If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
2000 E46 OBD code 1498
Hi - the check engine light came on today (2000 328i) . I read code 1397 (
Camshaft pos. sensor) along with code 1498. Does anyone know what 1498 is? I saw some info on the web pointing to a transmission fault but that was for a Mini. It said 1498 was for Mini's only - not BMW's. The car runs and drives fine and has 55k miles. How long can I drive with one of the camshaft sensors out? I heard the usual failure mode is oil ingestion due to cracks on the tip?? Thanks for any info. Jeff |
Ads |
#2
|
|||
|
|||
2000 E46 OBD code 1498
i checked the code and it reads " auxiliary
emission controls " . i'm sure that this could mean anything . hth , dick "JeffC" > wrote in message ... > Hi - the check engine light came on today (2000 328i) . I read code 1397 > ( Camshaft pos. sensor) along with code 1498. Does anyone know what 1498 > is? I saw some info on the web pointing to a transmission fault but that > was for a Mini. It said 1498 was for Mini's only - not BMW's. The car runs > and drives fine and has 55k miles. > > How long can I drive with one of the camshaft sensors out? I heard the > usual failure mode is oil ingestion due to cracks on the tip?? > > Thanks for any info. > > Jeff > |
#3
|
|||
|
|||
2000 E46 OBD code 1498
The Cam Sensor does a similar job as the points used to do way back when
they still used points. The engine will not run with a failed cam sensor. I'm a bit confused by the coeds you report. They are not OBD II codes. OBD II codes should be P0nnn, where nnn is in the range of 100 to 999. Codes that are P1nnn are manufacturer specific codes -- they will be for things that one maker might check for, but the others to not check. The Cam Sensor is not a BMW specific code Here is a list of valid OBD II codes, http://autorepair.about.com/od/obdco..._1996_year.htm You should be pulling the OBD II codes from the data port that is mounted along the bottom of the dash board, possibly behind a cover that states OBD Data, or similar. You can pull data from the BMW diagnostic port, but that data might not give the same code information as the OBD II data, and this can lead to confusion. According to the link I posted, P1397 is a Cam Sensor, just as you said (I'm a bit perplexed by this, but let's move on).The "1498" code says it is a Honda/Acura code. "JeffC" > wrote in message ... > Hi - the check engine light came on today (2000 328i) . I read code 1397 > ( Camshaft pos. sensor) along with code 1498. Does anyone know what 1498 > is? I saw some info on the web pointing to a transmission fault but that > was for a Mini. It said 1498 was for Mini's only - not BMW's. The car runs > and drives fine and has 55k miles. > > How long can I drive with one of the camshaft sensors out? I heard the > usual failure mode is oil ingestion due to cracks on the tip?? > > Thanks for any info. > > Jeff > |
#4
|
|||
|
|||
2000 E46 OBD code 1498
In article >,
Jeff Strickland > wrote: > The Cam Sensor does a similar job as the points used to do way back when > they still used points. Not so - it's the crank sensor which basically times the spark. More accurate than a sensor driven via chains etc which stretch. The cam sensor - ignition wise - tells which stroke the engine is on as the crank turns twice per cylinder cycle. > The engine will not run with a failed cam sensor. Think it will after a fashion in the same way as it will with a failed crank sensor. A limp home mode. -- *OK, who stopped payment on my reality check? Dave Plowman London SW To e-mail, change noise into sound. |
#5
|
|||
|
|||
2000 E46 OBD code 1498
this is what i found : " P1498 _ manufacturer contrl auxiliary
emissions controls " . HTH , D. "JeffC" > wrote in message ... > Hi - the check engine light came on today (2000 328i) . I read code 1397 > ( Camshaft pos. sensor) along with code 1498. Does anyone know what 1498 > is? I saw some info on the web pointing to a transmission fault but that > was for a Mini. It said 1498 was for Mini's only - not BMW's. The car runs > and drives fine and has 55k miles. > > How long can I drive with one of the camshaft sensors out? I heard the > usual failure mode is oil ingestion due to cracks on the tip?? > > Thanks for any info. > > Jeff > |
#6
|
|||
|
|||
2000 E46 OBD code 1498
"Dave Plowman (News)" > wrote in message ... > In article >, > Jeff Strickland > wrote: >> The Cam Sensor does a similar job as the points used to do way back when >> they still used points. > > Not so - it's the crank sensor which basically times the spark. More > accurate than a sensor driven via chains etc which stretch. The cam sensor > - ignition wise - tells which stroke the engine is on as the crank turns > twice per cylinder cycle. > But Dave, the points time the spark. Granted, the job is done differently, but when looking for the cam sensor, one would look in essentially the same place as one might look for points. The package might be different, but the location and job is pretty much the same. Distributors (points) have always been driven by a gear. I've never seen an application where this job would be done via a chain-driven mechanism. |
