If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
any way to protect NOS fenders?
Looks like I just bought myself another car... a '64 Stude convertible,
comes with NOS front fenders. Now fenders on Studes are made in a real retarded manner, there is a vertical brace at the rear edge with a tiny little gap between it and the outer skin. Guess where they all rust? What would you guys do to protect this area and keep it from rusting? Normally in this situation I would strip the factory primer off and brush POR-15 over the inside of the fender, but that's not going to help here - the part that rusts you can't get a brush in. Is there any place that would, say, chemically strip the fender and then dip it in epoxy paint or something really rust resistant? thanks, nate -- replace "fly" with "com" to reply. http://home.comcast.net/~njnagel |
Ads |
#2
|
|||
|
|||
Nate Nagel wrote: > > Looks like I just bought myself another car... a '64 Stude convertible, > comes with NOS front fenders. Now fenders on Studes are made in a real > retarded manner, there is a vertical brace at the rear edge with a tiny > little gap between it and the outer skin. Guess where they all rust? > > What would you guys do to protect this area and keep it from rusting? > Normally in this situation I would strip the factory primer off and > brush POR-15 over the inside of the fender, but that's not going to help > here - the part that rusts you can't get a brush in. Is there any place > that would, say, chemically strip the fender and then dip it in epoxy > paint or something really rust resistant? > > thanks, > > nate > > I fill the gaps with foundation coating. That stuff never gets hard. Needless to day, you ain't gonna drive that thang in the ice 'n snow, right? -- JT Just tooling through cyberspace in my ancient G4 |
#3
|
|||
|
|||
Grumpy au Contraire wrote:
> > Nate Nagel wrote: > >>Looks like I just bought myself another car... a '64 Stude convertible, >>comes with NOS front fenders. Now fenders on Studes are made in a real >>retarded manner, there is a vertical brace at the rear edge with a tiny >>little gap between it and the outer skin. Guess where they all rust? >> >>What would you guys do to protect this area and keep it from rusting? >>Normally in this situation I would strip the factory primer off and >>brush POR-15 over the inside of the fender, but that's not going to help >>here - the part that rusts you can't get a brush in. Is there any place >>that would, say, chemically strip the fender and then dip it in epoxy >>paint or something really rust resistant? >> >>thanks, >> >>nate >> >> > > > > I fill the gaps with foundation coating. That stuff never gets hard. > > Needless to day, you ain't gonna drive that thang in the ice 'n snow, right? > > when you say fill in the gaps you mean like seal off that whole area behind the brace? Do you leave the hole at the bottom open? nate -- replace "fly" with "com" to reply. http://home.comcast.net/~njnagel |
#4
|
|||
|
|||
Nate Nagel wrote: > > Grumpy au Contraire wrote: > > > > > Nate Nagel wrote: > > > >>Looks like I just bought myself another car... a '64 Stude convertible, > >>comes with NOS front fenders. Now fenders on Studes are made in a real > >>retarded manner, there is a vertical brace at the rear edge with a tiny > >>little gap between it and the outer skin. Guess where they all rust? > >> > >>What would you guys do to protect this area and keep it from rusting? > >>Normally in this situation I would strip the factory primer off and > >>brush POR-15 over the inside of the fender, but that's not going to help > >>here - the part that rusts you can't get a brush in. Is there any place > >>that would, say, chemically strip the fender and then dip it in epoxy > >>paint or something really rust resistant? > >> > >>thanks, > >> > >>nate > >> > >> > > > > > > > > I fill the gaps with foundation coating. That stuff never gets hard. > > > > Needless to day, you ain't gonna drive that thang in the ice 'n snow, right? > > > > > > when you say fill in the gaps you mean like seal off that whole area > behind the brace? Do you leave the hole at the bottom open? > > nate > > I ain't answering until you answer question #2... <G> -- JT Just tooling through cyberspace in my ancient G4 |
