A Cars forum. AutoBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AutoBanter forum » Auto makers » Chrysler
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

is the 3.5L 6 cyl 1994 LHS an interference engine?



 
 
Thread Tools Display Modes
  #11  
Old May 20th 06, 02:17 PM posted to rec.autos.makers.chrysler
external usenet poster
 
Posts: n/a
Default is the 3.5L 6 cyl 1994 LHS an interference engine?

In article >,
Bill Putney > wrote:

> aarcuda69062 wrote:
> > In article >,
> > Bill Putney > wrote:
> >
> >
> >>Is that true specifically of 94's?

> >
> >
> > Yes.
> >
> >
> >>I may have read discussions on this
> >>in the past in which it was concluded (at least by some) that certain
> >>years were iterference, others were not (even though the Gates guide
> >>shows them all as interfeence).

> >
> >
> > The Gates book has its share of errors.
> > (in this case, errors sell timing belts)
> >
> > I've replaced scores of these belts and not a one ever bent a
> > valve. That is more than a coincidence.
> >
> > My Mitchell On Demand lists the 3.5 as a non-interference engine,
> > it also lists the 3.2 as an interference engine. The Mitchell
> > text is direct from ChryCo.
> >
> > The engine has been out what, 13 years now, yet I have yet to see
> > anyone post a complaint of a 3.5 with bent valves in -any-
> > appropriate newsgroup, plenty of incidences posted for other
> > engines that -are- interference though.

>
> Apparently DC is schizophrenic on the point. You say Mitchell quotes
> Chryco as saying the 3.5 is non-interference. If that is correct (and
> applies to all years/versions), FWIW (apparently not much) my '99 LH-car
> FSM (on page 9-71 - 3.2/3.5 Engine Components - and page 9-100 - 'Timing
> Belt Removal') has bold text warnings: "NOTE The 3.2/3.5 are a NON
> [their emphasis] free-wheeling design" and "Caution: The 3.2/3.5L are
> NOT [their emphasis] freewheeling engines. Therefore care should be
> taken not to rotate the camshafts or crankshaft with the timing belt
> removed" respectively.
>
> As an added piece of confusion, there are several threads on the 300M
> Club forums where this question is discussed. Here's one of them:
> http://300mclub.org/forums/viewtopic...er=asc&star t =0
>
> ja300mes is a DC dealer tech and Red Baron is an ASE certified master
> mechanic and fleet manager and holds the 1/4 mile track record for
> normally aspirated 300M's - they both say it's interference (at least
> for 2nd gen cars). I'm not disagreeing with you - I've just seen
> convincing claims on both sides. I'm still wondering if there are maybe
> some year-to-year differences that may be causing at least some of the
> contradictory claims by apparently equally qualified people.


Dunno Bill.

The FSM lumps the 3.2 and 3.5 service information together,
perhaps they felt that a blanket statement about the engines
being interference would be easier for their mechanics to digest
than if they only called out the one that actually is.

My Gates guide lists all 3.5s as non-interference and I have yet
to see or hear of a crashed 3.5 due to a timing belt mishap, and
I have had them towed in with the belt wrapped around the
crankshaft pulley, they ran fine after repair.
Brother in-law works at the local Dodge dealership part dept, he
has never seen a 3.5 need the heads pulled because of a broken
timing belt.

It's also possible that the OEM belt supplier and myself are
wrong...
Ads
  #12  
Old May 20th 06, 02:40 PM posted to rec.autos.makers.chrysler
external usenet poster
 
Posts: n/a
Default is the 3.5L 6 cyl 1994 LHS an interference engine?

aarcuda69062 wrote:

> ...My Gates guide lists all 3.5s as non-interference...


Oh boy - more contradictions from one source. The on-line Gates T-belt
manual
(http://www.gates.com/downloads/downl...older=brochure)
shows all 3.5's as interference.

Bill Putney
(To reply by e-mail, replace the last letter of the alphabet in my
address with the letter 'x')
  #13  
Old May 20th 06, 04:10 PM posted to rec.autos.makers.chrysler
external usenet poster
 
Posts: n/a
Default is the 3.5L 6 cyl 1994 LHS an interference engine?

In article >,
Bill Putney > wrote:

> aarcuda69062 wrote:
>
> > ...My Gates guide lists all 3.5s as non-interference...

>
> Oh boy - more contradictions from one source. The on-line Gates T-belt
> manual
> (http://www.gates.com/downloads/downl...df&folder=broc
> hure)
> shows all 3.5's as interference.


Fun isn't it?

Gleaning accurate service information (even from the OEMs) is a
-big- issue in the industry.
  #14  
Old May 21st 06, 02:48 AM posted to rec.autos.makers.chrysler
external usenet poster
 
Posts: n/a
Default is the 3.5L 6 cyl 1994 LHS an interference engine?

When I owned my 94' LHS I bought the factory service manual. I also know a
tech who works for Chrysler and is factory trained. They both said that the
94' 3.5 engine was NON-INTERFERENCE. Yep, NON. They changed to a
interference engine in the next generation of 3.5 engine design. I read
that as a press release on Chryslers main page when the 300M was released.
That engine had 250hp (in HO trim). The original 3.5 was 215hp.

Steve M.....

