If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Wheel Bearing Questions...
So I figure I have a bad wheel bearing; unfortunately I can't figure
exactly what I'm going to have to do to fix it. The manual I have pretty much says don't mess with it and take the steering knuckle/hub assembly into a shop and have the bearing pressed. I called the nearby dealer and he said to just order the hub assembly and to put that on instead of pressing the bearing. Call the auto parts store for the hub assembly, and apparently you have to press the bearing that comes with the new hub assembly. What is the advantage of purchasing a new hub assembly as opposed to just the bearing? Is this really that hard that I should take it into a shop? I mean I know I need a press, and yes, I have access to one. what about an alignment? Why would I need one of those? I mean I guess I understand why, but If I'm not cranking on the tie rod or anything is it really going to throw it off that much? So many questions; and so little time before this thing decides its going to completely go out...thanks!! |
Ads |
#2
|
|||
|
|||
Wheel Bearing Questions...
|
#3
|
|||
|
|||
Wheel Bearing Questions...
On Jul 26, 11:26 pm, BläBlä
. s!rcre4p.c0m> wrote: > In article .com>, > says... > > > > > So I figure I have a bad wheel bearing; unfortunately I can't figure > > exactly what I'm going to have to do to fix it. The manual I have > > pretty much says don't mess with it and take the steering knuckle/hub > > assembly into a shop and have the bearing pressed. I called the > > nearby dealer and he said to just order the hub assembly and to put > > that on instead of pressing the bearing. Call the auto parts store > > for the hub assembly, and apparently you have to press the bearing > > that comes with the new hub assembly. What is the advantage of > > purchasing a new hub assembly as opposed to just the bearing? Is this > > really that hard that I should take it into a shop? I mean I know I > > need a press, and yes, I have access to one. what about an > > alignment? Why would I need one of those? I mean I guess I > > understand why, but If I'm not cranking on the tie rod or anything is > > it really going to throw it off that much? So many questions; and so > > little time before this thing decides its going to completely go > > out...thanks!! > > Mind reminding us what vehicle this is as I'm to tired to use telepathy > at this moment... Yeah, it's a 99 SL1 with about 113,000 miles...sorry |
#4
|
|||
|
|||
Wheel Bearing Questions...
|
#5
|
|||
|
|||
Wheel Bearing Questions...
"oh123" > wrote in message
oups.com... > So I figure I have a bad wheel bearing; unfortunately I can't figure > exactly what I'm going to have to do to fix it. The manual I have > pretty much says don't mess with it and take the steering knuckle/hub > assembly into a shop and have the bearing pressed. I called the > nearby dealer and he said to just order the hub assembly and to put > that on instead of pressing the bearing. Call the auto parts store > for the hub assembly, and apparently you have to press the bearing > that comes with the new hub assembly. What is the advantage of > purchasing a new hub assembly as opposed to just the bearing? Is this > really that hard that I should take it into a shop? I mean I know I > need a press, and yes, I have access to one. what about an > alignment? Why would I need one of those? I mean I guess I > understand why, but If I'm not cranking on the tie rod or anything is > it really going to throw it off that much? So many questions; and so > little time before this thing decides its going to completely go > out...thanks!! > Yeah, just take the knuckle to Saturn. take your car back to Saturn for alignment. I had it all done for <$200 including parts and what not...There was a good guide on the Saturn site. I can dig it up if you'd like? |
#6
|
|||
|
|||
Wheel Bearing Questions...
