If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Smell of melted plastic and no way to start.93/740i
During the driving was smell of plastic. After stop is no way to start
engine. In air condition compressor area is lot of black plastic melted parts like thick folia. Where from could by this plastic? Why engine is not starting? (Fuel pump is not running). All small fuses are OK. Please help. |
Ads |
#2
|
|||
|
|||
Smell of melted plastic and no way to start.93/740i
"pj" > wrote in message news:rwh_j.293192$pM4.22970@pd7urf1no... > During the driving was smell of plastic. After stop is no way to start > engine. In air condition compressor area is lot of black plastic melted > parts like thick folia. Where from could by this plastic? Why engine is > not starting? (Fuel pump is not running). All small fuses are OK. Please > help. > Well obviously something has melted. It could be some electrical or mechanical part or some foreign object (I got a plastic bag caught on the exhaust once - terrible smell, but no damage). Perhaps you left something under the bonnet (hood US), or some of the sound insulation foam has fallen off the underside. Once it has all cooled down have a good look, perhaps you can work out what is missing. Starter [solenoid], fuel pump, ignition all sound possible. |
#3
|
|||
|
|||
Smell of melted plastic and no way to start.93/740i
"pj" > wrote in message news:rwh_j.293192$pM4.22970@pd7urf1no... > During the driving was smell of plastic. After stop is no way to start > engine. In air condition compressor area is lot of black plastic melted > parts like thick folia. Where from could by this plastic? Why engine is > not starting? (Fuel pump is not running). All small fuses are OK. Please > help. >do we have any plastic parts in A/C copmpressor - looks like this plastic >stuff was from copressor - it is possible? George |
#4
|
|||
|
|||
Smell of melted plastic and no way to start.93/740i
after replacing stuck A/C compressor, hot engine wont start (only hot). How
to read cods? Pushing 5 times pedal to the end is not working ? Do I have to unlock option of reading cods? Thanks for any help. George |
#5
|
|||
|
|||
Smell of melted plastic and no way to start.93/740i
"pj" > wrote in message news:I6B0k.113$i01.74@pd7urf2no... > after replacing stuck A/C compressor, hot engine wont start (only hot). > How to read cods? Pushing 5 times pedal to the end is not working ? Do I > have to unlock option of reading cods? > Thanks for any help. > George > Garbled. Vapour lock, EMU damage, air inlet damage etc. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
740i has a high rev [3000rpm] at start up and stays there | [email protected] | BMW | 5 | September 18th 07 06:12 PM |
C5 hard start - gasoline smell | Keith | Corvette | 4 | June 6th 06 12:54 PM |
Gasoline smell on start up - Passat V6 | CasualBloke | VW water cooled | 0 | January 25th 05 02:21 PM |
HELP! E38 740i engine died at traffic lights and won't start??????? | Hugh Gundersen | BMW | 3 | December 13th 04 10:13 PM |