A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » Corvette
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Loose rearview mirror on C6



 
 
Thread Tools Display Modes
  #1  
Old December 13th 12, 07:51 PM posted to alt.autos.corvette
Ron Stewart
external usenet poster
 
Posts: 16
Default Loose rearview mirror on C6

I just had the windshield replaced on my 2005 C6 and now the mirror is loose
and and wobbles up and down going over even small bumps. The guy that did
the work did a beautiful job on the windshield but I'm not sure about his
knowledge on this problem. There is lots of discussion on the Corvette forum
about this same problem. Can any one here add some helpful tips? Dad?
Thanks,
Ron Stewart Santa Rosa, Ca

Ads
  #2  
Old December 13th 12, 08:44 PM posted to alt.autos.corvette
Dad[_2_]
external usenet poster
 
Posts: 52
Default Loose rearview mirror on C6

You're screwed. The window man leaned and/on or rotated the mirror while
pushing down on it and sheared out the die casting's snap ring groove. It
can be fixed by removing it and recutting the groove a bit wider/deeper and
using a bigger snap ring. Big hassle and may still lead to a new mirror. The
last C5 I did was not worth the effort (she hit the garage door while
backing out) as it doesn't have enough metal to use 2 snap rings and a wave
washer that was require. Had to epoxy the top snap ring in to keep it solid.

Window service owes you a mirror.

By the way the other C5 had it folded back and forth ever time it was put
in/out of the garage for over 2 years.

"Ron Stewart" > wrote in message
...
>I just had the windshield replaced on my 2005 C6 and now the mirror is
>loose and and wobbles up and down going over even small bumps. The guy
>that did the work did a beautiful job on the windshield but I'm not sure
>about his knowledge on this problem. There is lots of discussion on the
>Corvette forum about this same problem. Can any one here add some helpful
>tips? Dad?
> Thanks,
> Ron Stewart Santa Rosa, Ca



  #3  
Old December 14th 12, 01:35 AM posted to alt.autos.corvette
Unquestionably Confused
external usenet poster
 
Posts: 44
Default Loose rearview mirror on C6

Dad,

Are you reading something more into Ron's post? From his description of
the problem I take that he's talking about the REAR view mirror mounted
to the windshield, rather than the side view mirror which is what you
seem to be talking about.

Sounds like Ron's problem is that the mirror assembly isn't snugged
tight to the metal button fastened to the glass. Ron? How about
fabricating a plastic shim of some sort to snug it up if you can't get
it tight with the hex head screw?




On 12/13/2012 1:44 PM, Dad wrote:
> You're screwed. The window man leaned and/on or rotated the mirror while
> pushing down on it and sheared out the die casting's snap ring groove. It
> can be fixed by removing it and recutting the groove a bit wider/deeper and
> using a bigger snap ring. Big hassle and may still lead to a new mirror. The
> last C5 I did was not worth the effort (she hit the garage door while
> backing out) as it doesn't have enough metal to use 2 snap rings and a wave
> washer that was require. Had to epoxy the top snap ring in to keep it solid.
>
> Window service owes you a mirror.
>
> By the way the other C5 had it folded back and forth ever time it was put
> in/out of the garage for over 2 years.
>
> "Ron Stewart" > wrote in message
> ...
>> I just had the windshield replaced on my 2005 C6 and now the mirror is
>> loose and and wobbles up and down going over even small bumps. The guy
>> that did the work did a beautiful job on the windshield but I'm not sure
>> about his knowledge on this problem. There is lots of discussion on the
>> Corvette forum about this same problem. Can any one here add some helpful
>> tips? Dad?
>> Thanks,
>> Ron Stewart Santa Rosa, Ca

>
>


  #4  
Old December 14th 12, 04:06 AM posted to alt.autos.corvette
Dad[_2_]
external usenet poster
 
Posts: 52
Default Loose rearview mirror on C6

Good catch. If it is the inside mirror it has no set screw. To seat it pull
parallel to the windshield towards the dash and rock it back and forth until
you hear a click. Removal is done in the reverse and it can be a bad clip
since it is removed by doing the rock back and forth while pulling up in the
same incline as the windshield. There is more than one warning about NOT
pulling towards the back.

