If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Ideas for a home alignment caster/camber wheel jig to lock to 14inch to 20 inch wheel rims
Asking for ideas from those who craft tools at home out of stock metal.
o Who don't just put a magnetic camber gauge on the rim or rotor With a handful of vehicles coming due for routine caster, camber, and toe checks, I'm thinking of building a simple wheel jig to make it easier to lock the camber gauge FLAT onto variously sized wheel rims. Perhaps a bit better than building this camber gauge tool at home? <https://youtu.be/Ew87fLr6Omw> But not as sophisticated as this type of wheel jig: <https://youtu.be/5koH0U3qOvA> But with the addition of toe-plate functionality of this type: <https://youtu.be/TTkSwuXKWpM> But by simply extending the horizontal arm, sort of like this guy did: <https://youtu.be/hYOVRwKrSrQ?t=661> Here's what I'm thinking, by way of asking for design improvements. o It's two steel slats (or angle iron) and a few bolts only o The two slats are bolted together in an upside-down T shape o The lower horizontal slat contains the two lower seating pins o The upper vertical slat holds the one upper seating pin o The seating pins are simply bolts with a rubber cap for rim protection o The upper vertical slat's pin hole is slotted for adjustment o The lower horizontal slat's holes are spaced for adjustment Optionally, I can add an "extension" to both ends of the horizontal slat, which then has to clear the bulge of the tire, which extends the horizontal slat to the front and back of the tire, where there is a jig saw cut in the end of each extension, to hole a tape measure firmly in a one-man operation to measure to the centerline of the vehicle chassis from underneath. Total components appear to be: 1. Two approximately 24" steel slats (steel for magnetic camber gauges) 2. Three rubber-capped 1/4-inch nut and bolts to act as the rim pins 3. One nut and bolt to bolt the T wheel jig together And for the optional toe slats: 4. A one-foot pair of extensions, slotted by a jig saw on one end 5. Drilled and bolted to the horizontal slat on the other end Any helpful suggestions from those of you who have build such tools? o Total cost should be a couple of bucks I would think (but haven't calculated yet as the design is the starting point) |
Ads |
#2
|
|||
|
|||
Ideas for a home alignment caster/camber wheel jig to lock to14inch to 20 inch wheel rims
On Thursday, May 30, 2019 at 3:30:53 PM UTC-5, Arlen G. Holder wrote:
> Asking for ideas from those who craft tools at home out of stock metal. > o Who don't just put a magnetic camber gauge on the rim or rotor > > With a handful of vehicles coming due for routine caster, camber, and toe > checks, I'm thinking of building a simple wheel jig to make it easier to > lock the camber gauge FLAT onto variously sized wheel rims. > > Perhaps a bit better than building this camber gauge tool at home? > <https://youtu.be/Ew87fLr6Omw> > > But not as sophisticated as this type of wheel jig: > <https://youtu.be/5koH0U3qOvA> > > But with the addition of toe-plate functionality of this type: > <https://youtu.be/TTkSwuXKWpM> > > But by simply extending the horizontal arm, sort of like this guy did: > <https://youtu.be/hYOVRwKrSrQ?t=661> > > Here's what I'm thinking, by way of asking for design improvements. > o It's two steel slats (or angle iron) and a few bolts only > o The two slats are bolted together in an upside-down T shape > o The lower horizontal slat contains the two lower seating pins > o The upper vertical slat holds the one upper seating pin > o The seating pins are simply bolts with a rubber cap for rim protection > o The upper vertical slat's pin hole is slotted for adjustment > o The lower horizontal slat's holes are spaced for adjustment > > Optionally, I can add an "extension" to both ends of the horizontal slat, > which then has to clear the bulge of the tire, which extends the horizontal > slat to the front and back of the tire, where there is a jig saw cut in the > end of each extension, to hole a tape measure firmly in a one-man operation > to measure to the centerline of the vehicle chassis from underneath. > > Total components appear to be: > 1. Two approximately 24" steel slats (steel for magnetic camber gauges) > 2. Three rubber-capped 1/4-inch nut and bolts to act as the rim pins > 3. One nut and bolt to bolt the T wheel jig together > > And for the optional toe slats: > 4. A one-foot pair of extensions, slotted by a jig saw on one end > 5. Drilled and bolted to the horizontal slat on the other end > > Any helpful suggestions from those of you who have build such tools? > o Total cost should be a couple of bucks I would think > (but haven't calculated yet as the design is the starting point) everythingdiy lady. What kind of an accent does she have? I never heard anything like that before. |
#3
|
|||
|
|||
Ideas for a home alignment caster/camber wheel jig to lock to14inch to 20 inch wheel rims
> > > > Any helpful suggestions from those of you who have build such tools? > > o Total cost should be a couple of bucks I would think > > (but haven't calculated yet as the design is the starting point) > I used to do this with a light and projection lens and mirrors. Now with laser pointers, you should be able to do something really slick. m |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
caster camber | glen | Jeep | 2 | July 30th 09 02:48 AM |
old camber/caster gauge usage | Brent P | Driving | 5 | October 1st 05 02:41 PM |
Camber Wheel Alignment on Caprice | MechTherapy | Technology | 5 | June 26th 05 05:05 AM |
Camber/Caster/Toe how bad the situation | [email protected] | Technology | 2 | April 23rd 05 07:31 PM |
Wheel Camber | Mel P. | VW air cooled | 6 | November 6th 04 06:05 PM |