A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » VW water cooled
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

94 Jetta III - Transmission Fluid/Oil Level



 
 
Thread Tools Display Modes
  #1  
Old June 12th 06, 04:41 AM posted to rec.autos.makers.vw.watercooled
external usenet poster
 
Posts: n/a
Default 94 Jetta III - Transmission Fluid/Oil Level

Hi, Just a quick question.

I have a 94 Jetta III (2.0L) w/ manual trans, and I was wondering if
there's a way to check the transmission oil. I can't find a stick or a
hole or anything that might indicate if I need more oil, if it's bad,
anything. Is there a way to check it? Also, should I need more/need a
flush, do I need to make a run to the dealer to get that done or could
"Bob's Transmission-o-Rama" (or where ever) probably do that for me?

TIA,
Kyle

Ads
  #2  
Old June 12th 06, 07:07 AM posted to rec.autos.makers.vw.watercooled
external usenet poster
 
Posts: n/a
Default 94 Jetta III - Transmission Fluid/Oil Level

Hey Kyle what are you in need of checking the trany oil for? Have you
noticed any problems like a leak or 5th gear popping out?

Well to answer your question, its pretty simple once you know how and
get the hang of it. Basically theres a Plug on the side of the
transmissions. It'll be on the drivers side right next to the wheel.
You'll need a 17mm Allen wrench, or homemade tool using the right size
bolt head and a couple nuts, to take it off. To get to it I'd suggest
turning the wheels all the way to the left, then there'll be a plastic
shield next to the wheel you'll have to rip out and that'll expose the
side of the trany. Basically as long as the fluid is level with that
hole then you should be good to go.

You might wanna mention your mileage. I'm not sure offhand when one
should normally replace the oil. IIRC Bentley & VW say it should last
the lifetime of the vehicle or never need replacement. But I think at
around 100k I switched over to Redline MT-90 just to be on the safe
side.

  #3  
Old June 14th 06, 09:56 PM posted to rec.autos.makers.vw.watercooled
external usenet poster
 
Posts: n/a
Default 94 Jetta III - Transmission Fluid/Oil Level

wrote:
> Hi, Just a quick question.


> I have a 94 Jetta III (2.0L) w/ manual trans, and I was wondering if
> there's a way to check the transmission oil. I can't find a stick or a
> hole or anything that might indicate if I need more oil, if it's bad,
> anything. Is there a way to check it? Also, should I need more/need a
> flush, do I need to make a run to the dealer to get that done or could
> "Bob's Transmission-o-Rama" (or where ever) probably do that for me?


I don't know when they switched over to the new way of doing things
(probably before your car), but I still don't see the point. Fill through
the speedometer cable hole and drain through the plug at the bottom. The
drain plug requires a 17mm hex wrench (Sears sells it, or you can ghetto
rig a lug bolt). The speedo cable can be removed with an 11mm socket on a
long extension. Remove the bolt holding in the bracket and then jiggle it
loose.

The car takes 2 liters (2.1 quarts -- but most people just use 2 quarts in
the US) of GL-4 transmission fluid (*NOT* GL-5 or anything that says GL-5
compliant regardless of whether or not its GL-4 compliant). Most people
recommend Redline MTL or MT-90 (for cooler and warmer climates
respectively). Bentley claims the fluid is good for the life of the car,
but its probably not a bad idea to replace it every 10 years or so.
Besides, Redline is a lot better than the stuff VW was using in 94. Plus
its bright red, so if its leaking, its pretty obvious what it is.

I personally wouldn't take it to Bob's Transmission-O-Rama... Why bother?
It's no harder than any other oil change, you just need basic hand tools,
a funnel, and a 17mm hex wrench.
  #4  
Old June 15th 06, 11:57 AM posted to rec.autos.makers.vw.watercooled
external usenet poster
 
Posts: n/a
Default 94 Jetta III - Transmission Fluid/Oil Level

I bought the 17mm hex at Sears and for the life of me I can't get the port
to budge. My car has 150K and I think it should be checked and changed.
Tried some PB blaster last night as well. Would you recommend finding a
socket 17mm Allen and a breaker bar? With the Sears allen I don't seem to
have enough leverage with the car on the ground - tomorrow will put it on
ramps and try again. I guess I could get a steel pipe and slip it on the
end but the hex key is a little wobbly in the port (both drain and fill
check) so I don't want to strip it. Any suggestions? On my VR6 I think my
speedo is at the back of the trans near the manifold downpipe - the Bentley
doesn't show it - is this correct?