Thanks for the heads up Confused, I was relating to the whining on CF about
the poor C5 mirrors and I haven't been back there in years so they could
have been talking about the inside mirror and I wouldn't have seen it.


"Unquestionably Confused" > wrote in message
...
> Dad,
>
> Are you reading something more into Ron's post? From his description of
> the problem I take that he's talking about the REAR view mirror mounted to
> the windshield, rather than the side view mirror which is what you seem to
> be talking about.
>
> Sounds like Ron's problem is that the mirror assembly isn't snugged tight
> to the metal button fastened to the glass. Ron? How about fabricating a
> plastic shim of some sort to snug it up if you can't get it tight with the
> hex head screw?
>
>
>
>
> On 12/13/2012 1:44 PM, Dad wrote:
>> You're screwed. The window man leaned and/on or rotated the mirror while
>> pushing down on it and sheared out the die casting's snap ring groove. It
>> can be fixed by removing it and recutting the groove a bit wider/deeper
>> and
>> using a bigger snap ring. Big hassle and may still lead to a new mirror.
>> The
>> last C5 I did was not worth the effort (she hit the garage door while
>> backing out) as it doesn't have enough metal to use 2 snap rings and a
>> wave
>> washer that was require. Had to epoxy the top snap ring in to keep it
>> solid.
>>
>> Window service owes you a mirror.
>>
>> By the way the other C5 had it folded back and forth ever time it was put
>> in/out of the garage for over 2 years.
>>
>> "Ron Stewart" > wrote in message
>> ...
>>> I just had the windshield replaced on my 2005 C6 and now the mirror is
>>> loose and and wobbles up and down going over even small bumps. The guy
>>> that did the work did a beautiful job on the windshield but I'm not sure
>>> about his knowledge on this problem. There is lots of discussion on the
>>> Corvette forum about this same problem. Can any one here add some
>>> helpful
>>> tips? Dad?
>>> Thanks,
>>> Ron Stewart Santa Rosa, Ca

>>
>>

>



  #5  
Old December 14th 12, 09:59 PM posted to alt.autos.corvette
Ron Stewart
external usenet poster
 
Posts: 16
Default Loose rearview mirror on C6

Good news!
I drove out to the shop that installed the windshield and showed him the
loose mirror. He took it off the windshield, took into his shop and took it
apart, took out the bent pins and straightend them. Put it all back together
and back onto it's mount on the glass. Now it is stable and just fine. He
told me he has had similar problems with this on Volvos, who use a similar
design. I told him about one of the guys on the forum who makes new pins out
of 7/64"dia. drill shanks. He said he would keep that in mind.
I'm guessing the soft metal pins might be needed for safety reasons to meet
government crash requirements to ensure the mirror breaks before it breaks
someone's head.
Thanks for the quick response to my post.
Ron
"Unquestionably Confused" > wrote in message
...
> Dad,
>
> Are you reading something more into Ron's post? From his description of
> the problem I take that he's talking about the REAR view mirror mounted to
> the windshield, rather than the side view mirror which is what you seem to
> be talking about.
>
> Sounds like Ron's problem is that the mirror assembly isn't snugged tight
> to the metal button fastened to the glass. Ron? How about fabricating a
> plastic shim of some sort to snug it up if you can't get it tight with the
> hex head screw?
>
>
>
>
> On 12/13/2012 1:44 PM, Dad wrote:
>> You're screwed. The window man leaned and/on or rotated the mirror while
>> pushing down on it and sheared out the die casting's snap ring groove. It
>> can be fixed by removing it and recutting the groove a bit wider/deeper
>> and
>> using a bigger snap ring. Big hassle and may still lead to a new mirror.
>> The
>> last C5 I did was not worth the effort (she hit the garage door while
>> backing out) as it doesn't have enough metal to use 2 snap rings and a
>> wave
>> washer that was require. Had to epoxy the top snap ring in to keep it
>> solid.
>>
>> Window service owes you a mirror.
>>
>> By the way the other C5 had it folded back and forth ever time it was put
>> in/out of the garage for over 2 years.
>>
>> "Ron Stewart" > wrote in message
>> ...
>>> I just had the windshield replaced on my 2005 C6 and now the mirror is
>>> loose and and wobbles up and down going over even small bumps. The guy
>>> that did the work did a beautiful job on the windshield but I'm not sure
>>> about his knowledge on this problem. There is lots of discussion on the
>>> Corvette forum about this same problem. Can any one here add some
>>> helpful
>>> tips? Dad?
>>> Thanks,
>>> Ron Stewart Santa Rosa, Ca