#5
|
|||
|
|||
Grumpy au Contraire wrote:
> > Nate Nagel wrote: > >>Grumpy au Contraire wrote: >> >> >>>Nate Nagel wrote: >>> >>> >>>>Looks like I just bought myself another car... a '64 Stude convertible, >>>>comes with NOS front fenders. Now fenders on Studes are made in a real >>>>retarded manner, there is a vertical brace at the rear edge with a tiny >>>>little gap between it and the outer skin. Guess where they all rust? >>>> >>>>What would you guys do to protect this area and keep it from rusting? >>>>Normally in this situation I would strip the factory primer off and >>>>brush POR-15 over the inside of the fender, but that's not going to help >>>>here - the part that rusts you can't get a brush in. Is there any place >>>>that would, say, chemically strip the fender and then dip it in epoxy >>>>paint or something really rust resistant? >>>> >>>>thanks, >>>> >>>>nate >>>> >>>> >>> >>> >>> >>>I fill the gaps with foundation coating. That stuff never gets hard. >>> >>>Needless to day, you ain't gonna drive that thang in the ice 'n snow, right? >>> >>> >> >>when you say fill in the gaps you mean like seal off that whole area >>behind the brace? Do you leave the hole at the bottom open? >> >>nate >> >> > > > > I ain't answering until you answer question #2... > > <G> > Well, we don't *get* what I consider snow here, so I guess the answer is "no, unless I move" <G> nate -- replace "fly" with "com" to reply. http://home.comcast.net/~njnagel |
#6
|
|||
|
|||
Nate Nagel wrote: > > Grumpy au Contraire wrote: > > > > > Nate Nagel wrote: > > > >>Grumpy au Contraire wrote: > >> > >> > >>>Nate Nagel wrote: > >>> > >>> > >>>>Looks like I just bought myself another car... a '64 Stude convertible, > >>>>comes with NOS front fenders. Now fenders on Studes are made in a real > >>>>retarded manner, there is a vertical brace at the rear edge with a tiny > >>>>little gap between it and the outer skin. Guess where they all rust? > >>>> > >>>>What would you guys do to protect this area and keep it from rusting? > >>>>Normally in this situation I would strip the factory primer off and > >>>>brush POR-15 over the inside of the fender, but that's not going to help > >>>>here - the part that rusts you can't get a brush in. Is there any place > >>>>that would, say, chemically strip the fender and then dip it in epoxy > >>>>paint or something really rust resistant? > >>>> > >>>>thanks, > >>>> > >>>>nate > >>>> > >>>> > >>> > >>> > >>> > >>>I fill the gaps with foundation coating. That stuff never gets hard. > >>> > >>>Needless to day, you ain't gonna drive that thang in the ice 'n snow, right? > >>> > >>> > >> > >>when you say fill in the gaps you mean like seal off that whole area > >>behind the brace? Do you leave the hole at the bottom open? > >> > >>nate > >> > >> > > > > > > > > I ain't answering until you answer question #2... > > > > <G> > > > > Well, we don't *get* what I consider snow here, so I guess the answer is > "no, unless I move" <G> > > nate > You live too close to DeeCee and are obviously getting some coachin' from the evil liberal that you sometimes hang with thus are sharpening your issue avoidance skills... Yes? <G> -- JT Just tooling through cyberspace in my ancient G4 |
#7
|
|||
|
|||
