If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
351 crate motor?
Anyone had any experience with Ford Racings 351 crate motor, the one they
say is HD. 250 hp,4bbl intake, and cost $2,800? Thinking of putting one in my 71 coupe, the Ford parts website says it makes 350 ft lbs of tq. I would like alittle more hp than 250 say around 300, but this price is in my budget. Thanks Dean. |
Ads |
#2
|
|||
|
|||
351 crate motor?
Nothing says you can't take the crate motor and build it up from there....
OTOH, there is no replacement for displacement and it wouldn't be hard to take a seasoned block and stroke it out to 400 inches... add some decent heads and you are well on your way to 300+ HP "Dean" > wrote in message ... > Anyone had any experience with Ford Racings 351 crate motor, the one they > say is HD. 250 hp,4bbl intake, and cost $2,800? Thinking of putting one in > my 71 coupe, the Ford parts website says it makes 350 ft lbs of tq. I would > like alittle more hp than 250 say around 300, but this price is in my > budget. > > Thanks Dean. > > |
#3
|
|||
|
|||
351 crate motor?
Dean wrote:
> Anyone had any experience with Ford Racings 351 crate motor, the one they > say is HD. 250 hp,4bbl intake, and cost $2,800? Thinking of putting one in > my 71 coupe, the Ford parts website says it makes 350 ft lbs of tq. I would > like alittle more hp than 250 say around 300, but this price is in my > budget. That's not the one you want. You really want the marine version of the 351W. I don't recall how much it costs these days, but it's good for almost 350hp normally aspirated. They also more or less drop in to a Fox Mustang with some minor alterations. Cheers, |
#4
|
|||
|
|||
351 crate motor?
"Dean" > wrote in message ... > Anyone had any experience with Ford Racings 351 crate motor, the one they > say is HD. 250 hp,4bbl intake, and cost $2,800? Thinking of putting one in > my 71 coupe, the Ford parts website says it makes 350 ft lbs of tq. I > would like alittle more hp than 250 say around 300, but this price is in > my budget. > I spent that much rebuilding my 302 that's in the 'Chero. It's a .060" ob C8 block with gasket matched C8 iron heads, RPM air gap intake and a little more cam than stock. It puts out ~270hp at the flywheel, and that's with 40 cid less than that brand new 351W. Installed. The other end is the 351W that's in my '69. It's a .060" ob D9 block. GT40-X heads. Comp Cams XE262H cam. Performer intake. CHP 393 stroker crank. full balance. How 'bout 420hp and 480lb/ft tq? This cost in the neighborhood of $4k installed. I suggest you do a bit more research. I know getting a crate engine is a lot easier, but there are advantages to having a motor built for you. My builder asked a lot of questions before he started building. First obviously is what my budget is. Next is what am I going to use it for. Am I planning on having some fun with it later on? Any trips to the circle, roadcourse or straight line track (regularly, rarely, or never)? These are things a builder you actually talk to can discuss which way to go with the build. With a crate, you get what you get. -- Scott W. '66 HCS Mustang 289 '68 Ranchero 500 302 '69 Mustang Sportsroof 351W ThunderSnake #57 http://home.comcast.net/~vanguard92/ |
#5
|
|||
|
|||
351 crate motor?
Ritz wrote:
> Dean wrote: > >> Anyone had any experience with Ford Racings 351 crate motor, the one >> they say is HD. 250 hp,4bbl intake, and cost $2,800? Thinking of >> putting one in my 71 coupe, the Ford parts website says it makes 350 >> ft lbs of tq. I would like alittle more hp than 250 say around 300, >> but this price is in my budget. > > > That's not the one you want. You really want the marine version of the > 351W. I don't recall how much it costs these days, but it's good for > almost 350hp normally aspirated. They also more or less drop in to a > Fox Mustang with some minor alterations. There's also the 385hp 351-HO SVO (PN M-6007-A351) crate engine. List is a little over $4k. That's a bit more than the $2,800 quoted above, but it's also over 50% more horsepower in a normally aspirated Ford crate engine. And then there's the 351 GT-40 SVO assembly (PN M-6007-B351), which comes with cast-iron heads and an auto-trans flexplate. Using SVO’s dual-plane intake (PN M-9424-Z351), a 750-cfm Holley, and headers, it’s still rated at 346 hp and 364 lb-ft. Don't forget that there are also lots of places doing the old standard...347 stroker which can produce a lot of normally aspirated power on a budget as well. Good luck! Cheers, |
#6
|
|||
|
|||
351 crate motor?
Dean, Earlier this year my daughter's b/f started a complete
drivetrain replacement project for his '65 coupe. We decided early on to replace the non-original 302 w/a 351 and looked at that crate engine also. He eventually bought a remanufactured 351 with the same heads and cam (reputable machinist shop) for $1000 less. If other items weren't needed for the project he'd have bought the crate engine. Headers, 4BBL and a set of used 1.7 roller rockers later he has a car that outruns my 14.2 sec. '00 GT from a roll ('65 needs limited slip and ratio change). bradtx |
#7
|
|||
|
|||
351 crate motor?
What is "4bbl intake", please?
-- Scotter "Jim Warman" > wrote in message news:aLLdf.106073$S4.36724@edtnps84... > Nothing says you can't take the crate motor and build it up from there.... > OTOH, there is no replacement for displacement and it wouldn't be hard to > take a seasoned block and stroke it out to 400 inches... add some decent > heads and you are well on your way to 300+ HP > > > "Dean" > wrote in message > ... >> Anyone had any experience with Ford Racings 351 crate motor, the one they >> say is HD. 250 hp,4bbl intake, and cost $2,800? Thinking of putting one >> in >> my 71 coupe, the Ford parts website says it makes 350 ft lbs of tq. I > would >> like alittle more hp than 250 say around 300, but this price is in my >> budget. >> >> Thanks Dean. >> >> > > |
#8
|
|||
|
|||
351 crate motor?
Scotter wrote:
> What is "4bbl intake", please? > An intake manifold that will accep a 4-barrel carburetor. Cheers, |
#9
|
|||
|
|||
351 crate motor?
Scotter wrote:
> What is "4bbl intake", please? > OMG it's finally happened. The old fashioned carburetor and its associated hardware is not recognized by the masses anymore... Rob |
#10
|
|||
|
|||
351 crate motor?
trainfan1 wrote:
> Scotter wrote: > >> What is "4bbl intake", please? >> > > OMG it's finally happened. The old fashioned carburetor and its > associated hardware is not recognized by the masses anymore... > > Rob Anyone younger than about 30 or 35 that isn't a hotrodder probably has never even seen one on a production car. Personally, I prefer fuel injection. It's a little more complex, but you can more finely tune the engine and you don't have to worry about a cranky choke when the weather gets cold. 8-) I have an old mid-60's Jeep Commando that I use occasionally to plow my driveway. I was rebuilding the carb a few months ago and must have had a dozen people ask me what that funny looking thing on my workbench was. The rebuild kit I got from my usual parts supplier looked like it had about 30 years worth of dust on the box. 8-) Cheers, |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
LIDAR Trial this Week | [email protected] | Driving | 17 | April 9th 06 02:44 AM |
Hemi crate motor package? | Bret Ludwig | Chrysler | 5 | October 10th 05 05:27 PM |
1996 Dodge Grand Caravan LE AC/Heater Blower, Relay and Resistor Block Problems 101 | HeadlessHorseman | Dodge | 0 | January 5th 05 02:49 PM |
Climatronic Diagnostic Controls | Luís Lourenço | Audi | 1 | November 12th 04 08:22 AM |