If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
94 Front Pony removal
I want to put a billet grille in my 94 GT, but it looks like you need a
special tool to remove the original pony. It's a six point internal star like screw head with a small center. Looks like the tool would have to be six points with a hole in the middle to clear the small diameter there. Can't grab the outside of the screw because it's a round head screw. Any info is appreciated. |
Ads |
#2
|
|||
|
|||
On Fri, 18 Mar 2005 18:06:05 -0500, 4-2LGW wrote:
> I want to put a billet grille in my 94 GT, but it looks like you need a > special tool to remove the original pony. It's a six point internal star > like screw head with a small center. > > Looks like the tool would have to be six points with a hole in the middle to > clear the small diameter there. Can't grab the outside of the screw because > it's a round head screw. > > Any info is appreciated. Maybe a torx head? Thomas |
#3
|
|||
|
|||
4-2LGW opined in :
> I want to put a billet grille in my 94 GT, but it looks like you need a > special tool to remove the original pony. It's a six point internal > star like screw head with a small center. > > Looks like the tool would have to be six points with a hole in the > middle to clear the small diameter there. Can't grab the outside of the > screw because it's a round head screw. > > Any info is appreciated. > > > That's a security torx screw... it is used due to high theft rate of those ponies. But any punk can go into harbor freight and buy them, other places as well. But why not just go to your favorite Ford service/body shop, ask real nice... -- - Yes, I'm a crusty old geezer curmudgeon.. deal with it! - |
#4
|
|||
|
|||
On Fri, 18 Mar 2005 18:06:05 -0500, "4-2LGW" >
wrote: >I want to put a billet grille in my 94 GT, but it looks like you need a >special tool to remove the original pony. It's a six point internal star >like screw head with a small center. > >Looks like the tool would have to be six points with a hole in the middle to >clear the small diameter there. Can't grab the outside of the screw because >it's a round head screw. > >Any info is appreciated. > It's called a security torx bolt. They sell cheap sets on ebay, less than 10 bucks. Remove NO-SPAM from email address when replying |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Super Beetle brake shoes - are front and rear the same? | Scott H | VW air cooled | 13 | March 15th 05 03:53 PM |
how did Dilbert learn in front of all the kettles? We can't nibble plates unless Alexis will daily recollect afterwards | [email protected] | Technology | 0 | January 15th 05 01:56 PM |
4.5 bolt front hubs/rear axles to 5.5 bolt front hubs/rear axles? | zion_curtain | Ford Explorer | 1 | January 4th 05 06:57 AM |
Looking for directions to service front hubs (1994 4x4) | Chris | Ford Explorer | 1 | November 3rd 04 04:49 PM |
CJ8 front springs & stabilizer bar removal | Michael Pomeroy | 4x4 | 1 | July 5th 04 05:01 PM |