If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Front Brake pad replacement 2003 Town and Country TC
Front Brake pad replacement 2003 Town and Country TC
Done at 34k miles. Dealer price $89 on special My cost: $38 pads $3.00 brake cleaner $3.00 antisqeal gel Time - 2+ hours Since there is little on the subject I thought I'd throw in my 2 cents. I got some middle of the road Raybestos pads for around $38 for the set. Also got some brake pad antisqueal sauce and a 6 point 13/16" socket and new 1/2" ratchet from Sears. The 6 point socket is for removing the 2 bolts at the rear of the caliper without stripping them. To hang the calipers use a sturdy wire or coat hanger and make sure it is very secure - these things are very heavy compared to smaller vehicles. To get the caliper off of the rotor you will need to carefully wrangle a c-clamp into the hole on the caliper and bear down on the lip of the inner pad and the rear of the caliper. It is tough but you only need it to move a little bit. Use a screw driver to carefully remove the old pads noting how they fit into the caliper. Before cranking down the piston with a C-clamp put the rear pad into position. After in position use the c-clamp to compress the piston all the way down. Next put the outside pad on. It will take some wrestling but you can do it. Remount on the wheel assembly and you are done. Don't forget the antisqueal sauce! |
Ads |
#2
|
|||
|
|||
I sure hope you performed a brake fluid flush, when pushing back the piston
crack the bleeder screw so the old fluid pours out rather than is kept in the caliper or forced back up through the system. Brake fluid should be changed every 2 years on an ABS equipped car and probably on a non ABS equipped car though there aren't as many expensive parts to rust out. "Dantanna" > wrote in message ... > Front Brake pad replacement 2003 Town and Country TC > > Done at 34k miles. > > Dealer price $89 on special > > My cost: > > $38 pads > $3.00 brake cleaner > $3.00 antisqeal gel > Time - 2+ hours > > > Since there is little on the subject I thought I'd throw in my 2 cents. I > got some middle of the road Raybestos pads for around $38 for the set. > Also > got some brake pad antisqueal sauce and a 6 point 13/16" socket and new > 1/2" > ratchet from Sears. The 6 point socket is for removing the 2 bolts at > the > rear of the caliper without stripping them. > > To hang the calipers use a sturdy wire or coat hanger and make sure it is > very secure - these things are very heavy compared to smaller vehicles. > > To get the caliper off of the rotor you will need to carefully wrangle a > c-clamp into the hole on the caliper and bear down on the lip of the inner > pad and the rear of the caliper. It is tough but you only need it to move > a > little bit. > > Use a screw driver to carefully remove the old pads noting how they fit > into > the caliper. > > Before cranking down the piston with a C-clamp put the rear pad into > position. After in position use the c-clamp to compress the piston all > the > way down. > > Next put the outside pad on. It will take some wrestling but you can do > it. > > Remount on the wheel assembly and you are done. > > Don't forget the antisqueal sauce! > > |
#3
|
|||
|
|||
I sure hope you performed a brake fluid flush, when pushing back the piston
crack the bleeder screw so the old fluid pours out rather than is kept in the caliper or forced back up through the system. Brake fluid should be changed every 2 years on an ABS equipped car and probably on a non ABS equipped car though there aren't as many expensive parts to rust out. "Dantanna" > wrote in message ... > Front Brake pad replacement 2003 Town and Country TC > > Done at 34k miles. > > Dealer price $89 on special > > My cost: > > $38 pads > $3.00 brake cleaner > $3.00 antisqeal gel > Time - 2+ hours > > > Since there is little on the subject I thought I'd throw in my 2 cents. I > got some middle of the road Raybestos pads for around $38 for the set. > Also > got some brake pad antisqueal sauce and a 6 point 13/16" socket and new > 1/2" > ratchet from Sears. The 6 point socket is for removing the 2 bolts at > the > rear of the caliper without stripping them. > > To hang the calipers use a sturdy wire or coat hanger and make sure it is > very secure - these things are very heavy compared to smaller vehicles. > > To get the caliper off of the rotor you will need to carefully wrangle a > c-clamp into the hole on the caliper and bear down on the lip of the inner > pad and the rear of the caliper. It is tough but you only need it to move > a > little bit. > > Use a screw driver to carefully remove the old pads noting how they fit > into > the caliper. > > Before cranking down the piston with a C-clamp put the rear pad into > position. After in position use the c-clamp to compress the piston all > the > way down. > > Next put the outside pad on. It will take some wrestling but you can do > it. > > Remount on the wheel assembly and you are done. > > Don't forget the antisqueal sauce! > > |