>>
>>

>


  #6  
Old December 14th 12, 10:04 PM posted to alt.autos.corvette
Ron Stewart
external usenet poster
 
Posts: 16
Default Loose rearview mirror on C6

That should be 5/64" not 7/64".
Ron
"Ron Stewart" > wrote in message
...
> Good news!
> I drove out to the shop that installed the windshield and showed him the
> loose mirror. He took it off the windshield, took into his shop and took
> it apart, took out the bent pins and straightend them. Put it all back
> together and back onto it's mount on the glass. Now it is stable and just
> fine. He told me he has had similar problems with this on Volvos, who use
> a similar design. I told him about one of the guys on the forum who makes
> new pins out of 7/64"dia. drill shanks. He said he would keep that in
> mind.
> I'm guessing the soft metal pins might be needed for safety reasons to
> meet government crash requirements to ensure the mirror breaks before it
> breaks someone's head.
> Thanks for the quick response to my post.
> Ron
> "Unquestionably Confused" > wrote in message
> ...
>> Dad,
>>
>> Are you reading something more into Ron's post? From his description of
>> the problem I take that he's talking about the REAR view mirror mounted
>> to the windshield, rather than the side view mirror which is what you
>> seem to be talking about.
>>
>> Sounds like Ron's problem is that the mirror assembly isn't snugged tight
>> to the metal button fastened to the glass. Ron? How about fabricating a
>> plastic shim of some sort to snug it up if you can't get it tight with
>> the hex head screw?
>>
>>
>>
>>
>> On 12/13/2012 1:44 PM, Dad wrote:
>>> You're screwed. The window man leaned and/on or rotated the mirror while
>>> pushing down on it and sheared out the die casting's snap ring groove.
>>> It
>>> can be fixed by removing it and recutting the groove a bit wider/deeper
>>> and
>>> using a bigger snap ring. Big hassle and may still lead to a new mirror.
>>> The
>>> last C5 I did was not worth the effort (she hit the garage door while
>>> backing out) as it doesn't have enough metal to use 2 snap rings and a
>>> wave
>>> washer that was require. Had to epoxy the top snap ring in to keep it
>>> solid.
>>>
>>> Window service owes you a mirror.
>>>
>>> By the way the other C5 had it folded back and forth ever time it was
>>> put
>>> in/out of the garage for over 2 years.
>>>
>>> "Ron Stewart" > wrote in message
>>> ...
>>>> I just had the windshield replaced on my 2005 C6 and now the mirror is
>>>> loose and and wobbles up and down going over even small bumps. The guy
>>>> that did the work did a beautiful job on the windshield but I'm not
>>>> sure
>>>> about his knowledge on this problem. There is lots of discussion on the
>>>> Corvette forum about this same problem. Can any one here add some
>>>> helpful
>>>> tips? Dad?
>>>> Thanks,
>>>> Ron Stewart Santa Rosa, Ca
>>>
>>>

>>

>


  #7  
Old December 14th 12, 10:56 PM posted to alt.autos.corvette
Unquestionably Confused
external usenet poster
 
Posts: 44
Default Loose rearview mirror on C6

On 12/14/2012 2:59 PM, Ron Stewart wrote:
> Good news!
> I drove out to the shop that installed the windshield and showed him the
> loose mirror. He took it off the windshield, took into his shop and took
> it apart, took out the bent pins and straightend them. Put it all back
> together and back onto it's mount on the glass. Now it is stable and
> just fine. He told me he has had similar problems with this on Volvos,
> who use a similar design. I told him about one of the guys on the forum
> who makes new pins out of 7/64"dia. drill shanks. He said he would keep
> that in mind.
> I'm guessing the soft metal pins might be needed for safety reasons to
> meet government crash requirements to ensure the mirror breaks before it
> breaks someone's head.


