If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Tranny Input Shaft Seal Install Tool - Help Please!
Hello!
What kind of home made sleeve tool can I make that does not require welding to install the tranny input shaft seal? I was thinking of a flat washer just a little smaller diameter as the input shaft seal and a short piece of pvc pipe and a rubber mallet. Thanks In Advance! Any help will be appreciated! |
Ads |
#2
|
|||
|
|||
Tranny Input Shaft Seal Install Tool - Help Please!
On Tue, 05 Aug 2008 17:45:24 +0200, > wrote:
> Hello! > What kind of home made sleeve tool can I make that does not require > welding to install the tranny input shaft seal? > > I was thinking of a flat washer just a little smaller diameter as the > input shaft seal and a short piece of pvc pipe and a rubber mallet. > > Thanks In Advance! > Any help will be appreciated! You can do it with a flat nosed punch/drift, make sure it has no sharp edges. Also make sure you get the seal square when you start, slowly round round and in it goes. Or if you have a large diameter pipe, type water or gas, preferably the same O.d as the seal you can tap it in with this using a heavy big hammer or short-shaft sledgehammer. J. -- Using Opera's revolutionary e-mail client: http://www.opera.com/mail/ |
#3
|
|||
|
|||
Tranny Input Shaft Seal Install Tool - Help Please!
The replacement input shaft seal does not have a metal outer edge.
Is it supposed to have one? If so, where can I get one? TIA ----------------------------------- On Aug 5, 12:18 pm, "P.J.Berg" > wrote: > On Tue, 05 Aug 2008 17:45:24 +0200, > wrote: > > Hello! > > What kind of home made sleeve tool can I make that does not require > > welding to install the tranny input shaft seal? > > > I was thinking of a flat washer just a little smaller diameter as the > > input shaft seal and a short piece of pvc pipe and a rubber mallet. > > > Thanks In Advance! > > Any help will be appreciated! > > You can do it with a flat nosed punch/drift, make sure it has no sharp > edges. > Also make sure you get the seal square when you start, slowly round round > and in it goes. > Or if you have a large diameter pipe, type water or gas, preferably the > same O.d as the seal you can tap it in with this using a heavy big hammer > or short-shaft sledgehammer. > > J. > > -- > Using Opera's revolutionary e-mail client:http://www.opera.com/mail/ |
#4
|
|||
|
|||
Tranny Input Shaft Seal Install Tool - Help Please!
> What kind of home made sleeve tool can I make that does not require
> welding to install the tranny input shaft seal? > > I was thinking of a flat washer just a little smaller diameter as the > input shaft seal and a short piece of pvc pipe and a rubber mallet. > > Thanks In Advance! > Any help will be appreciated! If you are talking about a type 1 transaxle, I've always been able to install it with a block of wood(short section of dowel rod is very nice) and a few light taps with a hammer. Or you can use the blunt end of a screwdriver and a hammer if you have a screwdriver that you don't particularly care if the tip gets damaged(read: craftsman screwdriver). PVC pipe would work as well, the idea is to not hit the seal so hard that you damage it, and make sure that you drive it in square with the bore. Chris |
#5
|
|||
|
|||
Tranny Input Shaft Seal Install Tool - Help Please!
On Aug 5, 11:49 am, wrote:
> The replacement input shaft seal does not have a metal outer edge. > Is it supposed to have one? > If so, where can I get one? > TIA No, the input shaft seal is just a rubber donut lip seal with a garter spring. I've never seen one with an outer edge made of metal. What vehicle are you working on? Chris |
#6
|
|||
|
|||
Tranny Input Shaft Seal Install Tool - Help Please!
> What vehicle are you working on?
It's a 1973 VW Beetle with a lowered compression 1600cc DP Type I engine and a stock transaxle. |
#7
|
|||
|
|||
Tranny Input Shaft Seal Install Tool - Help Please!
On Aug 6, 6:22*am, wrote:
> > What vehicle are you working on? > > It's a 1973 VW Beetle with a lowered compression 1600cc DP Type I > engine and a stock transaxle. The only transaxle seal that has a metal ring(technically a bushing) is the one that goes around the shift rod. It is actually two pieces, the piece with the rubber lip seal is driven into the nosecone from the outside. Is that the seal you are talking about? Chris |
#8
|
|||
|
|||
Tranny Input Shaft Seal Install Tool - Help Please!
I was referring to the input shaft seal in front of the clutch throw out bearing. Last night I looked through all of my manuals. In the last manual I looked at, the How to Keep Your Aircooled VW Alive by John Muir, it mentioned to be careful not to let the seal fall inside the transmission when you are trying to remove it. I think I've got a good idea of what to do now. Thanks again you all of you for your help. -------------------------- On Aug 6, 10:28 am, " > wrote: > On Aug 6, 6:22 am, wrote: > > > > What vehicle are you working on? > > > It's a 1973 VW Beetle with a lowered compression 1600cc DP Type I > > engine and a stock transaxle. > > The only transaxle seal that has a metal ring(technically a bushing) > is the one that goes around the shift rod. It is actually two pieces, > the piece with the rubber lip seal is driven into the nosecone from > the outside. Is that the seal you are talking about? > > Chris |
#9
|
|||
|
|||
Tranny Input Shaft Seal Install Tool - Help Please!
> wrote in message ... On Aug 6, 6:22 am, wrote: > > What vehicle are you working on? > > It's a 1973 VW Beetle with a lowered compression 1600cc DP Type I > engine and a stock transaxle. >The only transaxle seal that has a metal ring(technically a bushing) >is the one that goes around the shift rod. It is actually two pieces, >the piece with the rubber lip seal is driven into the nosecone from >the outside. Is that the seal you are talking about? Those capable of comprehending English read that his seal does not have a metal outer ring, and he questioned *if* it should.... Us readers also realize he is speaking of the input shaft seal based on his subject line and the description of where it went... For the OP I recommend a seal installation tool, and for the tool...I mean I recommend remedial reading courses. |
#10
|
|||
|
|||
Tranny Input Shaft Seal Install Tool - Help Please!
On Aug 5, 10:45*am, wrote:
> Hello! > What kind of home made sleeve tool can I make to install the tranny input shaft seal? Here's what I did. I used a tool similar to an ice pick to make about 5 little holes in the seal between the bore and the input shaft. All the little holes were close together. Then I stuck a flat blade screwdriver in the holes that sort of formed a slot. Then I levered out the seaI. I put a light coat of the orange Permatex rtv sealant on the outer diameter of the seal. I used a short piece of pcv pipe to gently drive in the new seal. It was a fairly simple job thanks to you guys. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
leaky A/C compressor shaft seal | Nathan Bates | General | 1 | March 25th 07 05:35 PM |
Axle Shaft Seal -- Fragile? | Dave[_29_] | Jeep | 3 | February 22nd 07 07:31 PM |
AWA [DEMAND] Lip Shaft Seal | [email protected] | General | 0 | April 11th 06 04:01 PM |
ax5 input shaft | jdarg | Jeep | 1 | July 4th 05 07:26 AM |
Left Transaxle Shaft Seal | Doug Samuel | Chrysler | 7 | June 3rd 05 12:59 PM |