A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » Alfa Romeo
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Help me diagnose this splutter...



 
 
Thread Tools Display Modes
  #11  
Old January 21st 11, 07:46 PM posted to alt.autos.alfa-romeo
Zathras
external usenet poster
 
Posts: 742
Default Help me diagnose this splutter...

On Fri, 21 Jan 2011 14:46:11 -0000, "GT" > wrote:

>If the 'brain' can't sense how much
>air is flowing, then how can it manage fuel/air mixes properly?


Best guess/drop back to default values/limp home mode.

I'm not sure how dissing one would help with the diagnosis though.
Unless there is a fault code, swapping out with a known good one seems
the only reliable way to tell unless you've got specialist MAF test
kit..if such a thing is available.

--
Z
Scotland
Alfa Romeo 156 2.4JTD Veloce Leather (sold)
'Oil' be seeing you..
(Email must have the word 'Alfa' in the
subject line to get through auto-filtering)
Ads
  #12  
Old January 22nd 11, 11:07 PM posted to alt.autos.alfa-romeo
TonyB
external usenet poster
 
Posts: 67
Default Help me diagnose this splutter...


"Dave Savage" > wrote in message
...
>
> "GT" > wrote >
>> Reading around a little and there a few suggestions online that its safe
>> to unplug the MAF and try the car without it. That doesn't seem right to
>> me - sensors are there for a reason, surely? If the 'brain' can't sense
>> how much air is flowing, then how can it manage fuel/air mixes properly?
>>

>
> No doubt someone will be along shortly to offer the technical explanation,
> but I've seen it said many times : "disconnect the MAF and see what effect
> this has". Apparently this does no harm (obviously you eventually need to
> re-connect the old / replacement MAF).
>
> Dave S... :>))


A voltage is passed through the wire which causes it to heat up. As you
try to go faster the air flow increases and the wire cools, changing its
resistance.
This allows the ECU to deliver more fuel. I guess disconnection will simply
increase the fuel flow.

TonyB

  #13  
Old August 10th 11, 10:48 AM posted to alt.autos.alfa-romeo
GT[_14_]
external usenet poster
 
Posts: 150
Default Help me diagnose this splutter...

"Catman" > wrote in message
...
> On 20/01/2011 12:13, GT wrote:
>> 156 2002, 2.0 JTS petrol. I (the car)had a splutter/cough a year or so
>> ago
>> and it eventually went away on its own. Its come back now and I would
>> like
>> to at least figure out what is causing it, if not fix it. The problem:
>>
>> Its independent of gear (done it in 3rd, 4th 5th). I don't tend to rev
>> over
>> about 4000 most of the time as its a nice torquey engine. Problem occurs
>> under load, usually at around 2000 revs. It is repeatable - the 270
>> degree
>> slip road onto the M8 at the top of Livingston is about a 50mph corner,
>> 5th
>> gear. As I come out of it I speed up to er... 70 (ho humm!) and it will
>> splutter most times there. It also does it in 3rd coming out of the silly
>> little roundabouts they stick along in-town dual carriageway 40mph
>> stretches. Its a cough/splutter, lack of power, followed by 'beep beep'
>> motor control failure - go to dealer. As I feel the splutter starting, if
>> I
>> back off on the accellerator and just speed up more gradually all is
>> well.
>> If I drop a cog and increase the revs, all is fine.
>>
>> I have ruled out dirty fuel as its been through several fill ups.
>> I have rules out engine temperature as it doesn't make any difference.
>> I have ruled out spark plugs and electrics because the revs are low, so
>> the
>> demand is not so much - wouldn't this cause problems at higher revs when
>> there are more sparks per minute?

>
> *maybe*


I got a cable and diag software. I found 2 fault codes: P0300 - "Misfires
detected (generic) and P0303 - "Cylinder 3 ifnition failures".

"The emissions Monitoring system has detected misfires, an Air/Fuel micture
problem or other indicators of emissions exceeding the permissible level.
Check the plugs, ignition and fuel systems, and the ending mechanical
condition, and that the oild level is not too high, or oil change overdue.
Defects contribute also to O2 sensor degradeation and premature catalytic
converter efficiency loss.

