If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Vag-Com Software Help
Anybody use Vag-Com software often or at all? I bought a KKL USB for my '00 Audi A4 Quattro and I hooked it up and got some fault codes. The thing is it wouldn't let me reset the codes. Is there away to get around paying the couple hundred bucks? Appreciate it.
|
Ads |
#2
|
|||
|
|||
> wrote in message ... > Anybody use Vag-Com software often or at all? I bought a KKL USB for my > '00 Audi A4 Quattro and I hooked it up and got some fault codes. The > thing is it wouldn't let me reset the codes. Is there away to get around > paying the couple hundred bucks? Appreciate it. > What software/version are you using? I bought a KKL on ebay that was supposed to work with Ross-Tech v.311 or v.409, but I it would work only with the earlier version. Haven't resolved the issue with the seller yet, but so far he has been good about responding to me and says he will either replace it or give me a refund. I had no problem clearing the codes though even with the non-registered software. You can't clear individual codes. You have to clear them all for a particular module. I think you need to give more details. If you are clearing them with the car running they may be triggered again so it may only look like you haven't cleared them. |
#3
|
|||
|
|||
Vag-Com Software Help
You should be able to clear codes with the free version of Vag-Com (I
could). Also, for the record since you already have a hardware interface you like, becoming completely registered and having full featured VagCom (with support) is $100. -Arthur P.S. if you still can't get it to work, email me privately and I'll walk you through it. lid wrote: > Anybody use Vag-Com software often or at all? I bought a KKL USB for > my '00 Audi A4 Quattro and I hooked it up and got some fault codes. > The thing is it wouldn't let me reset the codes. Is there away to > get around paying the couple hundred bucks? Appreciate it. > > |
#4
|
|||
|
|||
Vag-Com Software Help
You should be able to clear codes with the free version of Vag-Com (I
could). Also, for the record since you already have a hardware interface you like, becoming completely registered and having full featured VagCom (with support) is $100. -Arthur P.S. if you still can't get it to work, email me privately and I'll walk you through it. lid wrote: > Anybody use Vag-Com software often or at all? I bought a KKL USB for > my '00 Audi A4 Quattro and I hooked it up and got some fault codes. > The thing is it wouldn't let me reset the codes. Is there away to > get around paying the couple hundred bucks? Appreciate it. > > |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Antsoft Best domain software | Vasilisa | Technology | 0 | October 5th 05 05:39 PM |
VAG-COM - CORRECT SOFTWARE AND DRIVERS | RickT | Audi | 3 | September 8th 05 08:02 PM |
OBD-II Software | mick | Alfa Romeo | 11 | November 13th 04 12:57 PM |
BMW CARSOFT DIAGNOSTIC SOFTWARE | BestAutoScientist | BMW | 0 | November 8th 04 08:02 PM |
Earn $500 to $700 per Week Downloading FREE Software | Cash Cow | Antique cars | 0 | August 16th 03 03:39 AM |