If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Clutch bolts and locktite
Which is best for dropping the transmission?
Do you remove the crossmember, the bracket, or just the transmission mount? * Crossmember http://www.bild.me/bild.php?file=6290082bracket03.jpg * Bracket http://www.bild.me/bild.php?file=4222146bracket02.jpg * Mount http://www.bild.me/bild.php?file=6137530bracket01.jpg Also, do you locktite the bolts when you re-install? (What color?) http://www.bild.me/bild.php?file=9054142locktite01.jpg |
Ads |
#2
|
|||
|
|||
Clutch bolts and locktite
On 7/22/18 4:10 AM, Arlen Holder wrote:
> Which is best for dropping the transmission? > > Do you remove the crossmember, the bracket, or just the transmission mount? > * Crossmember http://www.bild.me/bild.php?file=6290082bracket03.jpg > * Bracket http://www.bild.me/bild.php?file=4222146bracket02.jpg > * Mount http://www.bild.me/bild.php?file=6137530bracket01.jpg > > Also, do you locktite the bolts when you re-install? (What color?) > http://www.bild.me/bild.php?file=9054142locktite01.jpg > If you have to ask those questions, the job is above your pay grade... -- The fastest way to stop a bad guy with a gun is a good guy with a gun. |
#3
|
|||
|
|||
Clutch bolts and locktite
On Sun, 22 Jul 2018 08:10:10 -0000 (UTC), Arlen Holder
> wrote: >Which is best for dropping the transmission? > >Do you remove the crossmember, the bracket, or just the transmission mount? >* Crossmember http://www.bild.me/bild.php?file=6290082bracket03.jpg >* Bracket http://www.bild.me/bild.php?file=4222146bracket02.jpg >* Mount http://www.bild.me/bild.php?file=6137530bracket01.jpg > What is the risk off the tranny falling on you? >Also, do you locktite the bolts when you re-install? (What color?) >http://www.bild.me/bild.php?file=9054142locktite01.jpg The bolts have a torque range. Torque 'em and forget it. |
#4
|
|||
|
|||
Clutch bolts and locktite
On 22 Jul 2018 09:18:06 GMT, Oren wrote:
> What is the risk off the tranny falling on you? > >>Also, do you locktite the bolts when you re-install? (What color?) >>http://www.bild.me/bild.php?file=9054142locktite01.jpg > > The bolts have a torque range. Torque 'em and forget it. I found out that almost nobody uses locktite on transmission bolts. Flywheel yes. Transmission no. I still might locktite it though, just because it's hard to get to the upper 17mm transmission bolts on the bell housing (I had to use a series of half-inch extensions 30" long with a swivel as the 3/8" extensions just twisted more than a quarter turn and were useless). The blue is the locktite I'll buy (I generally never use the stuff but I've never done a transmission before - but I've done everything else that people do as I don't think I've been to a mechanic in two decades and my cars are all that old). http://www.wdarc.org/Loctite%20Guide.pdf I was hoping for more advice here than "if you don't know, then you should" though. Sigh. Anyway, as for the colors, Blue is just help it from coming loose where proper torquing does the work. Red is for permanent install, hard to come off Green is for use on nuts and bolts that are already installed This guide to locktite seems useful. http://www.loctite.com.au/aue/conten...5_Approved.pdf |
#5
|
|||
|
|||
Clutch bolts and locktite
On 07/22/2018 12:37 PM, Arlen Holder wrote:
> Anyway, as for the colors, > Blue is just help it from coming loose where proper torquing does the work. > Red is for permanent install, hard to come off > Green is for use on nuts and bolts that are already installed If you're going to use any, blue is the way to go or the next time you remove the transmission you'll be in there with a torch heating up the bolts to soften the red. I have never used LocTite on transmission, bellhousing, or pressure plate fasteners. |
#6
|
|||
|
|||
Clutch bolts and locktite
On 7/22/2018 4:07 PM, rbowman wrote:
