If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
2000 MPV Check Engine Light and Exhaust
Mazda MPV 200 130K miles
Check engine light has been on and off without resolution prior to 100K. As early as the first year we have noticed this problem. When on, nothing found. When off, it was not even lighting up momentarily up upon staring the engine. Niether Mazda in each case, nor an independent mechanic could diagnose. Now we have a potential bill for over $3000 for exhaust manifold and CO2 sensor repair. Should the check engine light be on if there is no detectible issue? Has anyone else had this type/ similar issue. |
Ads |
#2
|
|||
|
|||
The Engine check light shows a detectible issue. The obd2 code (when read)
will show what is setting the light. I don't understand the potential bill, it's out of line. 4 wire Bosch O2 sensor from parts house <$100 What is wrong with the manifold? They can be welded (usually), or an aftermarket header used. The entire exhaust system from the engine to the rear is available from aftermarket or used. Stock used parts are also available. You might get more information by going to www.miata.net (including parts sources and information) Common causes are a bad igniton coil or coils, sticking injectors, Plug wires, plugs, etc. "Eric G" > wrote in message oups.com... > Mazda MPV 200 130K miles > > Check engine light has been on and off without resolution prior to > 100K. As early as the first year we have noticed this problem. When > on, nothing found. When off, it was not even lighting up momentarily > up upon staring the engine. > > Niether Mazda in each case, nor an independent mechanic could diagnose. > Now we have a potential bill for over $3000 for exhaust manifold and > CO2 sensor repair. > > Should the check engine light be on if there is no detectible issue? > > Has anyone else had this type/ similar issue. > |
#3
|
|||
|
|||
"Eric G" > wrote in message oups.com... > Mazda MPV 200 130K miles > > Check engine light has been on and off without resolution prior to > 100K. As early as the first year we have noticed this problem. When > on, nothing found. When off, it was not even lighting up momentarily > up upon staring the engine. From this description, one might assume that the light was being driven "on" all the time, but failed to be on all the time due to a poor connection, bad bulb, etc. The bulb check when switching the ignition on is supposed to assure you that the bulb works. > > Niether Mazda in each case, nor an independent mechanic could diagnose. If the OBDII system did not report a failing code, then you have either a faulty computer or no codes to report. I have not heard of any "faulty computer" reports, although I expect it happens. > Now we have a potential bill for over $3000 for exhaust manifold and > CO2 sensor repair. Exhaust manifold? What could possibly be wrong there? Was it cracked? Making noise? An 02 sensor costs about $100 and (guessing here) about $50 to have installed. If the system was not reporting specific codes, why change the O2 sensor? > > Should the check engine light be on if there is no detectible issue? To my knowledge, no. There are other engine codes that can be generated without illuminating the light, but the light should stay off if everything is OK. > > Has anyone else had this type/ similar issue. > |
#4
|
|||
|
|||
ok here is the list that has been wrong with the your mpv, front and rear
exhaust manfiolds crack causin the o2 sensors to fail due to conamination, there is an intake manfiold recall, rear heater pipes underneath vehcile are failing due to corrosion, and there is transmission recalls for the module to be re programmed, also the liftgate dampers in the rear have a recall on them as well. "KWS" > wrote in message ... > > "Eric G" > wrote in message > oups.com... >> Mazda MPV 200 130K miles >> >> Check engine light has been on and off without resolution prior to >> 100K. As early as the first year we have noticed this problem. When >> on, nothing found. > > When off, it was not even lighting up momentarily >> up upon staring the engine. > > From this description, one might assume that the light was being driven > "on" > all the time, but failed to be on all the time due to a poor connection, > bad > bulb, etc. The bulb check when switching the ignition on is supposed to > assure you that the bulb works. > >> >> Niether Mazda in each case, nor an independent mechanic could diagnose. > > If the OBDII system did not report a failing code, then you have either a > faulty computer or no codes to report. I have not heard of any "faulty > computer" reports, although I expect it happens. > >> Now we have a potential bill for over $3000 for exhaust manifold and >> CO2 sensor repair. > > Exhaust manifold? What could possibly be wrong there? Was it cracked? > Making > noise? An 02 sensor costs about $100 and (guessing here) about $50 to > have > installed. If the system was not reporting specific codes, why change the > O2 > sensor? >> >> Should the check engine light be on if there is no detectible issue? > > To my knowledge, no. There are other engine codes that can be generated > without illuminating the light, but the light should stay off if > everything > is OK. >> >> Has anyone else had this type/ similar issue. >> > > |
