If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
cautionary timing belt tale
recently, i decided to check ignition timing on my 89 civic & noticed
the pulley wheel marks skipping about all over the place. this is common on old cars with chain driven cams at high mileage, but on toothed belts, this is very rare. so, finally decided to do preventive work, including timing belt & investigate. made a highly un-nerving discovery. the old belt had never been tensioned correctly! in fact, it was so loose, turning the crank in reverse made the belt skip teeth! i'd put about 14k on this car since i got it, including regular red lines, & it had never been a problem. incredible. this is all the more amazing because if you know what to do, properly tensioning the belt takes less than 5 minutes. but evidently, this is was not done here. bottom line: be careful out there folks. this could have been one expensive way to remember to always have a used car checked when you first get it. i knew better, but was moving house about the time i got the car, so had other things on my mind. how to tension the timing belt: 1. there's a 14mm bolt with it's head inside the timing belt cover about half way down. covered by a little grommet. remove the grommet & place ratchet in hole. unscrew bolt until it's just loose. 2. turn crank with the pulley bolt _anti-clockwise_. turn until you reach one of the resistance points in the cycle, one where you're resisting the cam springs. 3. tighten the tensioner bolt. the tensioner pulley is spring loaded so tension should be correct. if you've changed your own belt, you can be confident this works because you've seen it in action with the covers off. of not, have faith, it works beautifully. if you have air conditioning, you need to access from underneath because the compressor is in the way for top access. the problem arose because the tensioner spring is not very strong and unless you follow book procedure & rotate the crank a few times to let it settle & maintain tension on the "pulling" side, you get belt tension on the "return" side & this works against the tension spring & allows the pulling side to be slack. this then gets locked in when the tensioner bolt is tightened. so, job now done, but i mention it because i've seen a number of "skipped teeth" postings here. hopefully this helps people get it right. |
Ads |
#2
|
|||
|
|||
jim beam > wrote in
news:1110771753.9321a7ba9ee55d07811f463e17b13364@t eranews: > how to tension the timing belt: > > 1. there's a 14mm bolt with it's head inside the timing belt cover about > half way down. covered by a little grommet. remove the grommet & place > ratchet in hole. unscrew bolt until it's just loose. > > 2. turn crank with the pulley bolt _anti-clockwise_. turn until you > reach one of the resistance points in the cycle, one where you're > resisting the cam springs. > > 3. tighten the tensioner bolt. the tensioner pulley is spring loaded so > tension should be correct. You can also tap the timing belt cover (or the bolt itself if you can reach it) lightly once or twice with the bolt loose. This will help shock the tensioner into climbing a bit higher on its spring, increasing tension on the belt. Now you just have to make sure there's a bit of slack still left in the belt, and that there's no whining or whirring noise from the belt with the engine running. If the belt is now too tight, loosen that bolt again, then carefully turn the crank _clockwise_ one or two teeth (the cams will not turn). This will pull the tensioner back down again, and you can start over. -- TeGGeR® The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Timing belt / water pump | mpet500 | Honda | 15 | March 16th 05 04:18 PM |
1992 Camry Timing Belt | [email protected] | Technology | 4 | March 8th 05 03:11 PM |
'89 525i timing belt woes | [email protected] | BMW | 15 | December 31st 04 06:37 PM |
Is the auxiliary shaft belt the second timing belt? | [email protected] | Honda | 1 | December 31st 04 06:20 AM |
Honda Passport - Timing Belt | ajpdla | Honda | 3 | December 12th 04 03:12 AM |