If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
HELP: 1993 Saturn SL1 Window Regulator - READ THIS!!!
Ok Saturn guru's... I'm hoping someone can help out with this weird thing.
I have a 1993 Saturn SL1 (4dr/Manual). The driver's side window regulator went, so I went to Saturn to buy the part and have a local mechanic install it. I bought the part and brought it to the mechanic. He said that the part didn't fit properly. He said that it was short about an inch and a half. Ok, so I called Saturn and had them double check the part number -- Yep! It's the "right" part. Well, I brought it to the Saturn dealer and had them install it. A few hours later, I was brought to the counter and explained that the part was, indeed, too short. The old regulator's channel was 15 1/2 inches, yet the "new" OEM part was 14 1/4 inches. Therefore, the window wouldn't roll up all the way. The Saturn mechanics called other dealerships to have them check their inventory -- they all were 14 1/4 inches. Saturn told me that they called the engineers and the corporate office to inform them of this and so far have had no response. I was given a rental, but was told it needed to be returned tomorrow even if my car wasn't fixed (i.e. they'd put it back together and call me when they found something). I don't care about the rental car, but I've never heard of this! My local Saturn told me that manufacturers were different and the parts must have been made to different specs, but they have no idea why they'd be this short. So, my question is, what do I do now? I haven't looked into junk yards yet to see if there's a part I can grab from something else, but am I just out of luck? I thought that Saturn had their stuff together. Other than this, the car is decent, so I'm not junking it just because of that. Any ideas on where to find a proper regulator to fit this? Thanks in advance -- remove the "NOSPAM" in my name to reply: duckie74 at yahoo dot com |
Ads |
#2
|
|||
|
|||
"B. Case" > wrote in message ... > Ok Saturn guru's... I'm hoping someone can help out with this weird thing. > > I have a 1993 Saturn SL1 (4dr/Manual). The driver's side window regulator > went, so I went to Saturn to buy the part and have a local mechanic install > it. I bought the part and brought it to the mechanic. He said that the > part didn't fit properly. He said that it was short about an inch and a > half. Ok, so I called Saturn and had them double check the part number -- > Yep! It's the "right" part. > > Well, I brought it to the Saturn dealer and had them install it. A few > hours later, I was brought to the counter and explained that the part was, > indeed, too short. The old regulator's channel was 15 1/2 inches, yet the > "new" OEM part was 14 1/4 inches. Therefore, the window wouldn't roll up > all the way. The Saturn mechanics called other dealerships to have them > check their inventory -- they all were 14 1/4 inches. > > Saturn told me that they called the engineers and the corporate office to > inform them of this and so far have had no response. I was given a rental, > but was told it needed to be returned tomorrow even if my car wasn't fixed > (i.e. they'd put it back together and call me when they found something). > > I don't care about the rental car, but I've never heard of this! My local > Saturn told me that manufacturers were different and the parts must have > been made to different specs, but they have no idea why they'd be this > short. > > So, my question is, what do I do now? I haven't looked into junk yards yet > to see if there's a part I can grab from something else, but am I just out > of luck? I thought that Saturn had their stuff together. Other than this, > the car is decent, so I'm not junking it just because of that. > > Any ideas on where to find a proper regulator to fit this? > > Thanks in advance -- remove the "NOSPAM" in my name to reply: duckie74 at > yahoo dot com > > > And you think that is funny, I went to the dealer for a Idler Pulley and tensioner and the parts were bigger than what we took off. The parts guy went in the back and found one of the older ones and he measurer the diameter of the wheel and it was indeed larger on the newer part then on the old. He said to buy a bigger belt. The mechanic told him he was an idiot. There are I am sure other parts that were changed in the car but the manufacturer should have the like or same part on hand. Can you imagine a short staff window? Elector |
#3
|
|||
|
|||
Replaced one on a 1991 SL2 about two years ago. Bought the part from
a Salvage Yard for $45. Took about 4 hours to repair. Most of the time spent was trying to drill out the "spin rivits" used to hold the regulator in place. Today I just finished replacing the regulator on my wife's 1993 SC1 (coupe) 192,000 miles. This time I bought the part NEW from Saturn. It cost $97. The part for the SC is different from the regulator used by the sedan (SL). This time I only spent 3 hours on the repair, because I had learned how to quickly drill the "spin rivits" out! Also, had to use a BLUE TIP WRENCH for a few seconds to break the seal on the screw on disks used to hold the window glass to regulator bracket. The SATURN OEM PART fit perfectly !!! The regulator repair is alot of work, and I do not recommend that a "beginning" repair person try this. It takes some skill. "B. Case" > wrote in message m>... > Ok Saturn guru's... I'm hoping someone can help out with this weird thing. > > I have a 1993 Saturn SL1 (4dr/Manual). The driver's side window regulator > went, so I