A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » Mazda
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Failed MD inspection



 
 
Thread Tools Display Modes
  #1  
Old October 26th 12, 03:34 PM posted to rec.autos.makers.mazda.miata
Frank Berger[_2_]
external usenet poster
 
Posts: 18
Default Failed MD inspection

1. Rear window is tinted - that's against MD law. Have to have the tint
removed.
2. Car is too low. I assume (hope) putting pack the 17" wheels will make
it legal.
3. Right tail light is missing. Not burned out, housing is missing. Never
noticed that.

Grrr.

Ads
  #2  
Old October 27th 12, 06:57 AM posted to rec.autos.makers.mazda.miata
charlie
external usenet poster
 
Posts: 66
Default Failed MD inspection

On 10/26/2012 10:34 AM, Frank Berger wrote:
> 1. Rear window is tinted - that's against MD law. Have to have the
> tint removed.
> 2. Car is too low. I assume (hope) putting pack the 17" wheels will
> make it legal.
> 3. Right tail light is missing. Not burned out, housing is missing.
> Never noticed that.
>
> Grrr.


In Georgia, the rear window tint will often result in a ticket.
The tail light bit is understandable.
Ride height too low? I haven't heard of that one!
We've got a bunch of red necks/swamp rats that jack pickups up several
feet, beyond what I always thought was allowable, and I've not heard of
that causing tickets.

The state I grew up in, Illinois, used to have a law that the license
plates had to be a minimum distance from the ground. The front plate on
a Miata passed if the stock mount was used, and might not if it was
moved down from the mouth.

How can the housing be missing? What attaches the tail light lens to the
body?
  #3  
Old October 27th 12, 07:17 AM posted to rec.autos.makers.mazda.miata
charlie
external usenet poster
 
Posts: 66
Default Failed MD inspection

On 10/27/2012 1:57 AM, charlie wrote:
> On 10/26/2012 10:34 AM, Frank Berger wrote:
>> 1. Rear window is tinted - that's against MD law. Have to have the
>> tint removed.
>> 2. Car is too low. I assume (hope) putting pack the 17" wheels will
>> make it legal.
>> 3. Right tail light is missing. Not burned out, housing is missing.
>> Never noticed that.
>>
>> Grrr.

>
> In Georgia, the rear window tint will often result in a ticket.
> The tail light bit is understandable.
> Ride height too low? I haven't heard of that one!
> We've got a bunch of red necks/swamp rats that jack pickups up several
> feet, beyond what I always thought was allowable, and I've not heard of
> that causing tickets.
>
> The state I grew up in, Illinois, used to have a law that the license
> plates had to be a minimum distance from the ground. The front plate on
> a Miata passed if the stock mount was used, and might not if it was
> moved down from the mouth.
>
> How can the housing be missing? What attaches the tail light lens to the
> body?



You can remove the tint yourself if you have something that creates
steam. Warm/to hot very moist air starts the process, and makes removal
much easier. Dish washing soap and water, with something like Windex, or
a very small amount of ammonia added to the dish washing solution also
helps, and should be repeatedly sprayed on the film. Patience is the
word. Don't scrape any heating grid elements. Generally, you would get a
corner of the film to lift, then spray the warm/solution on followed by
steam, then, after a bit, gently pull on the corner until you feel a
change. Spray some more solution on, add more steam, wait, and as the
film loosens, gently pull again. Once the film is off, there may be some
of the glue remaining. The same process can be used to remove it. You
can also score the film with a razor blade to help the solution/steam
penetrate, but it's easy to scratch the glass or the heat grid elements.

If you have a plastic window, test the solution on a small unimportant
area first. Ammonia can cause problems with some plastics and fabrics.
With the plastic windows, and high heat areas like Texas, some plastic
films can
be a real problem to remove, and cause window replacement to be necessary.
  #4  
Old October 28th 12, 02:16 AM posted to rec.autos.makers.mazda.miata
Frank Berger[_2_]
external usenet poster
 
Posts: 18
Default Failed MD inspection

charlie wrote:
> On 10/26/2012 10:34 AM, Frank Berger wrote:
>> 1. Rear window is tinted - that's against MD law. Have to have the
>> tint removed.
>> 2. Car is too low. I assume (hope) putting pack the 17" wheels will
>> make it legal.
>> 3. Right tail light is missing. Not burned out, housing is missing.
>> Never noticed that.
>>
>> Grrr.

>
> In Georgia, the rear window tint will often result in a ticket.
> The tail light bit is understandable.
> Ride height too low? I haven't heard of that one!
> We've got a bunch of red necks/swamp rats that jack pickups up several
> feet, beyond what I always thought was allowable, and I've not heard
> of that causing tickets.
>
> The state I grew up in, Illinois, used to have a law that the license
> plates had to be a minimum distance from the ground. The front plate
> on a Miata passed if the stock mount was used, and might not if it was
> moved down from the mouth.
>
> How can the housing be missing? What attaches the tail light lens to
> the body?