On Jul 27, 2:17 pm, "HyperCube33 \(Life2Death\)"
> wrote: > "oh123" > wrote in message > > oups.com... > > > > > > > So I figure I have a bad wheel bearing; unfortunately I can't figure > > exactly what I'm going to have to do to fix it. The manual I have > > pretty much says don't mess with it and take the steering knuckle/hub > > assembly into a shop and have the bearing pressed. I called the > > nearby dealer and he said to just order the hub assembly and to put > > that on instead of pressing the bearing. Call the auto parts store > > for the hub assembly, and apparently you have to press the bearing > > that comes with the new hub assembly. What is the advantage of > > purchasing a new hub assembly as opposed to just the bearing? Is this > > really that hard that I should take it into a shop? I mean I know I > > need a press, and yes, I have access to one. what about an > > alignment? Why would I need one of those? I mean I guess I > > understand why, but If I'm not cranking on the tie rod or anything is > > it really going to throw it off that much? So many questions; and so > > little time before this thing decides its going to completely go > > out...thanks!! > > Yeah, just take the knuckle to Saturn. take your car back to Saturn for > alignment. I had it all done for <$200 including parts and what not...There > was a good guide on the Saturn site. I can dig it up if you'd like?- Hide quoted text - > > - Show quoted text - Thanks for all your help and willingness to do so... A friend and I fixed the thing; quite a job. He's a mechanic, and had never seen a bearing like that. I can go into detail if you'd like...it took a lot longer than we both expected. To answer another question: How did I come to the conclusion it was a wheel bearing? Well, it was making a thumping noise for quite some time, around a year or so. Of course it got progressively worse, and I began to have premonissions that at some point, probably around 3 am, my tire would fall off and I would go crashing into the woods and become a missing person. It was classic wheel bearing symptoms, a thump-thump-thump type of noise, which earlier in it's time would only do it if the weight would shift onto the tire around a corner, or not do it if it would shift onto the other wheel. And apparently I was the only one to see this as odd, as a number of local shops that I took it to said it was fine, even after I explained what it was doing. Probably wanted nothing to do with changing that bearing. I know the guy who helped me said he'd never do another one. |
#7
|
|||
|
|||
Wheel Bearing Questions...
> wrote in message ups.com... > On Jul 27, 2:17 pm, "HyperCube33 \(Life2Death\)" > > wrote: >> "oh123" > wrote in message >> >> oups.com... >> >> >> >> >> >> > So I figure I have a bad wheel bearing; unfortunately I can't figure >> > exactly what I'm going to have to do to fix it. The manual I have >> > pretty much says don't mess with it and take the steering knuckle/hub >> > assembly into a shop and have the bearing pressed. I called the >> > nearby dealer and he said to just order the hub assembly and to put >> > that on instead of pressing the bearing. Call the auto parts store >> > for the hub assembly, and apparently you have to press the bearing >> > that comes with the new hub assembly. What is the advantage of >> > purchasing a new hub assembly as opposed to just the bearing? Is this >> > really that hard that I should take it into a shop? I mean I know I >> > need a press, and yes, I have access to one. what about an >> > alignment? Why would I need one of those? I mean I guess I >> > understand why, but If I'm not cranking on the tie rod or anything is >> > it really going to throw it off that much? So many questions; and so >> > little time before this thing decides its going to completely go >> > out...thanks!! >> >> Yeah, just take the knuckle to Saturn. take your car back to Saturn for >> alignment. I had it all done for <$200 including parts and what >> not...There >> was a good guide on the Saturn site. I can dig it up if you'd like?- Hide >> quoted text - >> >> - Show quoted text - > > Thanks for all your help and willingness to do so... > > A friend and I fixed the thing; quite a job. He's a mechanic, and had > never seen a bearing like that. > > I can go into detail if you'd like...it took a lot longer than we both > expected. > > To answer another question: How did I come to the conclusion it was a > wheel bearing? Well, it was making a thumping noise for quite some > time, around a year or so. Of course it got progressively worse, and > I began to have premonissions that at some point, probably around 3 > am, my tire would fall off and I would go crashing into the woods and > become a missing person. > > It was classic wheel bearing symptoms, a thump-thump-thump type of > noise, which earlier in it's time would only do it if the weight would > shift onto the tire around a corner, or not do it if it would shift > onto the other wheel. And apparently I was the only one to see this > as odd, as a number of local shops that I took it to said it was fine, > even after I explained what it was doing. Probably wanted nothing to > do with changing that bearing. I know the guy who helped me said he'd > never do another one. > A year? Jesus. I can feel a slight misbalance in my tires and I usually freak out. I can also feel when my tires are low as to how they sound... I'm a freak for sure |
#8
|
|||
|
|||
Wheel Bearing Questions...