"blah" > wrote in message
...
> wrote:
>> Hi, Just a quick question.

>
>> I have a 94 Jetta III (2.0L) w/ manual trans, and I was wondering if
>> there's a way to check the transmission oil. I can't find a stick or a
>> hole or anything that might indicate if I need more oil, if it's bad,
>> anything. Is there a way to check it? Also, should I need more/need a
>> flush, do I need to make a run to the dealer to get that done or could
>> "Bob's Transmission-o-Rama" (or where ever) probably do that for me?

>
> I don't know when they switched over to the new way of doing things
> (probably before your car), but I still don't see the point. Fill through
> the speedometer cable hole and drain through the plug at the bottom. The
> drain plug requires a 17mm hex wrench (Sears sells it, or you can ghetto
> rig a lug bolt). The speedo cable can be removed with an 11mm socket on a
> long extension. Remove the bolt holding in the bracket and then jiggle it
> loose.
>
> The car takes 2 liters (2.1 quarts -- but most people just use 2 quarts in
> the US) of GL-4 transmission fluid (*NOT* GL-5 or anything that says GL-5
> compliant regardless of whether or not its GL-4 compliant). Most people
> recommend Redline MTL or MT-90 (for cooler and warmer climates
> respectively). Bentley claims the fluid is good for the life of the car,
> but its probably not a bad idea to replace it every 10 years or so.
> Besides, Redline is a lot better than the stuff VW was using in 94. Plus
> its bright red, so if its leaking, its pretty obvious what it is.
>
> I personally wouldn't take it to Bob's Transmission-O-Rama... Why bother?
> It's no harder than any other oil change, you just need basic hand tools,
> a funnel, and a 17mm hex wrench.



  #5  
Old June 18th 06, 03:40 AM posted to rec.autos.makers.vw.watercooled
external usenet poster
 
Posts: n/a
Default 94 Jetta III - Transmission Fluid/Oil Level

> Tried some PB blaster last night as well. Would you recommend finding a
> socket 17mm Allen and a breaker bar? With the Sears allen I don't seem to


Yes, that's what I use. Funny enough, I filled my trans with Redline
MTL and then two years later decided to check the level -- I had to use
the breaker bar again and I about gave myself a hernia doing it! I know
I didn't put it in *that* tight.

> check) so I don't want to strip it. Any suggestions? On my VR6 I think my
> speedo is at the back of the trans near the manifold downpipe - the Bentley
> doesn't show it - is this correct?


I guess the speedo hole works, I just used the level-check-hole and
some tubing to fill though. One thing I suggest is filling, driving
around the block to work any bubbles out, then checking and topping off
as needed.

I really like the Redline. Seems to shift easier on those cold winter
days. It helped my 2nd gear "crunch" in my Fox too, a little bit. Still
crunches sometimes but not as bad.

  #6  
Old June 22nd 06, 09:26 PM posted to rec.autos.makers.vw.watercooled
external usenet poster
 
Posts: n/a
Default 94 Jetta III - Transmission Fluid/Oil Level

stim141 > wrote:
> I bought the 17mm hex at Sears and for the life of me I can't get the port
> to budge. My car has 150K and I think it should be checked and changed.
> Tried some PB blaster last night as well. Would you recommend finding a
> socket 17mm Allen and a breaker bar? With the Sears allen I don't seem to
> have enough leverage with the car on the ground - tomorrow will put it on
> ramps and try again. I guess I could get a steel pipe and slip it on the
> end but the hex key is a little wobbly in the port (both drain and fill
> check) so I don't want to strip it. Any suggestions? On my VR6 I think my


I have a steel pipe, about 2-3 feet long that fits perfectly over the 17mm
hex key and most 3/8" and 1/2" ratchets. I love it. With 150k miles on
the car, if its never been budged, its not unreasonable to assume you'd
need extra leverage.