#5
|
|||
|
|||
Regarding the exhaust manifolds: Here is what I am being told: They
are leaking. No mention of cracks. This resolves itself once they warm up and seal off the leak. (I was told his could be heard and was not discovered based on check engine codes. Actually codes found are listed below.) The inspection docs refer to the "CAT" (catalytic converter) and "Manifolds" leaking. I was told by service that the CAT is part of the exhaust manifolds and the cats alone cannot be changed. The whole manifold needs to be replaced. Does this sound right? So do CATs leak? Manifolds leak? What cause this? Does the above make sense? So are the exhaust manifolds/ cat converters under recall? O2 sensor? Intake Manifold Control Module (aka "IMRC Control" below).? With the list of items they have quoted below what caused what to fail and what can be considered recall issues? Where do I find recall info for the MPV? ____________________ Here are the details from Mazda - Prior history: Bypass Air Control valve resolved at 84K under recall/ warranty. Problem was that engine kept cutting off within a few seconds after starting. I remember an O2 sensor being replaced but this is not documented anywhere. I'll check my records. This is the problem found from my current service invoice. By the way, this was found while I had brought the MPV in to have the power steering repaired. It ends up the pulley came off the pump. They replaced the pulley, nut, installed new drive belt and repaired the spline on power steering pump. This was considered a freak incident. No one at Mazda had ever seen this. Ironically, an independent mechanic I contacted for a second opinion says he just had this issue last week. While performing a routine inspection, after the power steering work, they found this: "Found code P0136 and P1512. Middle O2 [typo? - CO2]+ front and back cat need to be replace due to exhaust leak causing P0136 intake runner control unit need to be replaced for P1512" The service rep told me the CO2 sensor shorted out. All the docs/ invoices refer to O2. I think theses are the same. Here are the parts they quoted: IMRC Control [intake manifold control module] Oxygen Sensor R Manifold L Manifold Exhaust Manifold Gasket I will seek a second opinion before I do any thing. I need to find out what has been recalled. Also, I need to determine if the faulty, malfunctioning check engine light: 1) is now reliable, 2) missed something over the last several months and 3) Could it missing a problem prevented early detection and resolution that has now led to a larger exhaust failure? Another pending question is: "Why could not Mazda resolve the check engine light issue over the last several months and even last year? We had documented engine light malfunctions in Spring 04 and now in 05. |
#6
|
|||
|
|||
"Eric G" > wrote:
>Regarding the exhaust manifolds: Here is what I am being told: They >are leaking. No mention of cracks. This resolves itself once they warm >up and seal off the leak. (I was told his could be heard and was not >discovered based on check engine codes. Actually codes found are >listed below.) > >The inspection docs refer to the "CAT" (catalytic converter) and >"Manifolds" leaking. I was told by service that the CAT is part of >the exhaust manifolds and the cats alone cannot be changed. The whole >manifold needs to be replaced. Does this sound right? > >So do CATs leak? Manifolds leak? What cause this? Does the above >make sense? > >So are the exhaust manifolds/ cat converters under recall? O2 sensor? >Intake Manifold Control Module (aka "IMRC Control" below).? With the >list of items they have quoted below what caused what to fail and what >can be considered recall issues? Where do I find recall info for the >MPV? >____________________ > >Here are the details from Mazda - > >Prior history: Bypass Air Control valve resolved at 84K under recall/ >warranty. Problem was that engine kept cutting off within a few >seconds after starting. I remember an O2 sensor being replaced but >this is not documented anywhere. I'll check my records. > > >This is the problem found from my current service invoice. By the way, >this was found while I had brought the MPV in to have the power >steering repaired. It ends up the pulley came off the pump. They >replaced the pulley, nut, installed new drive belt and repaired the >spline on power steering pump. This was considered a freak incident. >No one at Mazda had ever seen this. Ironically, an independent >mechanic I contacted for a second opinion says he just had this issue >last week. > >While performing a routine inspection, after the power steering work, >they found this: > >"Found code P0136 and P1512. Middle O2 [typo? - CO2]+ front and back >cat need to be replace due to exhaust leak causing P0136 intake runner >control unit need to be replaced for P1512" > >The service rep told me the CO2 sensor shorted out. All the docs/ >invoices refer to O2. I think theses are the same. It is an O2 sensor, not a CO2 sensor. Trying to sense CO2 would not make much sense, CO2 is hard to avoid if you are burning carbon (gas). >Here are the parts they quoted: >IMRC Control [intake manifold