That's our government. Brilliance in considering the plight of the
center seat passengers in our Corvettes<g>


> Thanks for the quick response to my post.


Glad to hear that it all worked out. I based my answer on my
experiences with the C4 and C5 (I think I tightened the mirror mount on
the C5 - not sure)

Learned something new from Dad (and you) about the C6. If I ever get
one, I'll...




  #8  
Old December 15th 12, 12:24 AM posted to alt.autos.corvette
Dad[_2_]
external usenet poster
 
Posts: 52
Default Loose rearview mirror on C6


"Unquestionably Confused" > wrote in message
...
> On 12/14/2012 2:59 PM, Ron Stewart wrote:
>> Good news!
>> I drove out to the shop that installed the windshield and showed him the
>> loose mirror. He took it off the windshield, took into his shop and took
>> it apart, took out the bent pins and straightend them. Put it all back
>> together and back onto it's mount on the glass. Now it is stable and
>> just fine. He told me he has had similar problems with this on Volvos,
>> who use a similar design. I told him about one of the guys on the forum
>> who makes new pins out of 7/64"dia. drill shanks. He said he would keep
>> that in mind.
>> I'm guessing the soft metal pins might be needed for safety reasons to
>> meet government crash requirements to ensure the mirror breaks before it
>> breaks someone's head.

>
> That's our government. Brilliance in considering the plight of the center
> seat passengers in our Corvettes<g>
>
>
>> Thanks for the quick response to my post.

>
> Glad to hear that it all worked out. I based my answer on my experiences
> with the C4 and C5 (I think I tightened the mirror mount on the C5 - not
> sure)
>
> Learned something new from Dad (and you) about the C6. If I ever get one,
> I'll...
>

WOW, metal pins in a car made in the USA, whoda thunk it? The way the manual
reads I expected it to be a plastic detent of some sort.

I changed windshields/glass back in the late 50s/60s while going to college
and there are just gobs of things that can go wrong. A guy that had a
Fingerhut in Toledo started doing mobile changes like they all do now. What
a learning experience, it got to where we were not allowed to touch a dirty
or wet car because you couldn't see if there was any other damage and they
would come back on us to fix it. The one that really ripped my boss was a
small piece of locating masking tape was left on a windshield and they made
us drive back out and pull it off. Ahhh the good old days.

For your continued learning experiance for both the C5 & the C6 here's a
list of things which a lot of people don't know, whether or not they're in
the manual, copied from one or more of the Corvette groups.

-The C6 has front and rear brake cooling ducts beneath the car. They use
high pressure areas to bring air to the low pressure areas where the brakes
are.

-The button between the "1" and "2" buttons on the door is for easy
exit/entry.

-The doors have a manual release located near the floor.

-The C6 can be entered by using the provided key in the lock above the rear
license plate.

-The C6 can be started by placing the fob in the hidden receptacle in the
glove box.

-The Automatic transmission has programming to hold gears while cornering.

-To get the dash to dim, you need to hold the dimmer switch in when rotated!
The book does not tell you to push it in prior to rotation for the dimming.

-To get the garage door opener programmed when you have a variable code
opener like Sears sells, you need to press the learn button on the unit then
push the opener button in the C6 3 times for 2 seconds and it picks up the
code. The book does not state that however if you go to the web site it will
tell you how to address this problem.

-The holes on the inside surface of the exhaust tips are to eliminate
high-RPM hiss.

-Turn the light switch one notch up from "auto" and then release to turn off
the DRLs.

-Moving the turn signal lever part way and then releasing it will cause the
lights to blink three times. This is for lane changes.

-To fully turn off traction control, you must press the button twice.

-If your window does not roll up or down that little bit at the top
(indexing) then it may need to be set. This is explained in the user's
manual, but involves holding the window down for 5 seconds using the switch
and then holding it all the way to the top for 5 seconds using the switch.
-Condition/Concern:

Some customers may state that the clock reads in 24 hour time (military
time) on vehicles equipped with the RPO US8 or US9 radios.

Recommendation/Instructions:

If the customer wishes to switch between military time and the 12 hour
clock., please follow the following procedu

Press and hold the hours button for 2-3 seconds.