Robin Banks wrote: > > On Mon, 18 Oct 2004 18:02:16 -0400, Nate Nagel > wrote: > > > Well, we don't *get* what I consider snow here > > I hate you. ;-) > > It's SO close to being put away time here. Temps have been in the 40s/low > 50s, we had frost warnings... <sigh> I'll probably have both cars under wraps > by next week. Already got the winterizing treatments for everything. > > I hate that it'll be until late April 'till I see my babies rolling again. > > ~~R.Banks Don't let him fool you. He lives in MD and depending of how nasty the winter decides to be, a substantial amount of snow, ice, slush, and of course salt infects the roads from November to April. Now, here in Austin, Texas, one can generally drive vintage tin daily year round. That's why I'm bustin' his chops! <G> JT 1931 Studebaker President State Coupe (Q4) 1955 Studebaker President State Coupe - Future Project 1955 Studebaker President State Sedan - Almost done Daily Driver 1956 Studebaker Power Hawk - Long Time Fun Car - (Will be burial container) 1964 Studebaker Champ P/U T-6 Long Bed - Daily driver 1983 Honda FE - My answer to increasing gas prices 1956 Leica M2 |
#8
|
|||
|
|||
Grumpy au Contraire wrote:
> > Robin Banks wrote: > >>On Mon, 18 Oct 2004 18:02:16 -0400, Nate Nagel > wrote: >> >> >>>Well, we don't *get* what I consider snow here >> >>I hate you. ;-) >> >>It's SO close to being put away time here. Temps have been in the 40s/low >>50s, we had frost warnings... <sigh> I'll probably have both cars under wraps >>by next week. Already got the winterizing treatments for everything. >> >>I hate that it'll be until late April 'till I see my babies rolling again. >> >>~~R.Banks > > > > > Don't let him fool you. He lives in MD and depending of how nasty the > winter decides to be, a substantial amount of snow, ice, slush, and of > course salt infects the roads from November to April. > I would disagree with the "substantial amount." Generally it only snows to any significant degree a couple days a year. However, having the road crews dump craploads of salt on the road as a pre-emptive measure when it's only going to snow enough to tint things white - and melt off anyway as soon as the sun comes out - is a distinct possibility > Now, here in Austin, Texas, one can generally drive vintage tin daily > year round. > > That's why I'm bustin' his chops! > > <G> You're a braver man than I, I drove my '62 to work one day when it was about 95 degrees out, I think I lost 20 lbs. in about 30 miles I like air conditioning, it's a Good Thing. (I didn't choose to drive it that day, my other car was in the shop that day for some necessary timing belt maintenance. The *NEXT* time I drove it to work I got caught in a torrential downpour, with those dinky little windshield wipers and a defroster I never hooked up. I think Mother Nature likes laughing at people, because it was the middle of summer.) nate -- replace "fly" with "com" to reply. http://home.comcast.net/~njnagel |
#9
|
|||
|
|||
Grumpy au Contraire wrote:
> > Nate Nagel wrote: > >>Grumpy au Contraire wrote: >> >> >>>Nate Nagel wrote: >>> >>> >>>>Grumpy au Contraire wrote: >>>> >>>> >>>> >>>>>Nate Nagel wrote: >>>>> >>>>> >>>>> >>>>>>Looks like I just bought myself another car... a '64 Stude convertible, >>>>>>comes with NOS front fenders. Now fenders on Studes are made in a real >>>>>>retarded manner, there is a vertical brace at the rear edge with a tiny >>>>>>little gap between it and the outer skin. Guess where they all rust? >>>>>> >>>>>>What would you guys do to protect this area and keep it from rusting? >>>>>>Normally in this situation I would strip the factory primer off and >>>>>>brush POR-15 over the inside of the fender, but that's not going to help >>>>>>here - the part that rusts you can't get a brush in. Is there any place >>>>>>that would, say, chemically strip the fender and then dip it in epoxy >>>>>>paint or something really rust resistant? >>>>>> >>>>>>thanks, >>>>>> >>>>>>nate >>>>>> >>>>>> >>>>> >>>>> >>>>> >>>>>I fill the gaps with foundation coating. That stuff never gets hard. >>>>> >>>>>Needless to day, you ain't gonna drive that thang in the ice 'n snow, right? >>>>> >>>>> >>>> >>>>when you say fill in the gaps you mean like seal off that whole area >>>>behind the brace? Do you leave the hole at the bottom open? >>>> >>>>nate >>>> >>>> >>> >>> >>> >>>I ain't answering until you answer question #2... >>> >>><G> >>> >>Well, we don't *get* what I consider snow here, so