If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
V-6 in '08 Wrangler???
A friend tells me that the engine in my new Wrangler is made by Mitsubushi.
Is he correct? All I've heard is that it's a "good" engine and that it's used in most Chrysler-made vans and has been around for a long time. |
Ads |
#2
|
|||
|
|||
V-6 in '08 Wrangler???
Yup, it would appear you now have a mini van engine. No more crawling
up the sides of sand pits or over rocks at 400-500 rpm like the old 6 would do. You now need tire spinning, hole digging, rpm to get anyplace. Probably better on the highway. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's - Gone to the rust pile... Jack Carter wrote: > A friend tells me that the engine in my new Wrangler is made by Mitsubushi. > Is he correct? All I've heard is that it's a "good" engine and that it's > used in most Chrysler-made vans and has been around for a long time. > > |
#3
|
|||
|
|||
V-6 in '08 Wrangler???
Maybe you should check out the gear ratios in the 6-speed transmission and
then take one for a test drive - preferably one with the optional 3.73 axles. If you're open minded - as opposed to empty headed - you might change your mind! "Mike Romain" > wrote in message ng.com... > Yup, it would appear you now have a mini van engine. No more crawling up > the sides of sand pits or over rocks at 400-500 rpm like the old 6 would > do. You now need tire spinning, hole digging, rpm to get anyplace. > > Probably better on the highway. > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's - Gone to the rust pile... > > > Jack Carter wrote: >> A friend tells me that the engine in my new Wrangler is made by >> Mitsubushi. Is he correct? All I've heard is that it's a "good" engine >> and that it's used in most Chrysler-made vans and has been around for a >> long time. |
#4
|
|||
|
|||
V-6 in '08 Wrangler???
On Oct 25, 9:40 am, "Jack Carter" >
wrote: > A friend tells me that the engine in my new Wrangler is made by Mitsubushi. > Is he correct? All I've heard is that it's a "good" engine and that it's > used in most Chrysler-made vans and has been around for a long time. JP Magazine published a torque and HP curve chart from an independent dyno test showing both the 4.0 and the new 3.8. The curves are just about exactly the same util up high in RPM, then the 3.8 has a bit more torque and hp. I have also read that it takes about 5000 miles to break into this level of performance so in test drives of new vehicles the engine tends to feel sluggish. Actually, on paper, the torque curve of the 4.0 is crappy compared to the 258 and even the old L and F head engines in terms of peak torque RPM. However, in practice, jeepers love the 4.0. |
#5
|
|||
|
|||
V-6 in '08 Wrangler???
On Oct 25, 7:40 am, "Jack Carter" >
wrote: > A friend tells me that the engine in my new Wrangler is made by Mitsubushi. > Is he correct? All I've heard is that it's a "good" engine and that it's > used in most Chrysler-made vans and has been around for a long time. since you already own the vehicle, why worry about it? Especially if you just bought it with the lifetime warranty. |
#6
|
|||
|
|||
V-6 in '08 Wrangler???
I have not seen the dyno results you say, maybe if you could post a link.
But I have to note, that usually dyno results range from around 2000 rpm and up. They don't tell you what is going on bellow 2000 rpm, and most of the driving is in the 1200 - 2500 rpm range. Bill Spiliotopoulos, '96 XJ, '06 TJ. "nrs" > wrote in message oups.com... > On Oct 25, 9:40 am, "Jack Carter" > > wrote: >> A friend tells me that the engine in my new Wrangler is made by >> Mitsubushi. >> Is he correct? All I've heard is that it's a "good" engine and that it's >> used in most Chrysler-made vans and has been around for a long time. > > JP Magazine published a torque and HP curve chart from an independent > dyno test showing both the 4.0 and the new 3.8. The curves are just > about exactly the same util up high in RPM, then the 3.8 has a bit > more torque and hp. I have also read that it takes about 5000 miles > to break into this level of performance so in test drives of new > vehicles the engine tends to feel sluggish. > > Actually, on paper, the torque curve of the 4.0 is crappy compared to > the 258 and even the old L and F head engines in terms of peak torque > RPM. However, in practice, jeepers love the 4.0. > > > |
#7
|
|||
|
|||
V-6 in '08 Wrangler???
Mike is right. There is no substitute for a low-revving, high torque engine
with high rotational mass. Simple physics says Mike is right and you are easily persuaded by marketing smoke and mirrors. Cheers, Earle "Jack Carter" > wrote in message . .. > Maybe you should check out the gear ratios in the 6-speed transmission and > then take one for a test drive - preferably one with the optional 3.73 > axles. If you're open minded - as opposed to empty headed - you might > change your mind! > > > "Mike Romain" > wrote in message > ng.com... >> Yup, it would appear you now have a mini van engine. No more crawling up >> the sides of sand pits or over rocks at 400-500 rpm like the old 6 would >> do. You now need tire spinning, hole digging, rpm to get anyplace. >> >> Probably better on the highway. >> >> Mike >> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 >> 88 Cherokee 235 BFG AT's - Gone to the rust pile... >> >> >> Jack Carter wrote: >>> A friend tells me that the engine in my new Wrangler is made by >>> Mitsubushi. Is he correct? All I've heard is that it's a "good" engine >>> and that it's used in most Chrysler-made vans and has been around for a >>> long time. > > |
#8
|
|||
|
|||
V-6 in '08 Wrangler???