Turn the radio tuner knob left or right to toggle between military time and
regular time. Turn the tuner knob to the desired setting and let go of knob
for 30 seconds for the change to occur.

Note: The Navigation radio (RPO U3U) can be changed from military time to
regular time by accessing the clock menu.

This list is for the C5 secrets:
1. The little yellow "helper light" on the bottom of the rear-view mirror
that illuminates the shifter area.
2. That you can put your key in the driver's door and turn it twice towards
the front to unlock the passenger door and a third time to pop the trunk.
3. That you can pop the trunk and also pop the gas cap cover by pulling on
metal lines hidden in the back.
4. That the little slotted cover on the dash behind the steering wheel is
where the inside air temperature sensor is located.
5. All of the option codes are in the glove box. And if they aren't there,
look on the underside of the rear compartment lid (passenger side, I think).
6. Tire inflation recommended pressures are on the driver's door (don't
laugh, this comes up a lot).
7. The thing that looks like a little LED near the DIC buttons is a light
sensor.
8. The thing that looks like a little LED near the defroster vent is a UV
sensor for determining A/C usage to compensate for the heating effect of the
sun.
9. Your build sheet is in the front re-bar, your front bumper cover must be
pulled for access!
10. When the engine is shut off, you can get the odometer reading by turning
on the parking lights.
11. You can program setting #3 (both memory buttons at once) in the seat
memory to run the seat back and steering wheel forward for getting in/out of
the car with the engine running.
12. Reset oil life by pumping gas pedal 3 times (but not with the engine
running).
13. Hold down RESET button while on one of the trip odometers and it gives
you the mileage you traveled since last starting the car.
14. Hold down the Active Handling button for 5 sec. to engage "Competitive
Driving" (2000 and previous years must be stopped.)
15. If you hate DRLs you can pull the e-brake ONE click and they go off....
16. Simply remove fuse #2 under the hood and your DRLs will be out
permanently. Only thing affected is that when you unlock at night using the
key fob your front turn signal lights and back up lights will not flash. You
front turn signals will operate normally. GO STEALTH and extend the life of
your front turn signal bulbs (changing them out is not picnic).
17. The side-view mirrors can twist both forward and backward, decreasing
the chance of damage if struck.
18. If you pull the seatbelts all the way out while you're buckled in, they
ratchet back in to hold you tighter into the seat (that's how the owner's
video describes this feature)
19. The parking brake is self-adjusting... but depends on the car rolling or
wanting to roll backward to work. Not mentioned in the owners manual (looked
for it).
20. I didn't realize there is a red LED light on the left side of the radio
so I had one installed to work when the security system is on. Someone told
me to program the radio theft lock feature and that initiated the LED
flashing. Now I have two of them flashing when the security system is on.
21. There is a release opening with a flap to let air out of the car when
the hatch is closed.
It is located just above the driver side rear compartment, behind the panel.
22. There is a spot on the driver side just out of the middle compartment
under the carpet for the lug nut key. You should have a compartment on the
drivers & passenger's side (in the trunk) and a center compartment. On the
left (drivers) side of the center compartment, on the left side where the
center cover fits, there is an 'indent' that holds the wheel lock key.
23. The bolts that hold the disk changer in the car, when installed from the
factory cannot be removed. They have to be cut off.
24. You can ground your amp to a screw/bolt that holds the rear middle
compartment to the frame.
25. If you turn on the headlights, then go to parking light position
quickly, the lamps remain up but the headlights are not burning - this is
for washing the lights.
26. If you have a 6-speed car you can pop the trunk when the car is running
by lifting the e-brake.
27. On my Z06, the interior illumination light (the light that shines down
from the rear-view mirror) is blue-ish and it will turn to a yellow color by
sliding a colored lens over the lamp opening (no sheezot!) - I am not sure
why this happens but the light does illuminate the console/shifter area.
28. Also not listed here, but the good CorvetteForum folks schooled me on
this - if you go to comp-mode on the DIC, you can just hit reset to go back
to displaying whatever mode you were in (fuel, odom etc.) and the comp-mode
will still be activated.
29. If you have the passive entry featu If you lock your keys in the car,
wait a few minutes and then shake the car. That will unlock the car.
30. HUD has a shift light for manuals.
31. You can easily shift the M6 trans up or down without the clutch if you
match revs. (Not great for longevity, however.)
32. You can eject the CD from the in-dash player without turning on any
power. Don't even need key in the ignition.
33. The cruise will disengage if you purposely make sharp side to side turns
while cruising at say 60-80 mph.
34. When the engine is shut off, you can get the odometer reading by turning
on the parking lights.
35. HUD has a shift light for A4's too... it comes on during a WOT run just
before it shifts!
36. With the engine off, opening the glovebox automatically turns on
interior lighting.
37. You have 20 minutes of auxillary power after shutting the car off.
38. There a key combination that can get the DIC to show any codes the car
has thrown without autotap, etc. That combination is as follows:
.. Turn the ignition key to the ON position, but do not start the car.
.. Clear any pre-set messages by pressing the RESET button.
.. Hold the OPTIONS button down, and press the FUEL button 4 times. This will
get you into the CODES section of the DIC. The computer will automatically
display all the codes your car has created. It will cycle through each code
every 3 seconds. Any code that ends in H is a code that was registered
previously but is no longer an issue.
.. Once the computer has finished going through all of it's codes, press
RESET to enter Manual Configuration mode. It should start with a module and
show "NO CODES" or "# CODES".
.. To optionally reset the codes once in manual mode, press and hold RESET
until it displays "NO CODES".
.. Press OPTIONS button to go to the next module.