I guess the answer is >>"no, unless I move" <G> >> >>nate >> > > > > You live too close to DeeCee and are obviously getting some coachin' > from the evil liberal that you sometimes hang with thus are sharpening > your issue avoidance skills... Yes? > > <G> > maybe <G> seriously, any car I put together needs to be a practical driver, as I don't actually own a car newer than 1988 and that one does need occasional attention (getting better, though, now that I've had it a while.) I don't plan on driving in bad weather but you never know. nate -- replace "fly" with "com" to reply. http://home.comcast.net/~njnagel |
#10
|
|||
|
|||
Nate Nagel wrote: > > Grumpy au Contraire wrote: > > > > > Nate Nagel wrote: > > > >>Grumpy au Contraire wrote: > >> > >> > >>>Nate Nagel wrote: > >>> > >>> > >>>>Grumpy au Contraire wrote: > >>>> > >>>> > >>>> > >>>>>Nate Nagel wrote: > >>>>> > >>>>> > >>>>> > >>>>>>Looks like I just bought myself another car... a '64 Stude convertible, > >>>>>>comes with NOS front fenders. Now fenders on Studes are made in a real > >>>>>>retarded manner, there is a vertical brace at the rear edge with a tiny > >>>>>>little gap between it and the outer skin. Guess where they all rust? > >>>>>> > >>>>>>What would you guys do to protect this area and keep it from rusting? > >>>>>>Normally in this situation I would strip the factory primer off and > >>>>>>brush POR-15 over the inside of the fender, but that's not going to help > >>>>>>here - the part that rusts you can't get a brush in. Is there any place > >>>>>>that would, say, chemically strip the fender and then dip it in epoxy > >>>>>>paint or something really rust resistant? > >>>>>> > >>>>>>thanks, > >>>>>> > >>>>>>nate > >>>>>> > >>>>>> > >>>>> > >>>>> > >>>>> > >>>>>I fill the gaps with foundation coating. That stuff never gets hard. > >>>>> > >>>>>Needless to day, you ain't gonna drive that thang in the ice 'n snow, right? > >>>>> > >>>>> > >>>> > >>>>when you say fill in the gaps you mean like seal off that whole area > >>>>behind the brace? Do you leave the hole at the bottom open? > >>>> > >>>>nate > >>>> > >>>> > >>> > >>> > >>> > >>>I ain't answering until you answer question #2... > >>> > >>><G> > >>> > >>Well, we don't *get* what I consider snow here, so I guess the answer is > >>"no, unless I move" <G> > >> > >>nate > >> > > > > > > > > You live too close to DeeCee and are obviously getting some coachin' > > from the evil liberal that you sometimes hang with thus are sharpening > > your issue avoidance skills... Yes? > > > > <G> > > > > maybe <G> > > seriously, any car I put together needs to be a practical driver, as I > don't actually own a car newer than 1988 and that one does need > occasional attention (getting better, though, now that I've had it a > while.) I don't plan on driving in bad weather but you never know. > > nate > > Okay, okay... Youse worn me down! What I do is stand the fender on the back edge, use masking tape to prevent the foundation sealant from running all over the place and fill the entire area with the stuff. Let it dry for about a month (preferably in JP's garage this time of year) Don't forget to use epoxy primer and a top coat before the foundation coating though.. The reason that it has to dry is that it doesn't particularly like undercoating. It will take several attempts to undercoat those areas but when done, it should last a very long time depending on how much you abuse it but your wouldn't do anything like that, right? -- JT Just tooling through cyberspace in my ancient G4 |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
protect your car's engine | Waltervw | Audi | 3 | November 30th 04 01:53 AM |
protect your car's engine | Waltervw | BMW | 1 | November 24th 04 04:14 PM |
protect your car's engine | Waltervw | Alfa Romeo | 0 | November 23rd 04 03:00 PM |
mystery fenders | Glenn Pavlovic | Antique cars | 1 | October 29th 04 07:44 AM |
20's-30's fenders | Glenn Pavlovic | Antique cars | 1 | October 29th 03 01:59 AM |