#7
|
|||
|
|||
2000 E46 OBD code 1498
Thanks all for the great replies. I did read the codes from the OBDII port
under the drivers dash using an Actron code reader. Guess I'll order a cam sensor today. Thanks again Jeff > "JeffC" > wrote in message > ... >> Hi - the check engine light came on today (2000 328i) . I read code 1397 >> ( Camshaft pos. sensor) along with code 1498. Does anyone know what 1498 >> is? I saw some info on the web pointing to a transmission fault but that >> was for a Mini. It said 1498 was for Mini's only - not BMW's. The car >> runs and drives fine and has 55k miles. >> >> How long can I drive with one of the camshaft sensors out? I heard the >> usual failure mode is oil ingestion due to cracks on the tip?? >> >> Thanks for any info. >> >> Jeff >> > > |
#8
|
|||
|
|||
2000 E46 OBD code 1498
In article >,
Jeff Strickland > wrote: > "Dave Plowman (News)" > wrote in message > ... > > In article >, > > Jeff Strickland > wrote: > >> The Cam Sensor does a similar job as the points used to do way back > >> when they still used points. > > > > Not so - it's the crank sensor which basically times the spark. More > > accurate than a sensor driven via chains etc which stretch. The cam > > sensor - ignition wise - tells which stroke the engine is on as the > > crank turns twice per cylinder cycle. > > > But Dave, the points time the spark. Granted, the job is done > differently, but when looking for the cam sensor, one would look in > essentially the same place as one might look for points. The package > might be different, but the location and job is pretty much the same. You've not understood what I've written. It's a combination of the two, but the crank one actually triggers the spark. It's perfectly possible to trigger the ignition from the crank only - the Ford EDIS system does this - and I don't know of any that uses a cam position only one. > Distributors (points) have always been driven by a gear. I've never seen > an application where this job would be done via a chain-driven mechanism. Most distributors are gear driven off the camshaft - which in turn is usually driven by a chain or belt. So any wear in that chain effects the ignition timing. That didn't much matter when points and timing were checked every few thousand miles, and there were no emission controls, but these days ignition systems are expected to last the life of the car with no attention, and provide accurate timing throughout. -- *It's a thankless job, but I've got a lot of Karma to burn off Dave Plowman London SW To e-mail, change noise into sound. |
#9
|
|||
|
|||
2000 E46 OBD code 1498
"Dave Plowman (News)" > wrote in message ... > In article >, > Jeff Strickland > wrote: >> "Dave Plowman (News)" > wrote in message >> ... >> > In article >, >> > Jeff Strickland > wrote: >> >> The Cam Sensor does a similar job as the points used to do way back >> >> when they still used points. >> > >> > Not so - it's the crank sensor which basically times the spark. More >> > accurate than a sensor driven via chains etc which stretch. The cam >> > sensor - ignition wise - tells which stroke the engine is on as the >> > crank turns twice per cylinder cycle. >> > > >> But Dave, the points time the spark. Granted, the job is done >> differently, but when looking for the cam sensor, one would look in >> essentially the same place as one might look for points. The package >> might be different, but the location and job is pretty much the same. > > You've not understood what I've written. It's a combination of the two, > but the crank one actually triggers the spark. It's perfectly possible to > trigger the ignition from the crank only - the Ford EDIS system does this > - and I don't know of any that uses a cam position only one. > >> Distributors (points) have always been driven by a gear. I've never seen >> an application where this job would be done via a chain-driven mechanism. > > Most distributors are gear driven off the camshaft - which in turn is > usually driven by a chain or belt. So any wear in that chain effects the > ignition timing. That didn't much matter when points and timing were > checked every few thousand miles, and there were no emission controls, but > these days ignition systems are expected to last the life of the car with > no attention, and provide accurate timing throughout. > No matter, the discussion is the source of the P1397 code, and that comes from the cam sensor, and that is located in a position one might expcet to find the points -- if they still used points (which we all know they don't use and haven't used for a very long time, but gives one an idea of where to locate the cam sensor). |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Code P1131 on 2000 GT question | Mark G7#9 | Ford Mustang | 3 | April 8th 09 12:48 AM |
Transmission code 2000 S4 | [email protected] | Audi | 3 | July 18th 08 12:24 PM |
2000 TDI DTC code question | Peter Parker | VW water cooled | 3 | February 4th 08 09:16 PM |
2000 A4 1.8T trouble code | KWS | Audi | 5 | October 27th 05 06:45 AM |
Code P1133 on 2000 Saturn SL | Edward Crismond | Saturn | 1 | February 3rd 05 01:25 AM |