A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » Honda
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Bolt Removal Problems



 
 
Thread Tools Display Modes
  #1  
Old September 23rd 04, 11:28 PM
Caroline
external usenet poster
 
Posts: n/a
Default Bolt Removal Problems

Update:
Unfastening the bolt connecting the rear lower control arm and trailing arm was
as ugly as others in the archives reported. I never actually got it free from
the bushing or its nut.

I never tried a torch, but that would be my next suggestion.

I eventually drilled and cut (by hand) the outside-most control arm
bushing/bolt. Then I ground down the female bolt receptacle (it's not actually a
nut, unfortunately, or I would have snapped it off, the way I did with the strut
fork bolt) welded to the trailing arm. I used a cheap-o electric hand drill and
grinding stone attachment. Grinding it down was no fun but at least I could see
some kind of steady progress. Cobalt drill bits are essential but still very,
very slow, even with the best cutting oil.

I installed the "new" (= 8k miles used) control arm last night, attaching it
with a separate nut at the trailing arm, as I think Eric and/or others
suggested. The new strut and control arm did not fix the tilt, but I wasn't
expecting it too.

The ride seems a bit smoother, but I may have talked myself into this.

I took apart the old strut in my suspension course today, borrowing the school's
spring compressor. The shock absorber seemed in excellent shape at 157k miles
old. The spring is a tougher call.

I reckon I spent around $35 just on cutting tools for this job. About half the
tools are broken or now severely worn. I'm worn, too! :-)

I am contemplating doing the other side but not for another week or so.
Meanwhile, the other side's bolts get sprayed with PB Blaster regularly. Not
that I have much hope this will help.

Moral of the story: The classic, "If it ain't broke, don't fix it"?

I dunno. I learned a lot: -)


Ads
  #2  
Old September 24th 04, 12:31 AM
John Ings
external usenet poster
 
Posts: n/a
Default

On Thu, 23 Sep 2004 22:28:53 GMT, "Caroline"
> wrote:

> I used a cheap-o electric hand drill and
>grinding stone attachment. Grinding it down was no fun


I bet! Is there any chance you can get ahold of an air tool?
A die grinder with a 3" abrasive cutoff wheel is the weapon of choice.
Electric drills just don't turn fast enough.


  #3  
Old September 24th 04, 06:25 AM
Caroline
external usenet poster
 
Posts: n/a
Default

"John Ings" > wrote
> On Thu, 23 Sep 2004 22:28:53 GMT, "Caroline"
> > wrote:
>
> > I used a cheap-o electric hand drill and
> >grinding stone attachment. Grinding it down was no fun

>
> I bet! Is there any chance you can get ahold of an air tool?
> A die grinder with a 3" abrasive cutoff wheel is the weapon of choice.
> Electric drills just don't turn fast enough.


Hi John, thanks for the suggestion. I'm a little overbudget on "tool toys" right
now, but I'll make some inquiries of classmates in my auto course and ponder it
for a few weeks before I go seriously after the other rear shock assembly, if I
go after it. I also want to keep an eye on my "re-design" of the one rear
trailing arm/control arm linkage for awhile.

At least I am now the proud owner of a 115 psi, 8 gallon reservoir, "uses oil"
air compressor (which may or may not do the trick for this tool you suggest).


  #4  
Old September 24th 04, 01:05 PM
John Ings
external usenet poster
 
Posts: n/a
Default

On Fri, 24 Sep 2004 05:25:35 GMT, "Caroline"
> wrote:

>At least I am now the proud owner of a 115 psi, 8 gallon reservoir, "uses oil"
>air compressor (which may or may not do the trick for this tool you suggest).


Then get a die grinder with a cutoff wheel. They're relatively cheap
as air tools go. Get one without a guard or with a removable guard.
They are more dangerous to use, but often you just can't get the ones
with a guard into confined spaces.

Small compressors sometimes don't pack enough oomph for big air tools
like 3/4" impact wrenches, but they are plenty good enough for things
like a die grinder, air chisels, air ratchets etc. I worked on cars
for a long time before I discovered air tools, and when I did wished I
had found out about them earlier.



 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
1996 Dodge Grand Caravan LE AC/Heater Blower, Relay and Resistor Block Problems 101 HeadlessHorseman Dodge 0 January 5th 05 03:49 PM


All times are GMT +1. The time now is 10:44 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.