If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Rotor, without the 12 k-ohms resistance
... Distributor rotors, without 12,000 ohms resistance
1) The original Bosch rotors, as recommended by VW, I believe had 12,000 ohms, or was it 6,000 ohms of resistance across the contacts... that being from the centre, out to the tip. 2) What I am finding these days (probably from China) is just a straight through conductor with zero resistance. 3) Would love to hear feedback on what harm might come using these newer type rotors built without the resistance. 4) I am guessing/hoping it would not overheat the coil, since the proper Bosch coils have their own built-in resistance/ballast in the primary windings to control the proper amount of primary current in the primary windings... and thus control the proper level of current in the secondary, going through the rotor. Secondary current is always proportional to primary current, since that is the only place the secondary circuit can get its electrical energy. 5) So I am hoping some of you might have some thoughts on these newer rotors being found in the market missing the 12,000 ohms, or 6,000 ohms of resistance. 6) Hope Speedy Jim is still on his computer since I know anything electrical is definitely his specialty. Ross Virgin, Toronto, Canada ... |
#2
|
|||
|
|||
Rotor, without the 12 k-ohms resistance
rvirgin22 wrote:
> .. Distributor rotors, without 12,000 ohms resistance > > 1) The original Bosch rotors, as recommended by VW, I believe > had 12,000 ohms, or was it 6,000 ohms of resistance across the > contacts... that being from the centre, out to the tip. > > 2) What I am finding these days (probably from China) is just a > straight through conductor with zero resistance. > > 3) Would love to hear feedback on what harm might come using > these newer type rotors built without the resistance. > > 4) I am guessing/hoping it would not overheat the coil, since the > proper Bosch coils have their own built-in resistance/ballast in > the primary windings to control the proper amount of primary > current in the primary windings... and thus control the proper level > of current in the secondary, going through the rotor. Secondary > current is always proportional to primary current, since that is the > only place the secondary circuit can get its electrical energy. > > 5) So I am hoping some of you might have some thoughts on > these newer rotors being found in the market missing the > 12,000 ohms, or 6,000 ohms of resistance. > > 6) Hope Speedy Jim is still on his computer since I know anything > electrical is definitely his specialty. > > Ross Virgin, Toronto, Canada > .. Ross: Resistors were added some years back to help reduce ignition noise in car radios. There were resistor plugs and resistor wires and resistor rotors. Radio noise is much less a problem today and many feel that any resistance in the HI tension circuit degrades performance. That's probably why you're seeing rotors with the resistor omitted. Some discussion he http://www.shoptalkforums.com/viewto...=99137&start=0 Speedy Jim http://www.nls.net/mp/volks/ |
#3
|
|||
|
|||
Rotor, without the 12 k-ohms resistance
WOW, Speedy Jim, WOW Great response! That exactly explains why my old (AM)
Mororola Radio sounded so good years ago, staticy now. "Speedy Jim" > wrote in message ... > rvirgin22 wrote: >> .. Distributor rotors, without 12,000 ohms resistance >> >> 1) The original Bosch rotors, as recommended by VW, I believe >> had 12,000 ohms, or was it 6,000 ohms of resistance across the >> contacts... that being from the centre, out to the tip. >> >> 2) What I am finding these days (probably from China) is just a >> straight through conductor with zero resistance. >> >> 3) Would love to hear feedback on what harm might come using >> these newer type rotors built without the resistance. >> >> 4) I am guessing/hoping it would not overheat the coil, since the >> proper Bosch coils have their own built-in resistance/ballast in >> the primary windings to control the proper amount of primary >> current in the primary windings... and thus control the proper level >> of current in the secondary, going through the rotor. Secondary >> current is always proportional to primary current, since that is the >> only place the secondary circuit can get its electrical energy. >> >> 5) So I am hoping some of you might have some thoughts on >> these newer rotors being found in the market missing the >> 12,000 ohms, or 6,000 ohms of resistance. >> >> 6) Hope Speedy Jim is still on his computer since I know anything >> electrical is definitely his specialty. >> >> Ross Virgin, Toronto, Canada >> .. > > > Ross: > > Resistors were added some years back to help reduce ignition noise > in car radios. There were resistor plugs and resistor wires and > resistor rotors. > > Radio noise is much less a problem today and many feel that any > resistance in the HI tension circuit degrades performance. > That's probably why you're seeing rotors with the resistor omitted. > > Some discussion he > http://www.shoptalkforums.com/viewto...=99137&start=0 > > > > Speedy Jim > http://www.nls.net/mp/volks/ > |
#4
|
|||
|
|||
Rotor, without the 12 k-ohms resistance
rvirgin22 wrote:
