If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
How to remove master cylinder on 1950 Chev Fleetline Deluxe??
Any tips / experience regarding removal of the master cylinder on a 1950
Chevy Fleetline Deluxe?? I am stumped! Does the pivoting part on the master cylinder slide out after removing spring and bolt through the plunger, or does the whole arm up to the brake pedal have to be removed with it??? I CANNOT see how to unbolt up there if so. Just can't reach it... under, over, sideways,... does one have to remove engine and or body from frame just to remove the master cylinder??? Or does one need to cut out the floor board??? I am quite frustrated with it at this point to put it mildly! |
#2
|
|||
|
|||
How to remove master cylinder on 1950 Chev Fleetline Deluxe??
"In2hoppn" > wrote in message news:J-ydncSwKYlANNzUnZ2dnUVZ_ojinZ2d@metrocastcablevisio n.com... > Any tips / experience regarding removal of the master cylinder on a 1950 > Chevy Fleetline Deluxe?? > I am stumped! > Does the pivoting part on the master cylinder slide out after removing > spring and bolt through the plunger, or does the whole arm up to the brake > pedal have to be removed with it??? I CANNOT see how to unbolt up there > if > so. Just can't reach it... under, over, sideways,... does one have to > remove engine and or body from frame just to remove the master cylinder??? > Or does one need to cut out the floor board??? I am quite frustrated with > it at this point to put it mildly! > > Here is the brake Chapter from the service manual http://chevy.oldcarmanualproject.com...rakes/5_01.HTM Here is the official way of doing it: http://chevy.oldcarmanualproject.com...rakes/5_14.HTM The official instructions for removal of the cyly=inder are on this page: http://chevy.oldcarmanualproject.com...rakes/5_15.HTM Info on assembly: http://chevy.oldcarmanualproject.com...rakes/5_16.HTM I have removed master cylinders complete with the the pedal extensions by removing the pedal shaft bolts at the top rather than removing the shaft pivot pin etc as described in instruction #3. The hydraulic lines have to be undone from below the car as likewise the clutch linkage and the two master cylinder chassis mounting bolts. The master cylinder can then be manouvered out. Watch out for dripping brake fluid in the eyes. Hope that helps. .................................................. ............... Posted via TITANnews - Uncensored Newsgroups Access >>>> at http://www.TitanNews.com <<<< -=Every Newsgroup - Anonymous, UNCENSORED, BROADBAND Downloads=- |
#3
|
|||
|
|||
How to remove master cylinder on 1950 Chev Fleetline Deluxe??
I need help installing a new master cylinder on 51 Chevy styline deluxe don't exactly know it bolts on to.the previous owner had removed it before I bought the car.if you can guide or show me a picture more or less where it sits thanks..
|
#4
|
|||
|
|||
How to remove master cylinder on 1950 Chev Fleetline Deluxe??
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
1952 Chev Fleetline DeLuxe 2 dr sdn fVr | Peter C[_2_] | Car Show Photos | 3 | November 7th 08 09:09 AM |
1952 Chev Fleetline DeLuxe 2 dr sdn fender trim | Peter C[_2_] | Car Show Photos | 0 | November 7th 08 06:53 AM |
1952 Chev Fleetline DeLuxe 2 dr sdn dash | Peter C[_2_] | Car Show Photos | 0 | November 7th 08 06:52 AM |
1952 Chev Fleetline DeLuxe 2 dr sdn rVr | Peter C[_2_] | Car Show Photos | 0 | November 7th 08 06:52 AM |
help abs brake pump why would brake fluid come out of the master cylinder when ( top ) when brakes are applied when rotters are hot master cylinder has been changed system has been bled 2nd help should pump motor make a sound when ke | envirokid | Ford Explorer | 0 | April 8th 05 09:10 PM |