#4
|
|||
|
|||
To save money Chrysler used cheap (but functional) pads that product tons of
dust that turn the wheels black. A switch to ceramic pads eliminate that issue. Ceramic pads are standard on many makes of cars today, such as Honda and Toyota. In my opinion they are the way to go if you have mag style wheels. Richard. |
#5
|
|||
|
|||
To save money Chrysler used cheap (but functional) pads that product tons of
dust that turn the wheels black. A switch to ceramic pads eliminate that issue. Ceramic pads are standard on many makes of cars today, such as Honda and Toyota. In my opinion they are the way to go if you have mag style wheels. Richard. |
#6
|
|||
|
|||
Theoretically you are right. However, try to find the average brake shop that flushes fluid with a pad change. Right..... Doug On Tue, 21 Dec 2004 08:00:41 GMT, "Sam Steele" > wrote: >I sure hope you performed a brake fluid flush, when pushing back the piston >crack the bleeder screw so the old fluid pours out rather than is kept in >the caliper or forced back up through the system. Brake fluid should be >changed every 2 years on an ABS equipped car and probably on a non ABS >equipped car though there aren't as many expensive parts to rust out. >"Dantanna" > wrote in message ... >> Front Brake pad replacement 2003 Town and Country TC >> >> Done at 34k miles. >> >> Dealer price $89 on special >> >> My cost: >> >> $38 pads >> $3.00 brake cleaner >> $3.00 antisqeal gel >> Time - 2+ hours >> >> >> Since there is little on the subject I thought I'd throw in my 2 cents. I >> got some middle of the road Raybestos pads for around $38 for the set. >> Also >> got some brake pad antisqueal sauce and a 6 point 13/16" socket and new >> 1/2" >> ratchet from Sears. The 6 point socket is for removing the 2 bolts at >> the >> rear of the caliper without stripping them. >> >> To hang the calipers use a sturdy wire or coat hanger and make sure it is >> very secure - these things are very heavy compared to smaller vehicles. >> >> To get the caliper off of the rotor you will need to carefully wrangle a >> c-clamp into the hole on the caliper and bear down on the lip of the inner >> pad and the rear of the caliper. It is tough but you only need it to move >> a >> little bit. >> >> Use a screw driver to carefully remove the old pads noting how they fit >> into >> the caliper. >> >> Before cranking down the piston with a C-clamp put the rear pad into >> position. After in position use the c-clamp to compress the piston all >> the >> way down. >> >> Next put the outside pad on. It will take some wrestling but you can do >> it. >> >> Remount on the wheel assembly and you are done. >> >> Don't forget the antisqueal sauce! >> >> > |
#7
|
|||
|
|||
Theoretically you are right. However, try to find the average brake shop that flushes fluid with a pad change. Right..... Doug On Tue, 21 Dec 2004 08:00:41 GMT, "Sam Steele" > wrote: >I sure hope you performed a brake fluid flush, when pushing back the piston >crack the bleeder screw so the old fluid pours out rather than is kept in >the caliper or forced back up through the system. Brake fluid should be >changed every 2 years on an ABS equipped car and probably on a non ABS >equipped car though there aren't as many expensive parts to rust out. >"Dantanna" > wrote in message ... >> Front Brake pad replacement 2003 Town and Country TC >> >> Done at 34k miles. >> >> Dealer price $89 on special >> >> My cost: >> >> $38 pads >> $3.00 brake cleaner >> $3.00 antisqeal gel >> Time - 2+ hours >> >> >> Since there is little on the subject I thought I'd throw in my 2 cents. I >> got some middle of the road Raybestos pads for around $38 for the set. >> Also >> got some brake pad antisqueal sauce and a 6 point 13/16" socket and new >> 1/2" >> ratchet from Sears. The 6 point socket is for removing the 2 bolts at >> the >> rear of the caliper without stripping them. >> >> To hang the calipers use a sturdy wire or coat hanger and make sure it is >> very secure - these things are very heavy compared to smaller vehicles. >> >> To get the caliper off of the rotor you will need to carefully wrangle a >> c-clamp into the hole on the caliper and bear down on the lip of the inner >> pad and the rear of the caliper. It is tough but you only need it to move >> a >> little bit. >> >> Use a screw driver to carefully remove the old pads noting how they fit >> into >> the caliper. >> >> Before cranking down the piston with a C-clamp put the rear pad into >> position. After in position use the c-clamp to compress the piston all >> the >> way down. >> >> Next put the outside pad on. It will take some wrestling but you can do >> it. >> >> Remount on the wheel assembly and you are done. >> >> Don't forget the antisqueal sauce! >> >> > |
#8
|
|||
|
|||