Maryland says from the center of the headlight to the ground can't be less
than 24".

the light: there is no lens. I don't know what happened to it. There's
just a hole. I bought the car used in CA a couple of years ago. For all I
know, it was never there. Though I would think the Texas inspections would
have caught that.

  #5  
Old October 28th 12, 02:18 AM posted to rec.autos.makers.mazda.miata
Frank Berger[_2_]
external usenet poster
 
Posts: 18
Default Failed MD inspection

charlie wrote:
> On 10/27/2012 1:57 AM, charlie wrote:
>> On 10/26/2012 10:34 AM, Frank Berger wrote:
>>> 1. Rear window is tinted - that's against MD law. Have to have the
>>> tint removed.
>>> 2. Car is too low. I assume (hope) putting pack the 17" wheels
>>> will make it legal.
>>> 3. Right tail light is missing. Not burned out, housing is
>>> missing. Never noticed that.
>>>
>>> Grrr.

>>
>> In Georgia, the rear window tint will often result in a ticket.
>> The tail light bit is understandable.
>> Ride height too low? I haven't heard of that one!
>> We've got a bunch of red necks/swamp rats that jack pickups up
>> several feet, beyond what I always thought was allowable, and I've
>> not heard of that causing tickets.
>>
>> The state I grew up in, Illinois, used to have a law that the license
>> plates had to be a minimum distance from the ground. The front plate
>> on a Miata passed if the stock mount was used, and might not if it
>> was moved down from the mouth.
>>
>> How can the housing be missing? What attaches the tail light lens to
>> the body?

>
>
> You can remove the tint yourself if you have something that creates
> steam. Warm/to hot very moist air starts the process, and makes
> removal much easier. Dish washing soap and water, with something like
> Windex, or a very small amount of ammonia added to the dish washing
> solution also helps, and should be repeatedly sprayed on the film.
> Patience is the word. Don't scrape any heating grid elements.
> Generally, you would get a corner of the film to lift, then spray the
> warm/solution on followed by steam, then, after a bit, gently pull on
> the corner until you feel a change. Spray some more solution on, add
> more steam, wait, and as the film loosens, gently pull again. Once
> the film is off, there may be some of the glue remaining. The same
> process can be used to remove it. You can also score the film with a razor
> blade to help the solution/steam
> penetrate, but it's easy to scratch the glass or the heat grid
> elements.
> If you have a plastic window, test the solution on a small unimportant
> area first. Ammonia can cause problems with some plastics and fabrics.
> With the plastic windows, and high heat areas like Texas, some plastic
> films can
> be a real problem to remove, and cause window replacement to be
> necessary.


This is a glass window on a 2004 MSM. The car was bought new in CA. Don't
know if the tint was aftermarket or what. Thanks for the guide to removing
it, but I think I'll leave this one to a pro. First we have to get
through the hurricane.

  #6  
Old October 28th 12, 09:58 AM posted to rec.autos.makers.mazda.miata
charlie
external usenet poster
 
Posts: 66
Default Failed MD inspection

On 10/27/2012 9:16 PM, Frank Berger wrote:
> charlie wrote:
>> On 10/26/2012 10:34 AM, Frank Berger wrote:
>>> 1. Rear window is tinted - that's against MD law. Have to have the
>>> tint removed.
>>> 2. Car is too low. I assume (hope) putting pack the 17" wheels will
>>> make it legal.
>>> 3. Right tail light is missing. Not burned out, housing is missing.
>>> Never noticed that.
>>>
>>> Grrr.

>>
>> In Georgia, the rear window tint will often result in a ticket.
>> The tail light bit is understandable.
>> Ride height too low? I haven't heard of that one!
>> We've got a bunch of red necks/swamp rats that jack pickups up several
>> feet, beyond what I always thought was allowable, and I've not heard
>> of that causing tickets.
>>
>> The state I grew up in, Illinois, used to have a law that the license
>> plates had to be a minimum distance from the ground. The front plate
>> on a Miata passed if the stock mount was used, and might not if it was
>> moved down from the mouth.
>>
>> How can the housing be missing? What attaches the tail light lens to
>> the body?

>
> Maryland says from the center of the headlight to the ground can't be
> less than 24".
>
> the light: there is no lens. I don't know what happened to it.
> There's just a hole. I bought the car used in CA a couple of years
> ago. For all I know, it was never there. Though I would think the
> Texas inspections would have caught that.