On Oct 25, 11:54 am, "Bill Spiliotopoulos" > wrote:
> I have not seen the dyno results you say, maybe if you could post a link. > But I have to note, that usually dyno results range from around 2000 rpm and > up. They don't tell you what is going on bellow 2000 rpm, and most of the > driving is in the 1200 - 2500 rpm range. > > Bill Spiliotopoulos, > '96 XJ, > '06 TJ. > > "nrs" > wrote in message > > oups.com... > > > > > On Oct 25, 9:40 am, "Jack Carter" > > > wrote: > >> A friend tells me that the engine in my new Wrangler is made by > >> Mitsubushi. > >> Is he correct? All I've heard is that it's a "good" engine and that it's > >> used in most Chrysler-made vans and has been around for a long time. > > > JP Magazine published a torque and HP curve chart from an independent > > dyno test showing both the 4.0 and the new 3.8. The curves are just > > about exactly the same util up high in RPM, then the 3.8 has a bit > > more torque and hp. I have also read that it takes about 5000 miles > > to break into this level of performance so in test drives of new > > vehicles the engine tends to feel sluggish. > > > Actually, on paper, the torque curve of the 4.0 is crappy compared to > > the 258 and even the old L and F head engines in terms of peak torque > > RPM. However, in practice, jeepers love the 4.0.- Hide quoted text - > > - Show quoted text - Some of my facts were off due to bad memory but here is the link to the chart. It actually goes to low RPMs. http://www.jpmagazine.com/projectbui.../photo_03.html |
#9
|
|||
|
|||
V-6 in '08 Wrangler???
You feel the need to insult my opinion just because you got took and
didn't look under the hood? I feel sorry for you, but Chrysler 'did' make that special oil additive 'just' for the Mitsubishi smokers so it might last a little while... ;-) So I have the sand pit wall in mind if you want a test, bring on the mini van engines!!! Seriously, it would be fun. I am in the Toronto Canada area and love to sit at the top taking photos of folks trying to make it. I'll even post the photo album up. Mike Jack Carter wrote: > Maybe you should check out the gear ratios in the 6-speed transmission and > then take one for a test drive - preferably one with the optional 3.73 > axles. If you're open minded - as opposed to empty headed - you might change > your mind! > > > "Mike Romain" > wrote in message > ng.com... >> Yup, it would appear you now have a mini van engine. No more crawling up >> the sides of sand pits or over rocks at 400-500 rpm like the old 6 would >> do. You now need tire spinning, hole digging, rpm to get anyplace. >> >> Probably better on the highway. >> >> Mike >> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 >> 88 Cherokee 235 BFG AT's - Gone to the rust pile... >> >> >> Jack Carter wrote: >>> A friend tells me that the engine in my new Wrangler is made by >>> Mitsubushi. Is he correct? All I've heard is that it's a "good" engine >>> and that it's used in most Chrysler-made vans and has been around for a >>> long time. > > |
#10
|
|||
|
|||
V-6 in '08 Wrangler???
Ditto. But I do love spinning tire, just it takes a heck of a lot more
horsepower than that puny V6: http://www.billhughes.com/pismo.htm God Bless America, Bill O|||||||O "Earle Horton" > wrote in message ... > Mike is right. There is no substitute for a low-revving, high torque engine > with high rotational mass. Simple physics says Mike is right and you are > easily persuaded by marketing smoke and mirrors. > > Cheers, > > Earle -- Posted via a free Usenet account from http://www.teranews.com |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
2006 Wrangler rims fit 94 wrangler?? Anyone have answer? | Jeeeprs | Jeep | 1 | May 18th 07 03:37 AM |
2007 Jeep Wrangler Promo 2007 Jeep Wrangler 28.jpg | DKR[_2_] | Auto Photos | 0 | January 1st 07 08:55 PM |
2007 Jeep Wrangler Promo 2007 Jeep Wrangler 10.jpg | DKR[_2_] | Auto Photos | 0 | January 1st 07 08:53 PM |
2007 Jeep Wrangler Promo 2007 Jeep Wrangler 1.jpg | DKR[_2_] | Auto Photos | 0 | January 1st 07 08:53 PM |
2005 Wrangler Soft top on 99 Wrangler | Ice | Jeep | 7 | March 6th 06 03:40 AM |