  #9  
Old December 15th 12, 01:45 AM posted to alt.autos.corvette
Rufus
external usenet poster
 
Posts: 57
Default Loose rearview mirror on C6

Dad wrote:
> "Unquestionably Confused" > wrote in message
> ...
>> On 12/14/2012 2:59 PM, Ron Stewart wrote:
>>> Good news!
>>> I drove out to the shop that installed the windshield and showed him the
>>> loose mirror. He took it off the windshield, took into his shop and took
>>> it apart, took out the bent pins and straightend them. Put it all back
>>> together and back onto it's mount on the glass. Now it is stable and
>>> just fine. He told me he has had similar problems with this on Volvos,
>>> who use a similar design. I told him about one of the guys on the forum
>>> who makes new pins out of 7/64"dia. drill shanks. He said he would keep
>>> that in mind.
>>> I'm guessing the soft metal pins might be needed for safety reasons to
>>> meet government crash requirements to ensure the mirror breaks before it
>>> breaks someone's head.

>>
>> That's our government. Brilliance in considering the plight of the center
>> seat passengers in our Corvettes<g>
>>
>>
>>> Thanks for the quick response to my post.

>>
>> Glad to hear that it all worked out. I based my answer on my experiences
>> with the C4 and C5 (I think I tightened the mirror mount on the C5 - not
>> sure)
>>
>> Learned something new from Dad (and you) about the C6. If I ever get one,
>> I'll...
>>