The reason for this fault is that the EDU has received very high signal from
the sensor. The fault is not is not detected now, but it is stored in
memory. Clear fault codes, and observe for future appearance of the same
fault. Dashboard warning light was activated for this fault."

Sounds like the spark plug or wiring is failing on cylinder 3. I checked out
the throttle sensor and whatever I did to the pedal, the software reported a
valid position - I couldn't get the graph to flicker or jump at all.

Any thoughts to add?

So: My handbrake cable has snapped, cylinder 3 is knackered, the exhaust has
shed its outer skin and can't have long left, the air-con gave up the ghost
last year, I've spotted a few bubbles in the paint round the edges.
Otherwise, all is good in alfa land!

>> I have rules out air flow for the same reason - the engine isn't getting
>> through as much air as when the revs are higher.
>>
>> This (in my mind) leaves the knocc sensor, or something else.
>>
>> Any ideas / suggestions?
>>

>
> Is it drive by wire? If so, I'd bet on the throttle pot.
> Failing that I'd be giving the AFM a stern look.



  #14  
Old August 10th 11, 12:50 PM posted to alt.autos.alfa-romeo
Zathras
external usenet poster
 
Posts: 742
Default Help me diagnose this splutter...

On Wed, 10 Aug 2011 10:48:39 +0100, "GT" > wrote:

>the air-con gave up the ghost last year,


My compressor was grumbling rather loudly when mine got sold at just
over 8 year old.

>I've spotted a few bubbles in the paint round the edges.


I had that too..I wasn't hugely impressed by it either. Also, bubbling
under unmarked paintwork away from edges and many seams slowly growing
cancerous lumps. My local Indy owner (who seems to specialise in old
cheap rubbish) ridiculed me over it!

--
Z
Scotland
Alfa Romeo 156 2.4JTD Veloce Leather (sold)
'Oil' be seeing you..
(Email must have the word 'Alfa' in the
subject line to get through auto-filtering)
  #15  
Old August 10th 11, 01:27 PM posted to alt.autos.alfa-romeo
Catman
external usenet poster
 
Posts: 146
Default Help me diagnose this splutter...

On 10/08/2011 10:48, GT wrote:
> > wrote in message
> ...
>> On 20/01/2011 12:13, GT wrote:
>>> 156 2002, 2.0 JTS petrol. I (the car)had a splutter/cough a year or so
>>> ago
>>> and it eventually went away on its own. Its come back now and I would
>>> like
>>> to at least figure out what is causing it, if not fix it. The problem:
>>>
>>> Its independent of gear (done it in 3rd, 4th 5th). I don't tend to rev
>>> over
>>> about 4000 most of the time as its a nice torquey engine. Problem occurs
>>> under load, usually at around 2000 revs. It is repeatable - the 270
>>> degree
>>> slip road onto the M8 at the top of Livingston is about a 50mph corner,
>>> 5th
>>> gear. As I come out of it I speed up to er... 70 (ho humm!) and it will
>>> splutter most times there. It also does it in 3rd coming out of the silly
>>> little roundabouts they stick along in-town dual carriageway 40mph
>>> stretches. Its a cough/splutter, lack of power, followed by 'beep beep'
>>> motor control failure - go to dealer. As I feel the splutter starting, if
>>> I
>>> back off on the accellerator and just speed up more gradually all is
>>> well.
>>> If I drop a cog and increase the revs, all is fine.
>>>
>>> I have ruled out dirty fuel as its been through several fill ups.
>>> I have rules out engine temperature as it doesn't make any difference.
>>> I have ruled out spark plugs and electrics because the revs are low, so
>>> the
>>> demand is not so much - wouldn't this cause problems at higher revs when
>>> there are more sparks per minute?