Most I talk with do the fluid flush with pad replacement, the ghetto low
ball shops most likely won't but then you get what you pay for. "Doug" > wrote in message ... > > Theoretically you are right. > However, try to find the average brake shop that flushes fluid with a > pad change. > Right..... > > Doug > > > > > On Tue, 21 Dec 2004 08:00:41 GMT, "Sam Steele" > > wrote: > >>I sure hope you performed a brake fluid flush, when pushing back the >>piston >>crack the bleeder screw so the old fluid pours out rather than is kept in >>the caliper or forced back up through the system. Brake fluid should be >>changed every 2 years on an ABS equipped car and probably on a non ABS >>equipped car though there aren't as many expensive parts to rust out. >>"Dantanna" > wrote in message ... >>> Front Brake pad replacement 2003 Town and Country TC >>> >>> Done at 34k miles. >>> >>> Dealer price $89 on special >>> >>> My cost: >>> >>> $38 pads >>> $3.00 brake cleaner >>> $3.00 antisqeal gel >>> Time - 2+ hours >>> >>> >>> Since there is little on the subject I thought I'd throw in my 2 cents. >>> I >>> got some middle of the road Raybestos pads for around $38 for the set. >>> Also >>> got some brake pad antisqueal sauce and a 6 point 13/16" socket and new >>> 1/2" >>> ratchet from Sears. The 6 point socket is for removing the 2 bolts at >>> the >>> rear of the caliper without stripping them. >>> >>> To hang the calipers use a sturdy wire or coat hanger and make sure it >>> is >>> very secure - these things are very heavy compared to smaller vehicles. >>> >>> To get the caliper off of the rotor you will need to carefully wrangle a >>> c-clamp into the hole on the caliper and bear down on the lip of the >>> inner >>> pad and the rear of the caliper. It is tough but you only need it to >>> move >>> a >>> little bit. >>> >>> Use a screw driver to carefully remove the old pads noting how they fit >>> into >>> the caliper. >>> >>> Before cranking down the piston with a C-clamp put the rear pad into >>> position. After in position use the c-clamp to compress the piston all >>> the >>> way down. >>> >>> Next put the outside pad on. It will take some wrestling but you can do >>> it. >>> >>> Remount on the wheel assembly and you are done. >>> >>> Don't forget the antisqueal sauce! >>> >>> >> > |
#9
|
|||
|
|||
Most I talk with do the fluid flush with pad replacement, the ghetto low
ball shops most likely won't but then you get what you pay for. "Doug" > wrote in message ... > > Theoretically you are right. > However, try to find the average brake shop that flushes fluid with a > pad change. > Right..... > > Doug > > > > > On Tue, 21 Dec 2004 08:00:41 GMT, "Sam Steele" > > wrote: > >>I sure hope you performed a brake fluid flush, when pushing back the >>piston >>crack the bleeder screw so the old fluid pours out rather than is kept in >>the caliper or forced back up through the system. Brake fluid should be >>changed every 2 years on an ABS equipped car and probably on a non ABS >>equipped car though there aren't as many expensive parts to rust out. >>"Dantanna" > wrote in message ... >>> Front Brake pad replacement 2003 Town and Country TC >>> >>> Done at 34k miles. >>> >>> Dealer price $89 on special >>> >>> My cost: >>> >>> $38 pads >>> $3.00 brake cleaner >>> $3.00 antisqeal gel >>> Time - 2+ hours >>> >>> >>> Since there is little on the subject I thought I'd throw in my 2 cents. >>> I >>> got some middle of the road Raybestos pads for around $38 for the set. >>> Also >>> got some brake pad antisqueal sauce and a 6 point 13/16" socket and new >>> 1/2" >>> ratchet from Sears. The 6 point socket is for removing the 2 bolts at >>> the >>> rear of the caliper without stripping them. >>> >>> To hang the calipers use a sturdy wire or coat hanger and make sure it >>> is >>> very secure - these things are very heavy compared to smaller vehicles. >>> >>> To get the caliper off of the rotor you will need to carefully wrangle a >>> c-clamp into the hole on the caliper and bear down on the lip of the >>> inner >>> pad and the rear of the caliper. It is tough but you only need it to >>> move >>> a >>> little bit. >>> >>> Use a screw driver to carefully remove the old pads noting how they fit >>> into >>> the caliper. >>> >>> Before cranking down the piston with a C-clamp put the rear pad into >>> position. After in position use the c-clamp to compress the piston all >>> the >>> way down. >>> >>> Next put the outside pad on. It will take some wrestling but you can do >>> it. >>> >>> Remount on the wheel assembly and you are done. >>> >>> Don't forget the antisqueal sauce! >>> >>> >> > |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
93 town and country | Richard Seibert | Chrysler | 4 | November 27th 04 11:15 AM |
03 chrystler town and country radio replacement | fmyrtle | Chrysler | 2 | October 19th 04 06:13 PM |
2004 Chrysler Town and Country Minivan | Bob | Dodge | 5 | April 25th 04 03:47 AM |