> WOW, metal pins in a car made in the USA, whoda thunk it? The way the manual
> reads I expected it to be a plastic detent of some sort.
>
> I changed windshields/glass back in the late 50s/60s while going to college
> and there are just gobs of things that can go wrong. A guy that had a
> Fingerhut in Toledo started doing mobile changes like they all do now. What
> a learning experience, it got to where we were not allowed to touch a dirty
> or wet car because you couldn't see if there was any other damage and they
> would come back on us to fix it. The one that really ripped my boss was a
> small piece of locating masking tape was left on a windshield and they made
> us drive back out and pull it off. Ahhh the good old days.
>
> For your continued learning experiance for both the C5 & the C6 here's a
> list of things which a lot of people don't know, whether or not they're in
> the manual, copied from one or more of the Corvette groups.
>
> -The C6 has front and rear brake cooling ducts beneath the car. They use
> high pressure areas to bring air to the low pressure areas where the brakes
> are.
>
> -The button between the "1" and "2" buttons on the door is for easy
> exit/entry.
>
> -The doors have a manual release located near the floor.
>
> -The C6 can be entered by using the provided key in the lock above the rear
> license plate.
>
> -The C6 can be started by placing the fob in the hidden receptacle in the
> glove box.
>
> -The Automatic transmission has programming to hold gears while cornering.
>
> -To get the dash to dim, you need to hold the dimmer switch in when rotated!
> The book does not tell you to push it in prior to rotation for the dimming.
>
> -To get the garage door opener programmed when you have a variable code
> opener like Sears sells, you need to press the learn button on the unit then
> push the opener button in the C6 3 times for 2 seconds and it picks up the
> code. The book does not state that however if you go to the web site it will
> tell you how to address this problem.
>
> -The holes on the inside surface of the exhaust tips are to eliminate
> high-RPM hiss.
>
> -Turn the light switch one notch up from "auto" and then release to turn off
> the DRLs.
>
> -Moving the turn signal lever part way and then releasing it will cause the
> lights to blink three times. This is for lane changes.
>
> -To fully turn off traction control, you must press the button twice.
>
> -If your window does not roll up or down that little bit at the top
> (indexing) then it may need to be set. This is explained in the user's
> manual, but involves holding the window down for 5 seconds using the switch
> and then holding it all the way to the top for 5 seconds using the switch.
> -Condition/Concern:
>
> Some customers may state that the clock reads in 24 hour time (military
> time) on vehicles equipped with the RPO US8 or US9 radios.
>
> Recommendation/Instructions:
>
> If the customer wishes to switch between military time and the 12 hour
> clock., please follow the following procedu
>
> Press and hold the hours button for 2-3 seconds.
>
> Turn the radio tuner knob left or right to toggle between military time and
> regular time. Turn the tuner knob to the desired setting and let go of knob
> for 30 seconds for the change to occur.
>
> Note: The Navigation radio (RPO U3U) can be changed from military time to
> regular time by accessing the clock menu.
>
> <snip>


I knew most of these about the C6...especially the one about sticking
the fob in the glove box receptacle - when I got my Z06 I started
reading the owners manual .pdf before I even sent the check and received
the car.

That knowledge served me well when my fob died on me during a trip to
Vegas...the car is a 2008 and even though it only had 4100 miles on it
when I bought it the fob battery was three years old at least. So it
died on me at a gas station...and I had to use a few of these tricks to
get myself to a drug store and buy another fob battery. Now I carry a
spare one in the rear box.

I've since schooled at least one other C6 owner on this one...and the
key slot over the license plate. Now if I could learn to shift a six
speed smoother...

--
- Rufus
  #10  
Old December 15th 12, 04:43 PM posted to alt.autos.corvette
Dad[_2_]
external usenet poster
 
Posts: 52
Default Loose rearview mirror on C6


"Rufus" > wrote in message
news
>> <snip>

>
> I knew most of these about the C6...especially the one about sticking the
> fob in the glove box receptacle - when I got my Z06 I started reading the
> owners manual .pdf before I even sent the check and received the car.
>
> That knowledge served me well when my fob died on me during a trip to
> Vegas...the car is a 2008 and even though it only had 4100 miles on it
> when I bought it the fob battery was three years old at least. So it died
> on me at a gas station...and I had to use a few of these tricks to get
> myself to a drug store and buy another fob battery. Now I carry a spare
> one in the rear box.
>
> I've since schooled at least one other C6 owner on this one...and the key
> slot over the license plate. Now if I could learn to shift a six speed
> smoother...
>
> --
> - Rufus

..
There is one little quirk about the C6 that still catches me and if I
remember right it got me once in the C5. The interior light knob on the
lower left dash can be bumped by your knee and turn the interior lights on.
For some reason they will not time out when turned on there and it has
killed the battery twice. I've not tried to duplicate it yet to ****ed to
have to go through the restarting/charging process when I wanted to be
driving it.


 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
rearview mirror adoom Chrysler 0 July 25th 09 08:31 PM
Rearview Mirror query Pete[_11_] Driving 59 July 25th 07 05:32 AM
Rearview mirror bug '59 VW air cooled 3 February 22nd 07 08:30 AM
Loose Rearview mirror - 97 Eddie Bauer Xx Ford Explorer 1 September 17th 06 10:19 PM
AWA [OFFER] rearview mirror, sun visor, truck mirror, jeep mirror tradegroup[email protected] General 0 November 28th 05 12:55 PM


All times are GMT +1. The time now is 01:11 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright 2004-2018 AutoBanter.
The comments are property of their posters.