> .. Distributor rotors, without 12,000 ohms resistance > > 1) The original Bosch rotors, as recommended by VW, I believe > had 12,000 ohms, or was it 6,000 ohms of resistance across the > contacts... that being from the centre, out to the tip. > > 2) What I am finding these days (probably from China) is just a > straight through conductor with zero resistance. > > 3) Would love to hear feedback on what harm might come using > these newer type rotors built without the resistance. --- <snipped> --- > > Ross Virgin, Toronto, Canada > .. The rotor that you think is from China sounds similar to a rotor that Aircooled.net discusses in the following link. It says that if you have a high output ignition, e.g. a CDI, you can dig out the resistor and braze a piece of brass in its place. They also sell modified resistor-less rotors. http://www.aircooled.net/new-bin/vie...GR0002&cartid= Under the drop down box that says "Required Selection" choose "Modified Rotor, SVDA ..." for a further explanation of how the rotor is modified. They sell the most commonly used stock rotors. I emailed them in 2004 with the request: "Do you sell a rotor that has had the resistor replaced for use with a CDI? My distributor uses a Bosch 04 006 rotor." Their answer was: "You'd have to order that rotor from us and have us modify it ($15 more). We normally carry the 04-033 or 04-038 rotors in modified form. John [Connolly]" You can send your technical questions to them by clicking on the "contact info" link at the bottom of every one of their web pages. -- Randall |
#5
|
|||
|
|||
Rotor, without the 12 k-ohms resistance
On Apr 12, 7:12*pm, rvirgin22 > wrote:
> .. * * Distributor rotors, without 12,000 ohms resistance > > 1) *The original Bosch rotors, as recommended by VW, I believe > had 12,000 ohms, or was it 6,000 ohms of resistance across the > contacts... that being from the centre, out to the tip. > > 2) *What I am finding these days (probably from China) is just a > straight through conductor with zero resistance. > > 3) *Would love to hear feedback on what harm might come using > these newer type rotors built without the resistance. > > 4) *I am guessing/hoping it would not overheat the coil, since the > proper Bosch coils have their own built-in resistance/ballast in > the primary windings to control the proper amount of primary > current in the primary windings... and thus control the proper level > of current in the secondary, going through the rotor. *Secondary > current is always proportional to primary current, since that is the > only place the secondary circuit can get its electrical energy. > > 5) *So I am hoping some of you might have some thoughts on > these newer rotors being found in the market missing the > 12,000 ohms, or 6,000 ohms of resistance. > > 6) *Hope Speedy Jim is still on his computer since I know anything > electrical is definitely his specialty. > > * * *Ross Virgin, Toronto, Canada > .. ... ... Speedy Jim and Randall 1) Much appreciate your informative replies. 2) If the resistance is just to stop radio interference, I definitely will not worry about that. Ross Virgin Toronto, Canada ... ... |
#6
|
|||
|
|||
Rotor, without the 12 k-ohms resistance
I would add that it is recommended that the resistor exist near the
arc (spark plug). So, the resistor spark plugs are the best location for a resistor to suppress radio interference. Giving up the resistor(s) in the rotor and plug wires then using resistor plugs would seem to provide the best radio noise suppression. Here's a good write up for anyone interested: http://www.oldcitypublishing.com/Ful...xt/Klimiec.pdf |
#7
|
|||
|
|||
Rotor, without the 12 k-ohms resistance
Did that on a 009 that had the resistor turn into a charred hole. Just dig
out enough space to allow a bit of wire to be soldered across as suggested then put a layer of araldite to hold it in place. John |
#8
|
|||
|
|||
Rotor, without the 12 k-ohms resistance
If you normally required a 5 kohm resistor and switch to a lower resistance rotor you may notice a slight difference in engine firing. Compare the spark produced by the 5 kohm resistor in the first trace to the traces for a 1 kohm resistor and one that has had the resistor removed (0 kohm). The 5 kohm trace has a very sharp fall from the peak voltage required to fire the spark plug, to the burn voltage level where the bulk of the current flows. This results in the longest burning spark. As the resistance of the rotor decreases, the length of time it takes to fall from peak voltage increases and the shorter the spark. Don't try to outsmart VW/Bosch: they knew what they are doing when they specified which rotor to use. |
#9
|
|||
|
|||
Rotor, without the 12 k-ohms resistance
Would have been interesting to see the CRO traces. With an
inductive/resistive circuit the time constant is L/R so decreasing R makes time constant greater which ties up with your results. I wonder how a 0 ohm rotor with 10K spark leads compare?. For years I constantly adjusted the chokes on my T3 carbies. After many years I eventually realised the best way to adjust them seemed to be how the VW service manual recommended!. I also agree with your last statement!!! John wrote in message ... If you normally required a 5 kohm resistor and switch to a lower resistance rotor you may notice a slight difference in engine firing. Compare the spark produced by the 5 kohm resistor in the first trace to the traces for a 1 kohm resistor and one that has had the resistor removed (0 kohm). The 5 kohm trace has a very sharp fall from the peak voltage required to fire the spark plug, to the burn voltage level where the bulk of the current flows. This results in the longest burning spark. As the resistance of the rotor decreases, the length of time it takes to fall from peak voltage increases and the shorter the spark. Don't try to outsmart VW/Bosch: they knew what they are doing when they specified which rotor to use. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Brand new rotor/pads - rotor scored | bellman | Technology | 6 | May 5th 06 09:00 PM |
99' Accord Brake Squeak - just replaced brakes, rotor and rotor again | [email protected] | Honda | 7 | July 21st 05 03:15 AM |
Anyone know whats kinda ohms reading I should be getting from a good coil?(91 jetta) | gutlessjetta | VW water cooled | 1 | July 5th 05 04:47 PM |
HELP!!! Cig. Lighter: 9 ohms between POS and GROUND???? | Thomas G. Marshall | Honda | 24 | October 27th 04 03:06 AM |
Early C3: 4 X 6 Delco replacement speakers - 10 Ohms or not? | pgtr | Corvette | 2 | August 22nd 04 04:12 AM |