If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
97 codes need fix
p0404
p0301 p1133 what is the fix I need to do? also this is a SL1 |
Ads |
#2
|
|||
|
|||
P0404 = EGR Circuit (Closed valve Fault)
P0301 = Engine Misfire Detected in Cylinder 1 P1133 = Oxygen Sensor (Too few switches) When was the vehicle last tuned? How many miles? Did it just start acting up or has the service engine soon light been on for some time? If it just started, was any work done to it recently? I'd start with the basics since they are cheap: (1) New properly gapped 0.40" OEM spark plugs, (2) New ignition wires if these are more than a couple years old (make sure they are routed properly), and 3) a good fuel injector cleaner (e.g. Techron). If this does not fix it, I'd take a look at the ignition coil tower. This can be easily removed (4 bolts) and then the connectors can be cleaned with a wire brush and some sandpaper. Make sure the engine block under the base, the base plate, and the bolt holes are also clean and shiny since they provide ground for the unit. (These can have a lot of corrosion preventing good spark and possibly causing the misfire on cylinder #1.) If you still have a problem, you can then try popping the fuel injectors at the connector and making sure they are all clean and tight. I've personally seen simply reseating a fuel injector connector solve a misfire on this engine. If still no luck, then you might try to remove and clean the EGR valve. The gasket is cheap and should be replaced when you do this. As a last resort or if the P1133 code remains, you can try to replace the O2 sensor. Good Luck! Bob "Joe Cawley" > wrote in message ... > p0404 > p0301 > p1133 > > what is the fix I need to do? also this is a SL1 > |
#3
|
|||
|
|||
Note: gap on plugs should be 0.040" Sorry about the typo...
> I'd start with the basics since they are cheap: (1) New properly gapped > 0.40" OEM spark plugs, (2) New ignition wires if these are more than a > couple years old (make sure they are routed properly), and 3) a good fuel > injector cleaner (e.g. Techron). |
#4
|
|||
|
|||
thanks for the info
the car has 172,000 miles light has been on for a long time need to fix for inspection I did replace o2 sensor upper one fixed the light a little on and off now steady again will let you know how I make out "Bob Shuman" > wrote in message ... > Note: gap on plugs should be 0.040" Sorry about the typo... > >> I'd start with the basics since they are cheap: (1) New properly gapped >> 0.40" OEM spark plugs, (2) New ignition wires if these are more than a >> couple years old (make sure they are routed properly), and 3) a good fuel >> injector cleaner (e.g. Techron). > > |
#5
|
|||
|
|||
The mileage helps, but you do not indicate when the plugs were last replaced
or the wires. My guess is that you will also definitely need to remove and at the minimum clean (worst case replace) the EGR valve. As background, my son's '96 Saturn 1.9L had 115K miles when the EGR failed. When I removed it it was pretty coked up in the passageway and was definitely sticking. I used a small flat blade screwdriver to chip most of the stuff out and then used a small dermal tool with a wire brush attachment to polish up inside there as best I could. When I was done I used some throttle body cleaner to dissolve whatever else might have been in there. When I was done I cleaned the passage ways to the intake and exhaust manifolds with a small "battery" type wire brush (for cleaning inside the battery clamp). The EGR valve operated manually beautifully when I was done and everything was pretty clean. The new gasket cost us about $3 and when we put it all back together it worked fine and the code (different from yours, but my guess is your EGR is so bad it won't operate at all any more) disappeared. My point here is the EGR is pretty simple to remove and may be reusable. He has subsequently driven the car for about 1 1/2 years without this re-occurring. My last thought here is if it has not been done lately, replace the PCV valve since these have a tendency to clog and can cause oil burning which can cause spark plug fouling and accelerate the EGR problem. Good luck. Most everything I've suggested here is low cost and easy to do yourself. Bob PS The fuel and air filters are other things which should be changed regularly. The air filter is a breeze to change, but the fuel filter can be difficult due to its location. "Joe Cawley" > wrote in message ... > thanks for the info > > the car has 172,000 miles light has been on for a long time need to fix for > inspection I did replace o2 sensor upper one fixed the light a little on and > off now steady again will let you know how I make out > "Bob Shuman" > wrote in message > ... > > Note: gap on plugs should be 0.040" Sorry about the typo... > > > >> I'd start with the basics since they are cheap: (1) New properly gapped > >> 0.40" OEM spark plugs, (2) New ignition wires if these are more than a > >> couple years old (make sure they are routed properly), and 3) a good fuel > >> injector cleaner (e.g. Techron). > > > > > > |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Codes 19, 26 & 32 on '95 SC2 | Bill | Saturn | 0 | February 27th 05 06:05 PM |
OT - OBD2 Trouble Codes | Jeff Strickland | Jeep | 1 | December 29th 04 06:28 AM |
codes | Sammy | Audi | 6 | November 17th 04 01:16 PM |
Tranny Trouble codes | jonnymcfly | Saturn | 4 | July 7th 04 01:41 AM |