went to Saturn to buy the part and have a local mechanic install > it. I bought the part and brought it to the mechanic. He said that the > part didn't fit properly. He said that it was short about an inch and a > half. Ok, so I called Saturn and had them double check the part number -- > Yep! It's the "right" part. > > Well, I brought it to the Saturn dealer and had them install it. A few > hours later, I was brought to the counter and explained that the part was, > indeed, too short. The old regulator's channel was 15 1/2 inches, yet the > "new" OEM part was 14 1/4 inches. Therefore, the window wouldn't roll up > all the way. The Saturn mechanics called other dealerships to have them > check their inventory -- they all were 14 1/4 inches. > > Saturn told me that they called the engineers and the corporate office to > inform them of this and so far have had no response. I was given a rental, > but was told it needed to be returned tomorrow even if my car wasn't fixed > (i.e. they'd put it back together and call me when they found something). > > I don't care about the rental car, but I've never heard of this! My local > Saturn told me that manufacturers were different and the parts must have > been made to different specs, but they have no idea why they'd be this > short. > > So, my question is, what do I do now? I haven't looked into junk yards yet > to see if there's a part I can grab from something else, but am I just out > of luck? I thought that Saturn had their stuff together. Other than this, > the car is decent, so I'm not junking it just because of that. > > Any ideas on where to find a proper regulator to fit this? > > Thanks in advance -- remove the "NOSPAM" in my name to reply: duckie74 at > yahoo dot com |
#4
|
|||
|
|||
Hi Paul,
Yep. I definitely didn't do this by myself -- no mechanical skill whatsoever. So far, Saturn still hasn't heard back from their engineers as to what the problem is with the part being manufactured too short. I think I was able to locate a junk yard part, so I'm keeping my fingers crossed. Thanks for the reply! "paul" > wrote in message m... > Replaced one on a 1991 SL2 about two years ago. Bought the part from > a Salvage Yard for $45. Took about 4 hours to repair. Most of the > time spent was trying to drill out the "spin rivits" used to hold the > regulator in place. > > Today I just finished replacing the regulator on my wife's 1993 SC1 > (coupe) 192,000 miles. This time I bought the part NEW from Saturn. > It cost $97. The part for the SC is different from the regulator used > by the sedan (SL). This time I only spent 3 hours on the repair, > because I had learned how to quickly drill the "spin rivits" out! > Also, had to use a BLUE TIP WRENCH for a few seconds to break the seal > on the screw on disks used to hold the window glass to regulator > bracket. The SATURN OEM PART fit perfectly !!! > > The regulator repair is alot of work, and I do not recommend that a > "beginning" repair person try this. It takes some skill. > > "B. Case" > wrote in message m>... > > Ok Saturn guru's... I'm hoping someone can help out with this weird thing. > > > > I have a 1993 Saturn SL1 (4dr/Manual). The driver's side window regulator > > went, so I went to Saturn to buy the part and have a local mechanic install > > it. I bought the part and brought it to the mechanic. He said that the > > part didn't fit properly. He said that it was short about an inch and a > > half. Ok, so I called Saturn and had them double check the part number -- > > Yep! It's the "right" part. > > > > Well, I brought it to the Saturn dealer and had them install it. A few > > hours later, I was brought to the counter and explained that the part was, > > indeed, too short. The old regulator's channel was 15 1/2 inches, yet the > > "new" OEM part was 14 1/4 inches. Therefore, the window wouldn't roll up > > all the way. The Saturn mechanics called other dealerships to have them > > check their inventory -- they all were 14 1/4 inches. > > > > Saturn told me that they called the engineers and the corporate office to > > inform them of this and so far have had no response. I was given a rental, > > but was told it needed to be returned tomorrow even if my car wasn't fixed > > (i.e. they'd put it back together and call me when they found something). > > > > I don't care about the rental car, but I've never heard of this! My local > > Saturn told me that manufacturers were different and the parts must have > > been made to different specs, but they have no idea why they'd be this > > short. > > > > So, my question is, what do I do now? I haven't looked into junk yards yet > > to see if there's a part I can grab from something else, but am I just out > > of luck? I thought that Saturn had their stuff together. Other than this, > > the car is decent, so I'm not junking it just because of that. > > > > Any ideas on where to find a proper regulator to fit this? > > > > Thanks in advance -- remove the "NOSPAM" in my name to reply: duckie74 at > > yahoo dot com |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
1994 Accord LX Power Window Problem | R. P. | Honda | 6 | December 28th 04 02:09 AM |
window clacking noise on 2004 E60 530i | Oliver Hui | BMW | 0 | October 25th 04 03:25 AM |
Passenger side front window | bill | Audi | 4 | August 25th 04 07:27 AM |
HELP: 1993 SL1 Window Regulator - READ THIS!! | B. Case | Saturn | 0 | May 12th 04 09:32 PM |
Saturn Lemons- epidemic flaws, engine cracks, ball joints | misterfact | Antique cars | 0 | January 6th 04 06:04 PM |