So you are saying that there has been a tail light sided hole on the
Miata since you bought it two years or so ago, and YOU DIDN'T NOTICE?
Sheesh!
  #7  
Old October 28th 12, 01:28 PM posted to rec.autos.makers.mazda.miata
Frank Berger[_2_]
external usenet poster
 
Posts: 18
Default Failed MD inspection

/charlie wrote:/
> On 10/27/2012 9:16 PM, Frank Berger wrote:
>> charlie wrote:
>>> On 10/26/2012 10:34 AM, Frank Berger wrote:
>>>> 1. Rear window is tinted - that's against MD law. Have to have
>>>> the tint removed.
>>>> 2. Car is too low. I assume (hope) putting pack the 17" wheels
>>>> will make it legal.
>>>> 3. Right tail light is missing. Not burned out, housing is
>>>> missing. Never noticed that.
>>>>
>>>> Grrr.
>>>
>>> In Georgia, the rear window tint will often result in a ticket.
>>> The tail light bit is understandable.
>>> Ride height too low? I haven't heard of that one!
>>> We've got a bunch of red necks/swamp rats that jack pickups up
>>> several feet, beyond what I always thought was allowable, and I've
>>> not heard of that causing tickets.
>>>
>>> The state I grew up in, Illinois, used to have a law that the
>>> license plates had to be a minimum distance from the ground. The
>>> front plate on a Miata passed if the stock mount was used, and
>>> might not if it was moved down from the mouth.
>>>
>>> How can the housing be missing? What attaches the tail light lens to
>>> the body?

>>
>> Maryland says from the center of the headlight to the ground can't be
>> less than 24".
>>
>> the light: there is no lens. I don't know what happened to it.
>> There's just a hole. I bought the car used in CA a couple of years
>> ago. For all I know, it was never there. Though I would think the
>> Texas inspections would have caught that.

>
> So you are saying that there has been a tail light sided hole on the
> Miata since you bought it two years or so ago, and YOU DIDN'T NOTICE?
> Sheesh!


I'm saying it's possible.
  #8  
Old November 12th 12, 03:12 PM posted to rec.autos.makers.mazda.miata
Frank Berger[_2_]
external usenet poster
 
Posts: 18
Default Failed MD inspection

Frank Berger wrote:
> /charlie wrote:/
>> On 10/27/2012 9:16 PM, Frank Berger wrote:
>>> charlie wrote:
>>>> On 10/26/2012 10:34 AM, Frank Berger wrote:
>>>>> 1. Rear window is tinted - that's against MD law. Have to have
>>>>> the tint removed.
>>>>> 2. Car is too low. I assume (hope) putting pack the 17" wheels
>>>>> will make it legal.
>>>>> 3. Right tail light is missing. Not burned out, housing is
>>>>> missing. Never noticed that.
>>>>>
>>>>> Grrr.
>>>>
>>>> In Georgia, the rear window tint will often result in a ticket.
>>>> The tail light bit is understandable.
>>>> Ride height too low? I haven't heard of that one!
>>>> We've got a bunch of red necks/swamp rats that jack pickups up
>>>> several feet, beyond what I always thought was allowable, and I've
>>>> not heard of that causing tickets.
>>>>
>>>> The state I grew up in, Illinois, used to have a law that the
>>>> license plates had to be a minimum distance from the ground. The
>>>> front plate on a Miata passed if the stock mount was used, and
>>>> might not if it was moved down from the mouth.
>>>>
>>>> How can the housing be missing? What attaches the tail light lens
>>>> to the body?
>>>
>>> Maryland says from the center of the headlight to the ground can't
>>> be less than 24".
>>>
>>> the light: there is no lens. I don't know what happened to it.
>>> There's just a hole. I bought the car used in CA a couple of years
>>> ago. For all I know, it was never there. Though I would think the
>>> Texas inspections would have caught that.

>>
>> So you are saying that there has been a tail light sided hole on the
>> Miata since you bought it two years or so ago, and YOU DIDN'T NOTICE?
>> Sheesh!

>
> I'm saying it's possible.


Saga of getting the MSM inspected in MD continues. Only one dealer, not too
close, had a tail light assembly in stock. Made 7:30 AM appointment with
him to get light and have him remove tint fromback window. Got there at
7:15, found out the detail guy doesn't come to work until 9:30. The hell
with that. Picked up tail light and went home. Turns out, as per a youtube
video, it was trivially easy to remove the tint with a razor blade and a
hair blower.

Then I started changing my 16" Enkei RPF1's back to the OEM 17" Racing
Harts. I don't know if this will really raise the car the necessary 1" or
not, but the guy at Mr. Tire said he would pass me if I put on the OEM
wheels. The Mazda guy said he never heard of an non-lowered car failing
inspection, but the fact remains it *is* 1" too low as per the law. Anyway,
on the second wheel the Mcgard spline drive broke. Now waiting for another
one to ship from Goodwin Racing.