>>
>> *maybe*

>
> I got a cable and diag software. I found 2 fault codes: P0300 - "Misfires
> detected (generic) and P0303 - "Cylinder 3 ifnition failures".
>
> "The emissions Monitoring system has detected misfires, an Air/Fuel micture
> problem or other indicators of emissions exceeding the permissible level.
> Check the plugs, ignition and fuel systems, and the ending mechanical
> condition, and that the oild level is not too high, or oil change overdue.
> Defects contribute also to O2 sensor degradeation and premature catalytic
> converter efficiency loss.
>
> The reason for this fault is that the EDU has received very high signal from
> the sensor. The fault is not is not detected now, but it is stored in
> memory. Clear fault codes, and observe for future appearance of the same
> fault. Dashboard warning light was activated for this fault."
>
> Sounds like the spark plug or wiring is failing on cylinder 3. I checked out
> the throttle sensor and whatever I did to the pedal, the software reported a
> valid position - I couldn't get the graph to flicker or jump at all.
>


<fires up babel fish>

That's a bit bloody useless really, isn't it.

'You've got a misfire, mate' is really what it boils down to.

Having said that, if it's flagging emissions exceeding the permisable
level, would it be reasonable to assume that it's because the fuel / air
is not igniting. If there was no fuel, then surely you'd get no
emissions and then no excessive emissions?

That being the case, I'd look at the plugs and such, but....


> Any thoughts to add?
>
> So: My handbrake cable has snapped, cylinder 3 is knackered, the exhaust has
> shed its outer skin and can't have long left, the air-con gave up the ghost
> last year, I've spotted a few bubbles in the paint round the edges.
> Otherwise, all is good in alfa land!


Super. It's probably hit money pit land, I'm afraid.



--
Catman MIB#14 SKoGA#6 TEAR#4 BOTAFOF#38 Apostle#21 COSOC#3
Tyger, Tyger Burning Bright (Remove rust to reply)
116 Giulietta 3.0l Sprint 1.7 147 TS GT 3.2 V6
Triumph Sprint ST 1050: It's blue, see.
#www.cuore-sportivo.co.uk
  #16  
Old August 10th 11, 02:44 PM posted to alt.autos.alfa-romeo
Dave Savage[_3_]
external usenet poster
 
Posts: 62
Default Help me diagnose this splutter...


"Zathras" > wrote in message
news
> On Wed, 10 Aug 2011 10:48:39 +0100, "GT" > wrote:
>
>>the air-con gave up the ghost last year,

>
> My compressor was grumbling rather loudly when mine got sold at just
> over 8 year old.
>


My air con is decidedly feeble (not cold enuf) despite re-gassing earlier
this year (by Kwik Fit so I hae me doots re the quality of the job). I'm
not a fridge engineer / factory-trained Alfa mechanic (it's rumoured these
exist), so ..... if the compressor (whatever that is) is unwell, how much
are we talking to get it fixed / replaced ?

Excuse my mechanical ignorance, I'm just the driver.

Dave S... (waiting to see if the riots extend to Surrey tonight)


>>I've spotted a few bubbles in the paint round the edges.

>
> I had that too..I wasn't hugely impressed by it either. Also, bubbling
> under unmarked paintwork away from edges and many seams slowly growing
> cancerous lumps. My local Indy owner (who seems to specialise in old
> cheap rubbish) ridiculed me over it!
>
> --
> Z
> Scotland
> Alfa Romeo 156 2.4JTD Veloce Leather (sold)
> 'Oil' be seeing you..
> (Email must have the word 'Alfa' in the
> subject line to get through auto-filtering)



  #17  
Old August 10th 11, 11:33 PM posted to alt.autos.alfa-romeo
GT[_14_]
external usenet poster
 
Posts: 150
Default Help me diagnose this splutter...

