A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » Ford Explorer
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Check Engine Light and Fuel Mixture



 
 
Thread Tools Display Modes
  #1  
Old November 11th 04, 12:42 AM
Mark Barrett
external usenet poster
 
Posts: n/a
Default Check Engine Light and Fuel Mixture

I have a high mileage 95 Explorer which I now only use for
biking and camping trips. These trips usually take me through
the mountains of Colorado. Lately and consistently the check
engine light has been going on and off as I drive through the
mountains making significant elevation changes. However, once
I'm at my destination or at home the light stays solid off and
the engine runs smoothly. During the times the light is turning
on and off the engine runs slightly rough. From what I understand
the computer is making adjustments to the fuel mixture during
elevation changes based on the sensor imput from the MAF in the
upper intake manifold and the Hot O2 in the exhaust pipes. I think
there are three Hot O2 sensors in the exhaust system. All of these
sensors are the original. I'm thinking one or more of these
sensors is now marginal.
My question to the group is can I eliminate the on/off of
the check engine light during elevation changes by changing one
or more of these sensors? When the vehicle was newer the check
engine light never came on. However, I can now reliably predict
when the check engine light will start coming on based on where
I am driving in the mountains. I know there are voltage measurements
that can be made to the sensor outputs. However, when I am at home
the light never comes on so I am assuming the sensor outputs are
all in a normal range.

Thanks in advance for any input on this subject.
Mark
Ads
  #2  
Old November 11th 04, 02:53 AM
Mike Iglesias
external usenet poster
 
Posts: n/a
Default

In article >,
Mark Barrett > wrote:
> My question to the group is can I eliminate the on/off of
>the check engine light during elevation changes by changing one
>or more of these sensors? When the vehicle was newer the check
>engine light never came on. However, I can now reliably predict
>when the check engine light will start coming on based on where
>I am driving in the mountains. I know there are voltage measurements
>that can be made to the sensor outputs. However, when I am at home
>the light never comes on so I am assuming the sensor outputs are
>all in a normal range.


The best way to deal with this is to get the codes pulled from the
computer to see why it's turning on the check engine light. I think
places like Kragen or AutoZone will do this for you. Once you know
what is causing the check engine light to come on, check back here
and someone can probably tell you what you need to look at next.


--
Mike Iglesias Email:
University of California, Irvine phone: 949-824-6926
Network & Academic Computing Services FAX: 949-824-2069
  #3  
Old November 11th 04, 08:11 PM
Mike
external usenet poster
 
Posts: n/a
Default

You might have trouble finding a place that will read the codes for a 1995.
I think it wasn't until 1997 models that the interface to read the codes
conformed to the industry standard.
At any rate, I took my 1995 to an autoparts store and they told me they
couldn't read codes off of pre 1997 Explorers.

"Mike Iglesias" > wrote in message
...
> In article >,
> Mark Barrett > wrote:
> > My question to the group is can I eliminate the on/off of
> >the check engine light during elevation changes by changing one
> >or more of these sensors? When the vehicle was newer the check
> >engine light never came on. However, I can now reliably predict
> >when the check engine light will start coming on based on where
> >I am driving in the mountains. I know there are voltage measurements
> >that can be made to the sensor outputs. However, when I am at home
> >the light never comes on so I am assuming the sensor outputs are
> >all in a normal range.

>
> The best way to deal with this is to get the codes pulled from the
> computer to see why it's turning on the check engine light. I think
> places like Kragen or AutoZone will do this for you. Once you know
> what is causing the check engine light to come on, check back here
> and someone can probably tell you what you need to look at next.
>
>
> --
> Mike Iglesias Email:


> University of California, Irvine phone: 949-824-6926
> Network & Academic Computing Services FAX: 949-824-2069



 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
LHS Won’t start in Cold weather and Check engine light on. jgcurt Chrysler 22 January 10th 05 08:57 PM
rec.autos.makers.chrysler FAQ, Part 1/6 Dr. David Zatz Chrysler 10 December 18th 04 06:15 AM
In-the-tank fuel pumps cause death and destruction Silver Surfer Chrysler 293 November 7th 04 04:41 PM
My Beetle's Maintenance Schedule - Help Please! Sleepy Joe VW air cooled 0 October 18th 04 01:53 AM


All times are GMT +1. The time now is 10:36 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.