If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Anyone replace the muffler on their Chrysler 300m? What did you use?
I've been looking into various brands (Walker, Magnaflow, Flowmaster,
etc) and can't really find anything made with stainless steel that matches the dimensions of the factory OEM muffler. The 300m has a muffler AND a resonator under the rear of the car. The tail-pipe comes out the resonator (which looks like a muffler but apparently isin't). The original muffler shell measures 18" long, 12" wide and 6" high (oval profile). I can find some aftermarket stainless mufflers that are 18" long, but their oval profile seems to be quite a bit smaller (5" by 8" for example). For non-stainless types (aluminized) the Walker 21375 seems to be a good match - but I'd rather replace it with another stainless steel one if I can find it. Any ideas? Comments? |
Ads |
#2
|
|||
|
|||
Anyone replace the muffler on their Chrysler 300m? What did you use?
On Sat, 08 Dec 2012 15:45:57 -0500, MoPar Man > wrote:
>I've been looking into various brands (Walker, Magnaflow, Flowmaster, >etc) and can't really find anything made with stainless steel that >matches the dimensions of the factory OEM muffler. > >The 300m has a muffler AND a resonator under the rear of the car. The >tail-pipe comes out the resonator (which looks like a muffler but >apparently isin't). > >The original muffler shell measures 18" long, 12" wide and 6" high (oval >profile). > >I can find some aftermarket stainless mufflers that are 18" long, but >their oval profile seems to be quite a bit smaller (5" by 8" for >example). > >For non-stainless types (aluminized) the Walker 21375 seems to be a good >match - but I'd rather replace it with another stainless steel one if I >can find it. > >Any ideas? > >Comments? Unless you're doing an exact MoPar replacement then as long as the lengths are correct you shouldn't be concerned. I've not seen any performance exhaust mufflers that are perfect matches. I replaced my factory exhaust system with a Borla SS set and the pipes were larger in diameter, there was no reasonator and the mufflers were smaller. But the double walled chrome tipes still came out the back where they should be. And there is no comparison to the tone improvement. |
#3
|
|||
|
|||
Anyone replace the muffler on their Chrysler 300m? What did youuse?
BobMCT wrote:
> > I've been looking into various brands (Walker, Magnaflow, > > Flowmaster, etc) and can't really find anything made with > > stainless steel that matches the dimensions of the factory > > OEM muffler. > > Unless you're doing an exact MoPar replacement then as long as the > lengths are correct you shouldn't be concerned. I've not seen any > performance exhaust mufflers that are perfect matches. > > I replaced my factory exhaust system with a Borla SS set and the > pipes were larger in diameter, there was no reasonator and the > mufflers were smaller. But the double walled chrome tipes still > came out the back where they should be. And there is no comparison > to the tone improvement. My current muffler is still functional and intact, but when-ever the car has been put on a hoist, it's been pointed out that the muffler has many outer-shell perforations - none of which seems to be causing any changes to the exhaust sound. The only thing I want out of my exhaust system is for it to be quiet. I have no care or interest at all to try to achieve any sort of exhaust tone our particular sound. Just quiet. Urban life is noisey enough as it is. I'm wondering if the degree of "muffling" is proportional to muffler volume... |
#4
|
|||
|
|||
Anyone replace the muffler on their Chrysler 300m? What did you use?
On Sat, 08 Dec 2012 20:04:36 -0500, MoPar Man > wrote:
>BobMCT wrote: > >> > I've been looking into various brands (Walker, Magnaflow, >> > Flowmaster, etc) and can't really find anything made with >> > stainless steel that matches the dimensions of the factory >> > OEM muffler. >> >> Unless you're doing an exact MoPar replacement then as long as the >> lengths are correct you shouldn't be concerned. I've not seen any >> performance exhaust mufflers that are perfect matches. >> >> I replaced my factory exhaust system with a Borla SS set and the >> pipes were larger in diameter, there was no reasonator and the >> mufflers were smaller. But the double walled chrome tipes still >> came out the back where they should be. And there is no comparison >> to the tone improvement. > >My current muffler is still functional and intact, but when-ever the car >has been put on a hoist, it's been pointed out that the muffler has many >outer-shell perforations - none of which seems to be causing any changes >to the exhaust sound. > >The only thing I want out of my exhaust system is for it to be quiet. > >I have no care or interest at all to try to achieve any sort of exhaust >tone our particular sound. Just quiet. Urban life is noisey enough as >it is. > >I'm wondering if the degree of "muffling" is proportional to muffler >volume... You could wrap the muffler with metal tape like they sell in home depot for ac ducts (metal tape, not duct tape). My main worry with perforated muffler would be exhaust gases getting into the car. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
What car would you people buy these days to replace a '00 300m ? | MoPar Man | Chrysler | 0 | September 11th 12 01:31 AM |
Time to replace the original factory battery in my '00 300m? | MoPar Man | Chrysler | 6 | October 2nd 10 02:12 AM |
Repost of my earlier scans: 1999 Chrysler 300M Black 300M Logo 35mm.jpg 206805 bytes | HEMI-Powered @ [email protected] | Auto Photos | 0 | December 4th 07 12:12 PM |
2000 300m headlight replace-HELP | Fred[_6_] | Chrysler | 9 | January 27th 07 05:33 PM |
Focal 2002 Chrysler 300M (ultra-modified 300M) | MoPar Man | Chrysler | 1 | January 8th 06 07:43 PM |