Hopefully the Toyota will go smoother.

  #9  
Old October 13th 13, 07:57 AM posted to rec.autos.makers.mazda.miata
[email protected]
external usenet poster
 
Posts: 1
Default Failed MD inspection

On Friday, October 26, 2012 10:34:25 AM UTC-4, Frank Berger wrote:
> 1. Rear window is tinted - that's against MD law. Have to have the tint
>
> removed.
>
> 2. Car is too low. I assume (hope) putting pack the 17" wheels will make
>
> it legal.
>
> 3. Right tail light is missing. Not burned out, housing is missing. Never
>
> noticed that.
>
>
>
> Grrr.


Go through with the top down? lol
  #10  
Old October 25th 13, 02:08 PM posted to rec.autos.makers.mazda.miata
Ron
external usenet poster
 
Posts: 58
Default Failed MD inspection

On 10/27/2012 2:17 AM, charlie wrote:
> On 10/27/2012 1:57 AM, charlie wrote:
>> On 10/26/2012 10:34 AM, Frank Berger wrote:
>>> 1. Rear window is tinted - that's against MD law. Have to have the
>>> tint removed.
>>> 2. Car is too low. I assume (hope) putting pack the 17" wheels will
>>> make it legal.
>>> 3. Right tail light is missing. Not burned out, housing is missing.
>>> Never noticed that.
>>>
>>> Grrr.

>>
>> In Georgia, the rear window tint will often result in a ticket.
>> The tail light bit is understandable.
>> Ride height too low? I haven't heard of that one!
>> We've got a bunch of red necks/swamp rats that jack pickups up several
>> feet, beyond what I always thought was allowable, and I've not heard of
>> that causing tickets.
>>
>> The state I grew up in, Illinois, used to have a law that the license
>> plates had to be a minimum distance from the ground. The front plate on
>> a Miata passed if the stock mount was used, and might not if it was
>> moved down from the mouth.
>>
>> How can the housing be missing? What attaches the tail light lens to the
>> body?

>
>
> You can remove the tint yourself if you have something that creates
> steam. Warm/to hot very moist air starts the process, and makes removal
> much easier. Dish washing soap and water, with something like Windex, or
> a very small amount of ammonia added to the dish washing solution also
> helps, and should be repeatedly sprayed on the film. Patience is the
> word. Don't scrape any heating grid elements. Generally, you would get a
> corner of the film to lift, then spray the warm/solution on followed by
> steam, then, after a bit, gently pull on the corner until you feel a
> change. Spray some more solution on, add more steam, wait, and as the
> film loosens, gently pull again. Once the film is off, there may be some
> of the glue remaining. The same process can be used to remove it. You
> can also score the film with a razor blade to help the solution/steam
> penetrate, but it's easy to scratch the glass or the heat grid elements.
>
> If you have a plastic window, test the solution on a small unimportant
> area first. Ammonia can cause problems with some plastics and fabrics.
> With the plastic windows, and high heat areas like Texas, some plastic
> films can
> be a real problem to remove, and cause window replacement to be necessary.



I've never heard of anyone tinting a plastic backglass....and I have
never even tried to tint one. With that said, the easiest way to get the
film off is to park the car in the sun. The hotter the glass gets the
better. Spray the inside of the glass with ammonia then place a black
garbage bag to the inside of the glass and smooth it out as much as
possible by hand. Leave the bag on for about 20 minutes. Remove the bag
and starting in a corner peel the film off. If done correctly it should
come off in one piece. Clean up remaining residue with ammonia, paper
towels, and single edge razors being careful not to nick the heating
elements if equipped with a rear window defogger. Depending on how long
the tint has been on, just peeling off the tint can ruin the defogger
heating elements anyway.

Here's a video on how it's done.

You can ignore most of part one all he is doing is cutting the bag so
it will fit the glass perfectly. Skip up to the 3:20 mark.

http://www.youtube.com/watch?v=Vxu516xRPs8

Part two shows how it's done.

http://www.youtube.com/watch?v=sJAhpgs7b4g


 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Failed NJ Inspection for Emissions BluJeanBaby1130 Dodge 2 February 3rd 07 09:37 PM
My 4L SOHC set codes & failed state inspection DIY'er Ford Explorer 1 June 11th 05 06:12 AM
Failed inspection Rick Corvette 9 April 11th 05 05:18 PM
HELP! failed emission inspection with high HC ppm Robert Technology 5 March 31st 05 02:53 AM
Failed Inspection - 90 Vette Empty3 Corvette 48 October 24th 04 03:10 AM


All times are GMT +1. The time now is 04:28 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.