"aarcuda69062" > wrote in message
...
> In article >,
> Bill Putney > wrote:
>
>> aarcuda69062 wrote:
>>
>> > ...My Gates guide lists all 3.5s as non-interference...

>>
>> Oh boy - more contradictions from one source. The on-line Gates T-belt
>> manual
>> (http://www.gates.com/downloads/downl...df&folder=broc
>> hure)
>> shows all 3.5's as interference.

>
> Fun isn't it?
>
> Gleaning accurate service information (even from the OEMs) is a
> -big- issue in the industry.



  #15  
Old May 22nd 06, 10:46 PM posted to rec.autos.makers.chrysler
external usenet poster
 
Posts: n/a
Default is the 3.5L 6 cyl 1994 LHS an interference engine?

Bill Putney wrote:

> random electron wrote:
>
>> Hi
>>
>> Does anyone know if the engine in a 1994 LHS is an interference engine
>> (aka crash motor)? It's a 3.5L 6 cyl.
>>
>> Thanks

>
>
> According to the Gates Timing Belt Replacement Guide
> (http://www.gates.com/brochure.cfm?br...cation_id=3487 -
> click the pdf link - give it time to download even if it acts like it's
> done), it *is* an interference engine.


Gates is wrong (actually, they're wrong an alarming amount of the time).
The first-gen 3.5 is very definitely a free-wheeling engine.

  #16  
Old May 22nd 06, 10:47 PM posted to rec.autos.makers.chrysler
external usenet poster
 
Posts: n/a
Default is the 3.5L 6 cyl 1994 LHS an interference engine?

maxpower wrote:

> "Bill Putney" > wrote in message
> ...
>
>>random electron wrote:
>>
>>
>>>Hi
>>>
>>>Does anyone know if the engine in a 1994 LHS is an interference engine

>
> (aka
>
>>>crash motor)? It's a 3.5L 6 cyl.
>>>
>>>Thanks

>>
>>According to the Gates Timing Belt Replacement Guide
>>(http://www.gates.com/brochure.cfm?br...cation_id=3487 -
>>click the pdf link - give it time to download even if it acts like it's
>>done), it *is* an interference engine.
>>
>>Bill Putney
>>(To reply by e-mail, replace the last letter of the alphabet in my
>>address with the letter 'x')

>
>
> It is an interference engine, that's why if you ever set up the timing marks
> at top dead center with the heads off you will see that the piston is not
> really at TDC. The reason behind that is because if the cam rotates while
> installing the belt the valve could slam into the piston and cause damage.
> The marks were offset to prevent this.
>


WRONG!!

This is not a second-generation (aluminum block) 3.5

It is an IRON BLOCK first-gen 3.5- no interference.

  #17  
Old May 22nd 06, 10:48 PM posted to rec.autos.makers.chrysler
external usenet poster
 
Posts: n/a
Default is the 3.5L 6 cyl 1994 LHS an interference engine?

Bill Putney wrote:

> Joe wrote:
>
>> "Bill Putney" > wrote in message
>> ...
>>
>>> random electron wrote:
>>>
>>>
>>>> Hi
>>>>
>>>> Does anyone know if the engine in a 1994 LHS is an interference
>>>> engine (aka crash motor)? It's a 3.5L 6 cyl.
>>>>
>>>> Thanks
>>>
>>>
>>> According to the Gates Timing Belt Replacement Guide
>>> (http://www.gates.com/brochure.cfm?br...cation_id=3487 -
>>> click the pdf link - give it time to download even if it acts like
>>> it's done), it *is* an interference engine.
>>>

>>
>> It's not. Just let folks that have broken their belts answer and that
>> way there's no confusion.

>
>
> Is that true specifically of 94's? I may have read discussions on this
> in the past in which it was concluded (at least by some) that certain
> years were iterference, others were not (even though the Gates guide
> shows them all as interfeence).


Only the aluminum-block 2nd-gen engine is *possibly* interference (and
I'm not SURE that it is). The first-gen iron-block engine (1993-1997) is
DEFINITELY NOT an interference engine.
  #18  
Old May 8th 17, 01:18 PM posted to rec.autos.makers.chrysler
robust two
external usenet poster
 
Posts: 1
Default is the 3.5L 6 cyl 1994 LHS an interference engine?

replying to Bill Putney, robust two wrote:
the timing belt went bust on my 1994 chrysler lhs what are the chances of
valves being bent? does it pays to take a chance?

--
for full context, visit http://www.motorsforum.com/chrysler/...ine-45950-.htm


 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
rec.autos.makers.chrysler FAQ, Part 1/6 Dr. David Zatz Chrysler 5 June 8th 05 05:28 AM
rec.autos.makers.chrysler FAQ, Part 1/6 Dr. David Zatz Chrysler 5 May 24th 05 05:27 AM
rec.autos.makers.chrysler FAQ, Part 1/6 Dr. David Zatz Chrysler 7 February 1st 05 02:43 PM
rec.autos.makers.chrysler FAQ, Part 1/6 Dr. David Zatz Chrysler 10 November 16th 04 06:28 AM
rec.autos.makers.chrysler FAQ, Part 1/6 Dr. David Zatz Chrysler 10 November 1st 04 06:24 AM


All times are GMT +1. The time now is 09:26 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AutoBanter.
The comments are property of their posters.