> On 07/22/2018 12:37 PM, Arlen Holder wrote: >> Anyway, as for the colors, >> Blue is just help it from coming loose where proper torquing does the >> work. >> Red is for permanent install, hard to come off >> Green is for use on nuts and bolts that are already installed > > If you're going to use any, blue is the way to go or the next time you > remove the transmission you'll be in there with a torch heating up the > bolts to soften the red. > > I have never used LocTite on transmission, bellhousing, or pressure > plate fasteners. * But damn sure on the nut that holds the compensator sprocket to the crankshaft on your Harley ... -- Snag Yes , I'm old and crochety . Get off my lawn ! |
#7
|
|||
|
|||
Clutch bolts and locktite
On 22 Jul 2018 14:20:55 GMT, Terry Coombs wrote:
>> I have never used LocTite on transmission, bellhousing, or pressure >> plate fasteners. > > * But damn sure on the nut that holds the compensator sprocket to the > crankshaft on your Harley ... Thanks for the locktite advice, where I never use it and I've done a decent amount of work (cooling systems, alternators, belts, tensioners, etc.) where I never before ran into bolts that needed 30 inches of extension to get to, so I'll locktite blue them sparingly. I always buy the tools I need, where right now, I can't think of the tool that I need, but whatever it is, I need it. How on earth do you get the transmission to back away from the engine? I can't budge the thing! It's in neutral. I'm positive all the bolts are off. I'm only somewhat positive that it's level because you can't really easily tell, but it's close enough as I can wiggle it back and forth. If it's hanging up on something, I don't see what. I just can't get any rearward force on that transmission. What tool does that? Here are some pictures showing that it seems to be hanging up on the upper dowel pin, where the lower dowel pin is already out. This is the driver side lower dowel pin, which is already out: <http://www.bild.me/bild.php?file=7254379bellhousing01.jpg> This is the same view showing that the tranmission "appears" level: <http://www.bild.me/bild.php?file=6205540bellhousing02.jpg> This is the passenger side where the dowel pin can be seen up high: <http://www.bild.me/bild.php?file=5277197bellhousing03.jpg> I'm not sure where to place the jack but it's at the transmission waist: <http://www.bild.me/bild.php?file=1315488bellhousing04.jpg> The tool I need is a tool to back the transmission away from the engine. What tool is that? |
#8
|
|||
|
|||
Clutch bolts and locktite
On 07/22/2018 03:20 PM, Terry Coombs wrote:
> > But damn sure on the nut that holds the compensator sprocket to the > crankshaft on your Harley ... Luckily I haven't had to go there yet. I didn't replace the clutch throwout bearing a few years ago but that's no big deal. Grant me the knowledge to put LocTite on the things shouldn't come apart, Never-Seez on the things that should, and the wisdom to know the difference. |
#9
|
|||
|
|||
Clutch bolts and locktite
On 07/22/2018 05:01 PM, Arlen Holder wrote:
> The tool I need is a tool to back the transmission away from the engine. > What tool is that? Are you supporting the engine? |
#10
|
|||
|
|||
Clutch bolts and locktite
On 22 Jul 2018 18:17:06 GMT, rbowman wrote:
> Are you supporting the engine? OH oh.... supporting the engine? I could. I have plenty of floor jacks. It's RWD though. The vehicle is on four jack stands (two on the rear axle and two on front frame points just inside the wheels). I appreciate your question, and my answer is definitely "no", I am not supporting the engine. It didn't occur to me to support the engine so I have to ask why would that help? (I'm not at all against the idea - I just don't understand how it can help?) How would I support the engine so that it would help? |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
94 Explorer Clutch fluid Disappearing & clutch slip | rolleye | Ford Explorer | 1 | July 12th 07 03:43 PM |
AWA [OFFER] Clutch Cover,Clutch Facing | [email protected] | General | 0 | January 15th 06 01:55 PM |
1994 Ford Ranger Clutch slipping when hot- clutch has 1000 miles on it. | RobertJohnC | 4x4 | 1 | November 24th 05 11:43 PM |
Clutch slipping. Clutch cyl or need a new clutch | bobbob1015 | BMW | 6 | May 21st 05 12:19 AM |
Oil Pan bolts? | Paul Brogren | Jeep | 24 | January 27th 05 12:10 AM |