If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
NAPA vs. Autozone vs. O'Reilly... price and quality?
Using online catalogues, i've priced out the parts to rebuild the
front end on my truck. (In-store pricing might be slightly different) This will mean 2 upper control arm assys, 2 lower ball joints, control arm bushings all around, and inner and outer tie rod ends for both sides. At NAPA, it's about $450 for parts, at Autozone about $370, and O'Reilly will be just under $300. These are all using store-branded parts, not the generic (in NAPA's case) or Moog brand (in O'Reilly's case). Is there any significant reason for this, or any major quality differences? We're talking about a bunch of machined metal and rubber, not microcontrollers. For all I know they could all be made by the same contractor. Tempting as it it is, I see entire kits of everything listed above on eBay for under $100. They're generic names, but no more generic sounding to me than the store brands. Any thoughts? Thanks. |
Ads |
#2
|
|||
|
|||
NAPA vs. Autozone vs. O'Reilly... price and quality?
You might also check Advance auto parts, if there is a store in your
area.Or, http://www.jcwhitney.com Call their toll free number, ask them to send you a free catalog, pertaining to your interest. cuhulin |
#4
|
|||
|
|||
NAPA vs. Autozone vs. O'Reilly... price and quality?
On Mar 16, 12:29*pm, phaeton > wrote:
> Using online catalogues, i've priced out the parts to rebuild the > front end on my truck. (In-store pricing might be slightly different) > This will mean 2 upper control arm assys, 2 lower ball joints, control > arm bushings all around, and inner and outer tie rod ends for both > sides. > > At NAPA, it's about $450 for parts, at Autozone about $370, and > O'Reilly will be just under $300. *These are all using store-branded > parts, not the generic (in NAPA's case) or Moog brand (in O'Reilly's > case). *Is there any significant reason for this, or any major quality > differences? *We're talking about a bunch of machined metal and > rubber, not microcontrollers. *For all I know they could all be made > by the same contractor. > > Tempting as it it is, I see entire kits of everything listed above on > eBay for under $100. *They're generic names, but no more generic > sounding to me than the store brands. > > Any thoughts? > > Thanks. What's the price for Moog branded parts? I'd feel more comfortable with those than any "generic" or "store" brand. yes, these parts are not technically challenging to produce, but if corners were cut and/or inferior materials were used, the consequences of failure (esp. a ball joint or tie rod end) are not pretty. nate |
#5
|
|||
|
|||
NAPA vs. Autozone vs. O'Reilly... price and quality?
People often view NAPA first, Autozone second, and Oreilly last in terms
of dependability and quality. Whether true or not, this is a common feeling among mechanics and amateurs. If you buy their cheapest parts, you may get some poor remanufactured parts in some cases, or even Made in China. Not all China stuff is crap, but a lot IS. I have heard that Advance might be a higher level than Autozone but cant confirm. You may be able to find some of the online parts stores that can get you high quality parts at good prices. |
#6
|
|||
|
|||
NAPA vs. Autozone vs. O'Reilly... price and quality?
On Mar 16, 2:28*pm, "hls" > wrote:
> People often view NAPA first, Autozone second, and Oreilly last in terms > of dependability and quality. *Whether true or not, this is a common feeling > among mechanics and amateurs. > > If you buy their cheapest parts, you may get some poor remanufactured > parts in some cases, or even Made in China. * Not all China stuff is crap, > but a lot *IS. > > I have heard that Advance might be a higher level than Autozone but cant > confirm. > > You may be able to find some of the online parts stores that can get you > high quality parts at good prices. good point, I'd price out name brand stuff from Rock Auto, might be even cheaper. I got a complete brake job for my F-150 for only a couple hundred bucks (calipers, pads, shoes, rotors, seals, hoses, hardware kits, etc - the only things I did not replace were the rear drums and the bearings, because the bearings had just been replaced) by picking up name brand (Raybestos and/or Wagner, usually) stuff on closeout. nate |
#7
|
|||
|
|||
NAPA vs. Autozone vs. O'Reilly... price and quality?
