on a regular basis after extended periods of no power connected up. > > The procedure was to drive for 5 miles staying 'under' 30 mph, then shut > it down. Start up again and drive another 5 miles keeping under 30, > then shut it down again. One more repeat of this and then bring it up > to speed. > > After that they all just purred at idle. > -- Mike Walsh |
#9
|
|||
|
|||
Crankshaft Position Sensor replacement - it's in but
In article
om>, Mike Romain > wrote: > When I worked for used car lots I used to 'teach' GM's how to idle right > on a regular basis after extended periods of no power connected up. > > The procedure was to drive for 5 miles staying 'under' 30 mph, then shut > it down. Start up again and drive another 5 miles keeping under 30, > then shut it down again. One more repeat of this and then bring it up > to speed. > > After that they all just purred at idle. > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 'New' frame in the works for '08 What does this have to do with the OPs vehicle? |
#10
|
|||
|
|||
Crankshaft Position Sensor replacement
a good quility scan tool can do the relearn if the software is in it
but a few drive cycles and you might get lucky ajtessier wrote: > 2000 Silverado 5.3L, 4X4, 167K > > I need to replace the Crankshaft Position Sensor. The manual states that > after replacement it must be connected to a scan tool for a "CKP System > Variation Learn Procedure". Is this something that needs to be done at a > dealership or can it be done with a generic scan tool? Is there a way to do > it without a scan tool? > > Thanks for any advice, > Al > Bottoms Up Divers |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Crankshaft position sensor on 89 Wrangler | sozai | Jeep | 2 | September 8th 06 01:26 AM |
crankshaft position sensor help | randy pape | Dodge | 6 | February 9th 06 01:22 AM |
Is it possible to bypass the CPS (Crankshaft Position Sensor, Crankcase Position Sensor) | Erich | Jeep | 16 | January 30th 06 12:12 PM |
AWA [OFFER] MOTORCRAFT #DY912 CRANKSHAFT POSITION SENSOR | [email protected] | General | 0 | January 4th 06 05:01 PM |
Locate the crankshaft position sensor | Leo | Saturn | 2 | January 18th 05 03:31 PM |