On Aug 14, 8:52 am, "HyperCube33 \(Life2Death\)"
> wrote: > > wrote in message > > ups.com... > > > > > > > On Jul 27, 2:17 pm, "HyperCube33 \(Life2Death\)" > > > wrote: > >> "oh123" > wrote in message > > groups.com... > > >> > So I figure I have a bad wheel bearing; unfortunately I can't figure > >> > exactly what I'm going to have to do to fix it. The manual I have > >> > pretty much says don't mess with it and take the steering knuckle/hub > >> > assembly into a shop and have the bearing pressed. I called the > >> > nearby dealer and he said to just order the hub assembly and to put > >> > that on instead of pressing the bearing. Call the auto parts store > >> > for the hub assembly, and apparently you have to press the bearing > >> > that comes with the new hub assembly. What is the advantage of > >> > purchasing a new hub assembly as opposed to just the bearing? Is this > >> > really that hard that I should take it into a shop? I mean I know I > >> > need a press, and yes, I have access to one. what about an > >> > alignment? Why would I need one of those? I mean I guess I > >> > understand why, but If I'm not cranking on the tie rod or anything is > >> > it really going to throw it off that much? So many questions; and so > >> > little time before this thing decides its going to completely go > >> > out...thanks!! > > >> Yeah, just take the knuckle to Saturn. take your car back to Saturn for > >> alignment. I had it all done for <$200 including parts and what > >> not...There > >> was a good guide on the Saturn site. I can dig it up if you'd like?- Hide > >> quoted text - > > >> - Show quoted text - > > > Thanks for all your help and willingness to do so... > > > A friend and I fixed the thing; quite a job. He's a mechanic, and had > > never seen a bearing like that. > > > I can go into detail if you'd like...it took a lot longer than we both > > expected. > > > To answer another question: How did I come to the conclusion it was a > > wheel bearing? Well, it was making a thumping noise for quite some > > time, around a year or so. Of course it got progressively worse, and > > I began to have premonissions that at some point, probably around 3 > > am, my tire would fall off and I would go crashing into the woods and > > become a missing person. > > > It was classic wheel bearing symptoms, a thump-thump-thump type of > > noise, which earlier in it's time would only do it if the weight would > > shift onto the tire around a corner, or not do it if it would shift > > onto the other wheel. And apparently I was the only one to see this > > as odd, as a number of local shops that I took it to said it was fine, > > even after I explained what it was doing. Probably wanted nothing to > > do with changing that bearing. I know the guy who helped me said he'd > > never do another one. > > A year? Jesus. I can feel a slight misbalance in my tires and I usually > freak out. I can also feel when my tires are low as to how they sound... > > I'm a freak for sure - Hide quoted text - > > - Show quoted text - well, I noticed it, but what can you do? Fix it I suppose, but i guess that is how cars go...turn up the radio, and the problem momentarily disappears. |
#9
|
|||
|
|||
Wheel Bearing Questions...
"oh123" > wrote in message oups.com... > So I figure I have a bad wheel bearing; unfortunately I can't figure > exactly what I'm going to have to do to fix it. The manual I have > pretty much says don't mess with it and take the steering knuckle/hub > assembly into a shop and have the bearing pressed. I called the > nearby dealer and he said to just order the hub assembly and to put > that on instead of pressing the bearing. Call the auto parts store > for the hub assembly, and apparently you have to press the bearing > that comes with the new hub assembly. What is the advantage of > purchasing a new hub assembly as opposed to just the bearing? Is this > really that hard that I should take it into a shop? I mean I know I > need a press, and yes, I have access to one. what about an > alignment? Why would I need one of those? I mean I guess I > understand why, but If I'm not cranking on the tie rod or anything is > it really going to throw it off that much? So many questions; and so > little time before this thing decides its going to completely go > out...thanks!! > Google is your friend. http://groups.google.ca/groups?as_q=...=2006&safe=off especially (IMHO) http://groups.google.ca/group/rec.au...e98ea9 6e1ac9 and http://groups.google.ca/group/rec.au...5e3b0f a9a162 Good luck, YMMV |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
AWA [OFFER] OEM WHEEL HUB BEARING | [email protected] | General | 0 | April 4th 06 01:53 PM |
Right Rear Axle Shaft Bearing Questions '88 XJ Dana 35 | dave AKA vwdoc1 | Jeep | 4 | August 4th 05 11:15 PM |
Bearing Races Question and Wheel Bearing Pack Question | Kevin Holzer | VW air cooled | 3 | June 11th 05 05:51 AM |
Dana 44 bearing questions | George | Jeep | 3 | January 9th 05 08:24 PM |
WHEEL BEARING | FOR1196D | 4x4 | 8 | April 3rd 04 03:37 PM |