On Tue, 16 Mar 2010 09:29:16 -0700 (PDT), phaeton
> wrote: >Using online catalogues, i've priced out the parts to rebuild the >front end on my truck. (In-store pricing might be slightly different) >This will mean 2 upper control arm assys, 2 lower ball joints, control >arm bushings all around, and inner and outer tie rod ends for both >sides. > >At NAPA, it's about $450 for parts, at Autozone about $370, and >O'Reilly will be just under $300. These are all using store-branded >parts, not the generic (in NAPA's case) or Moog brand (in O'Reilly's >case). Is there any significant reason for this, or any major quality >differences? We're talking about a bunch of machined metal and >rubber, not microcontrollers. For all I know they could all be made >by the same contractor. > >Tempting as it it is, I see entire kits of everything listed above on >eBay for under $100. They're generic names, but no more generic >sounding to me than the store brands. > >Any thoughts? > >Thanks. First off, until the Congress reverses some the lying labeling legislation they've installed to hoodwink buyers, it's often hard to tell where these parts are made. That's how the sellers want it. Besides that, it doesn't usually matter in terms of quality. I did ball joints and tie rod ends on my Lumina last year and had the O'Reilly parts guy bring them out for me. I went with Moog ends and the O'Reilly brand - ProParts? - ball joints. Might have looked at some TRW parts too. The Moog ends looked better enough to justify maybe an 86 buck premium each, the joints looked the same, and didn't justify the maybe 20 buck each premium. But that's all my own voodoo. It's not like I could take them apart or do Rockwell tests on them. My kid does suspensions all day in a shop that only does suspensions, 99% trucks, from fire trucks and garbage trucks to pick-ups. I just called him to ask what they use. It's either Moog or OEM. And he really doesn't know where either is made. He "thinks" Moog are Made in U.S.A. But he's not sure. And he's not sure that Moog are the best either. Just that's what they use. Maybe they get a volume discount. That eBay stuff just sounds too cheap. Maybe hammered out in some Indian shipwrecker yard. The Indian billionaire that owns the operation could pay off the right Congress critters or regulator to get any junk into the country. I'd go with the cheapest from a distributor than can be easily sued if the parts cause an accident. That's the only fear that keeps them half-way honest. Otherwise there's probably not much difference. Check that they at least have zerk holes tapped in them. As I recall, the O'Reilly non-Moog ends didn't have them. --Vic |
#8
|
|||
|
|||
NAPA vs. Autozone vs. O'Reilly... price and quality?
On Tue, 16 Mar 2010 16:00:23 -0500, Vic Smith
> wrote: >The Moog ends looked better enough to justify maybe an 86 buck premium Oops. 8 buck premium. |
#9
|
|||
|
|||
NAPA vs. Autozone vs. O'Reilly... price and quality?
You might also look at,
http://www.who-sells-it.com Definetly, use parts that have Alemites (some people call them Zerks) on them.You can grease them rugularly with a grease gun. Moog and TRW have been in business for many years.I would go for OEM parts. cuhulin |
#10
|
|||
|
|||
NAPA vs. Autozone vs. O'Reilly... price and quality?
On Mar 16, 12:29*pm, phaeton > wrote:
> Using online catalogues, i've priced out the parts to rebuild the > front end on my truck. (In-store pricing might be slightly different) > This will mean 2 upper control arm assys, 2 lower ball joints, control > arm bushings all around, and inner and outer tie rod ends for both > sides. > > At NAPA, it's about $450 for parts, at Autozone about $370, and > O'Reilly will be just under $300. *These are all using store-branded > parts, not the generic (in NAPA's case) or Moog brand (in O'Reilly's > case). *Is there any significant reason for this, or any major quality > differences? *We're talking about a bunch of machined metal and > rubber, not microcontrollers. *For all I know they could all be made > by the same contractor. > > Tempting as it it is, I see entire kits of everything listed above on > eBay for under $100. *They're generic names, but no more generic > sounding to me than the store brands. > > Any thoughts? > > Thanks. Everything is still made in China, or some other Country. Stay away from the Generic. Bottom line is you get what you pay for.. If you plan on selling the car buy the cheap stuff otherwise stick with the name brands. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Discount Garmin GPS, Quality At A Great Price | virig[_2_] | Technology | 1 | August 31st 08 04:24 PM |
Discount Garmin GPS, Quality At A Great Price | virig[_2_] | Chrysler | 0 | August 31st 08 09:44 AM |
Discount Garmin GPS, Quality At A Great Price | virig[_2_] | Jeep | 0 | August 31st 08 09:39 AM |
AWA [OFFER] quality product and commpetitive price | [email protected] | General | 0 | December 7th 05 03:02 AM |