"Catman" > wrote in message
...
> On 10/08/2011 10:48, GT wrote:
>> > wrote in message
>> ...
>>> On 20/01/2011 12:13, GT wrote:
>>>> 156 2002, 2.0 JTS petrol. I (the car)had a splutter/cough a year or so
>>>> ago
>>>> and it eventually went away on its own. Its come back now and I would
>>>> like
>>>> to at least figure out what is causing it, if not fix it. The problem:
>>>>
>>>> Its independent of gear (done it in 3rd, 4th 5th). I don't tend to rev
>>>> over
>>>> about 4000 most of the time as its a nice torquey engine. Problem
>>>> occurs
>>>> under load, usually at around 2000 revs. It is repeatable - the 270
>>>> degree
>>>> slip road onto the M8 at the top of Livingston is about a 50mph corner,
>>>> 5th
>>>> gear. As I come out of it I speed up to er... 70 (ho humm!) and it will
>>>> splutter most times there. It also does it in 3rd coming out of the
>>>> silly
>>>> little roundabouts they stick along in-town dual carriageway 40mph
>>>> stretches. Its a cough/splutter, lack of power, followed by 'beep beep'
>>>> motor control failure - go to dealer. As I feel the splutter starting,
>>>> if
>>>> I
>>>> back off on the accellerator and just speed up more gradually all is
>>>> well.
>>>> If I drop a cog and increase the revs, all is fine.
>>>>
>>>> I have ruled out dirty fuel as its been through several fill ups.
>>>> I have rules out engine temperature as it doesn't make any difference.
>>>> I have ruled out spark plugs and electrics because the revs are low, so
>>>> the
>>>> demand is not so much - wouldn't this cause problems at higher revs
>>>> when
>>>> there are more sparks per minute?
>>>
>>> *maybe*

>>
>> I got a cable and diag software. I found 2 fault codes: P0300 - "Misfires
>> detected (generic) and P0303 - "Cylinder 3 ifnition failures".
>>
>> "The emissions Monitoring system has detected misfires, an Air/Fuel
>> micture
>> problem or other indicators of emissions exceeding the permissible level.
>> Check the plugs, ignition and fuel systems, and the ending mechanical
>> condition, and that the oild level is not too high, or oil change
>> overdue.
>> Defects contribute also to O2 sensor degradeation and premature catalytic
>> converter efficiency loss.
>>
>> The reason for this fault is that the EDU has received very high signal
>> from
>> the sensor. The fault is not is not detected now, but it is stored in
>> memory. Clear fault codes, and observe for future appearance of the same
>> fault. Dashboard warning light was activated for this fault."
>>
>> Sounds like the spark plug or wiring is failing on cylinder 3. I checked
>> out
>> the throttle sensor and whatever I did to the pedal, the software
>> reported a
>> valid position - I couldn't get the graph to flicker or jump at all.
>>

>
> <fires up babel fish>
>
> That's a bit bloody useless really, isn't it.
>
> 'You've got a misfire, mate' is really what it boils down to.
>
> Having said that, if it's flagging emissions exceeding the permisable
> level, would it be reasonable to assume that it's because the fuel / air
> is not igniting. If there was no fuel, then surely you'd get no emissions
> and then no excessive emissions?
>
> That being the case, I'd look at the plugs and such, but....
>
>
>> Any thoughts to add?
>>
>> So: My handbrake cable has snapped, cylinder 3 is knackered, the exhaust
>> has
>> shed its outer skin and can't have long left, the air-con gave up the
>> ghost
>> last year, I've spotted a few bubbles in the paint round the edges.
>> Otherwise, all is good in alfa land!

>
> Super. It's probably hit money pit land, I'm afraid.


Yes. Another 700 miles and I'll hit the magic 100,000. I'm despirate to
reach it on the original exhaust. It would be nice if all the cylinders were
still going too!! Its been misfiring like this for a few years, gradually
getting worse, but its not a major problem from a driving point of view. My
money is on something in the spark or even the injector department. If the
injector isn't working properly, perhaps its dumping too much fuel on one
cycle and not enough in the next. Unlikely I suppose..


  #18  
Old August 11th 11, 07:02 AM posted to alt.autos.alfa-romeo
Catman
external usenet poster
 
Posts: 146
Default Help me diagnose this splutter...