I've always gotten the thing off with the hex key. With stuff that big,
its hard to strip it -- but, its always possible. Use your best
judgement. A 17mm bit socket is available as a specialty tool, but it'll
be expensive. If you can get a welder, an easy alternative maybe to
simply weld a nut onto a lug bolt. Remember, as long as you can get it
out, you can replace it with a new one. If you can't, and you strip it,
you've got a problem.

> speedo is at the back of the trans near the manifold downpipe - the Bentley
> doesn't show it - is this correct?


On the A2's its on the driver's side of the car near the reverse light
switch. It's pretty obvious because there's a greyish-green speedometer
cable (maybe 8mm in diameter) running down to it. If the car doesn't have
a speedo cable it might be less obvious. Don't even think about trying to
remove either of the 17mm set screws until you have the speedo hole open
-- and I wouldn't even mess with the "fill hole" anyway. Also, it should
go without saying, but don't dump fluid onto your clutch/flywheel through
the sight plug.

  #7  
Old June 24th 06, 08:12 PM posted to rec.autos.makers.vw.watercooled
external usenet poster
 
Posts: n/a
Default 94 Jetta III - Transmission Fluid/Oil Level

> If you can get a welder, an easy alternative maybe to
> simply weld a nut onto a lug bolt.


You don't even need a welder for that. Some flux, a brazing rod, and a
propane torch is all you need to attach the nut to the bolt.

And you don't even need that. Put two nuts on your lug bolt and tighten
them to each other. Now stick your bolt in your trans plug and turn on
the inner nut.

  #8  
Old June 25th 06, 09:29 PM posted to rec.autos.makers.vw.watercooled
external usenet poster
 
Posts: n/a
Default 94 Jetta III - Transmission Fluid/Oil Level

My suggestion is to get an Allen socket and a 1/2 " breaker bar to get it
off and put it on with a 3/8" ratchet . I,m pretty sure a piece of pipe or a
jack handle will remove it too if you hold it in with some pressure.
> wrote in message
ups.com...
>> If you can get a welder, an easy alternative maybe to
>> simply weld a nut onto a lug bolt.

>
> You don't even need a welder for that. Some flux, a brazing rod, and a
> propane torch is all you need to attach the nut to the bolt.
>
> And you don't even need that. Put two nuts on your lug bolt and tighten
> them to each other. Now stick your bolt in your trans plug and turn on
> the inner nut.
>



  #9  
Old July 8th 16, 11:18 PM posted to rec.autos.makers.vw.watercooled
Timothy Todd Hagan
external usenet poster
 
Posts: 2
Default 94 Jetta III - Transmission Fluid/Oil Level

replying to blah, Timothy Todd Hagan wrote:
Okay u say fill thru spedo cable and the guy b4 says behind drivers front
wheel? Which is it for a 94 Jetta do u know? Also, if it is how u say can I
see the level b4 I buy and add?

--
posted from
http://www.motorsforum.com/vw/94-jet...vel-33385-.htm


  #10  
Old July 8th 16, 11:18 PM posted to rec.autos.makers.vw.watercooled
Timothy Todd Hagan
external usenet poster
 
Posts: 2
Default 94 Jetta III - Transmission Fluid/Oil Level

replying to tylernt, Timothy Todd Hagan wrote:
Any ideas on the major "crunch" as u put it on my 94 Jetta only when in
reverse. Could it just be low fluid...

--
posted from
http://www.motorsforum.com/vw/94-jet...vel-33385-.htm


 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Help - Diagnostic Bus not working! Duane Chrysler 7 January 15th 06 04:21 PM
Transmission problems ozymandias Technology 2 January 10th 06 02:28 AM
Transmission probelms ozymandias Technology 0 January 9th 06 12:28 AM
Anti-freeze level & trouble light 2001 Jetta RockStarMoney VW water cooled 1 November 26th 05 01:33 AM
New *FREE* Corvette Discussion Forum JLA ENTERPRISES TECHNOLOGIES INTEGRATION Corvette 12 November 30th 04 07:36 PM


All times are GMT +1. The time now is 06:20 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.