control module] >Oxygen Sensor >R Manifold >L Manifold >Exhaust Manifold Gasket > >I will seek a second opinion before I do any thing. I need to find out >what has been recalled. Also, I need to determine if the faulty, >malfunctioning check engine light: 1) is now reliable, 2) missed >something over the last several months and 3) Could it missing a >problem prevented early detection and resolution that has now led to a >larger exhaust failure? > >Another pending question is: "Why could not Mazda resolve the check >engine light issue over the last several months and even last year? We >had documented engine light malfunctions in Spring 04 and now in 05. I would think that if the problem existed and was evident during the warranty period, Mazda should fix it. Not that I am a lawyer. Leon -- Leon van Dommelen Bozo, the White 96 Sebring Miata .) http://www.dommelen.net/miata EXIT THE INTERSTATES (Jamie Jensen) |
#7
|
|||
|
|||
Iv been responding to your question in the newsgroup, give me your VIN
number that way i can enter it into the computer and it will tell me your exhaust setup, now the exhaust manfiolds are prone to cracking at the pipe which is connected to the flange of the manfiold which is connected to the head of the motor, when cracked it will leak exhaust and can be heard upon startup becuase when cold metal shrinks and will expose the crack and it will leak as it warms up it will expand and the crack will be closed and no leak can be heard, but when you visually inspect the actual manfiold you will be able ot see carbon on the outside of the flange and that is where the leaks occur, when you have a cracked manifold vacuum from the exhaust flowing rearwards will draw air from the outside into your exhaust and past your o2 sensors (not co2) which will contaminate the sensors and render them useless now iv seen both manifolds go or one at a time this has no recalls on it unfortuneatly and the customer has to pay. When your oxygen sensor fails it is sending a low/lean signal to the PCM (engine computer) the PCM then starts to dump fuel to compensate for a false lean signal which will result in a drastic fuel mileage reduction and possibly killing the catalyst in the converter(s). Now replacing these manfiolds is a big job and it is not easy especially when oyu snap the studs of in the head now youv got to drill/remove/retap the head while in a cramped space and possibly damging the head in the process which will result in head removal on the customers behalf, I am little skeptical now you said the dealer replaced the o2 sensor previously try and pull up the history and check if they had the same codes then as you do now if you do this should have been covered under warranty and either the mechanic didnt want to do the job becaus eit doesnt pay very well to do it and it is nasty to do or the service manager didnt want to do a warranty claim becuase he doesnt get paid as much to do the job with warranty as he would with the customer. The check engine light is reliable it is there to tell you you have a problem and it never stays on just because it wants to, your best bet is to do the research and see why they replaced that o2 sensor previously i havent seen them go just becuase iv seen them go becaus ethe manifolds were cracked but not just because so go get the history and report back. "Eric G" > wrote in message oups.com... > Mazda MPV 200 130K miles > > Check engine light has been on and off without resolution prior to > 100K. As early as the first year we have noticed this problem. When > on, nothing found. When off, it was not even lighting up momentarily > up upon staring the engine. > > Niether Mazda in each case, nor an independent mechanic could diagnose. > Now we have a potential bill for over $3000 for exhaust manifold and > CO2 sensor repair. > > Should the check engine light be on if there is no detectible issue? > > Has anyone else had this type/ similar issue. > |
#8
|
|||
|
|||
Today i just worked on a 2000 mpv with leaky manifolds but it didnt have
CAT's in the manfiolds 2003 mpv's have cats but the 2000's do not have cats in the manifolds! so you got the wrong quote. and the cats do not need replacement unless you have cat efficiancy codes. "Eric G" > wrote in message oups.com... > Mazda MPV 200 130K miles > > Check engine light has been on and off without resolution prior to > 100K. As early as the first year we have noticed this problem. When > on, nothing found. When off, it was not even lighting up momentarily > up upon staring the engine. > > Niether Mazda in each case, nor an independent mechanic could diagnose. > Now we have a potential bill for over $3000 for exhaust manifold and > CO2 sensor repair. > > Should the check engine light be on if there is no detectible issue? > > Has anyone else had this type/ similar issue. > |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 6 | December 7th 06 04:55 PM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 5 | July 10th 05 05:24 AM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 5 | March 21st 05 05:33 AM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 10 | November 16th 04 05:28 AM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 10 | November 1st 04 05:24 AM |