On 10/08/2011 23:33, GT wrote:
<snip>
>>
>> Super. It's probably hit money pit land, I'm afraid.

>
> Yes. Another 700 miles and I'll hit the magic 100,000.


Hmm. I've had considerably more out of mine, but maybe I was nicer to
them

>I'm despirate to
> reach it on the original exhaust. It would be nice if all the cylinders were
> still going too!! Its been misfiring like this for a few years, gradually
> getting worse, but its not a major problem from a driving point of view. My
> money is on something in the spark or even the injector department. If the
> injector isn't working properly, perhaps its dumping too much fuel on one
> cycle and not enough in the next. Unlikely I suppose..


Very unlikely IMHO. If it's isolated to one cylinder then it really has
to be spark or something physical, though I'm not sure under what
circumstances valve or rings would not have an effect all the time IYSWIM.


--
Catman MIB#14 SKoGA#6 TEAR#4 BOTAFOF#38 Apostle#21 COSOC#3
Tyger, Tyger Burning Bright (Remove rust to reply)
116 Giulietta 3.0l Sprint 1.7 147 TS GT 3.2 V6
Triumph Sprint ST 1050: It's blue, see.
#www.cuore-sportivo.co.uk
  #19  
Old August 11th 11, 08:51 AM posted to alt.autos.alfa-romeo
R C Nesbit
external usenet poster
 
Posts: 142
Default Help me diagnose this splutter...

Gt spoke:
> I got a cable and diag software. I found 2 fault codes: P0300 - "Misfires
> detected (generic) and P0303 - "Cylinder 3 ifnition failures".


These are the same fault codes we get on Lesley's 147 2.0TS

Code comes on, car is hard to start, rough idle and needs more revs to get
moving.
Clear the code and everything is fine, but error returns very quickly (10 -
15 miles)
This was with the generic software with the cable.
I downloaded the AlfaDiag software and it now also reveals P0141
"O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 2)"

Garage recons it is a burned valve on #2 cylinder

--
Rob Pearson
156 1.9jtd sportwagon (now)
164 V6 Lusso (gone)
147 2.0TS lusso (Hers)


  #20  
Old August 11th 11, 10:27 AM posted to alt.autos.alfa-romeo
Catman
external usenet poster
 
Posts: 146
Default Help me diagnose this splutter...

On 11/08/2011 08:51, R C Nesbit wrote:
> Gt spoke:
>> I got a cable and diag software. I found 2 fault codes: P0300 - "Misfires
>> detected (generic) and P0303 - "Cylinder 3 ifnition failures".

>
> These are the same fault codes we get on Lesley's 147 2.0TS
>
> Code comes on, car is hard to start, rough idle and needs more revs to get
> moving.
> Clear the code and everything is fine, but error returns very quickly (10 -
> 15 miles)
> This was with the generic software with the cable.
> I downloaded the AlfaDiag software and it now also reveals P0141
> "O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 2)"
>


Is this the lambda sensor? I thought it only had one.

> Garage recons it is a burned valve on #2 cylinder
>


Wasn't that the same garage that confused the cylinders on their
compression test, though?


--
Catman MIB#14 SKoGA#6 TEAR#4 BOTAFOF#38 Apostle#21 COSOC#3
Tyger, Tyger Burning Bright (Remove rust to reply)
116 Giulietta 3.0l Sprint 1.7 147 TS GT 3.2 V6
Triumph Sprint ST 1050: It's blue, see.
#www.cuore-sportivo.co.uk
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
diagnose this Ashton Crusher[_2_] Technology 39 April 10th 10 05:15 PM
diagnose this Ashton Crusher[_2_] Ford Explorer 34 April 10th 10 05:15 PM
Volkswagen splutter billberry VW water cooled 0 April 21st 08 07:23 AM
'95 5.0 GT Mustang engine stumble and splutter - Please Help. [email protected] Technology 1 November 29th 05 01:43 AM
Cough, splutter. Suggestions? Doug Main BMW 2 October 18th 04 12:00 AM


All times are GMT +1. The time now is 09:57 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.