If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
tunnel to pan connection
Hi all
Just got a 72 regular beetle and am evaluating what needs to be done. It will need floors, heater channels and one of the door post bottoms will need to be reconstructed. The engine/tranny is in very good shape. Along the tunnel a lip exists that one normally welds the floor pans to. On mine, there's a gap between this lip and the tunnel. Is this lip part of a plate that's welded along the bottom of the tunnel? Or is it something welded along the edge of the tunnel? It looks like a plate, but can't tell until I get under the car and haven't done that yet. Could I "just" (after taking the body off, that is) flip the frame and weld a new bottom plate back on? Thanks! Remco |
Ads |
#2
|
|||
|
|||
"Remco" > wrote in message
oups.com... > Hi all > Just got a 72 regular beetle and am evaluating what needs to be done. > > It will need floors, heater channels and one of the door post bottoms > will need to be reconstructed. Throw it away. Find a better start. Don't waste your time and money on it. |
#3
|
|||
|
|||
Yeah, and he didn't ask about if he should throw it away eh? Admittedly his obviously will require some dedication but
that doesn't mean he should be told to just automatically throw it away. "johnboy" > wrote in message ... > "Remco" > wrote in message > oups.com... > > Hi all > > Just got a 72 regular beetle and am evaluating what needs to be done. > > > > It will need floors, heater channels and one of the door post bottoms > > will need to be reconstructed. > > Throw it away. Find a better start. Don't waste your time and money on it. > > |
#4
|
|||
|
|||
"Remco" > wrote in message > On mine, there's a gap between this lip and the tunnel. Is this lip > part of a plate that's welded along the bottom of the tunnel? Or is it > something welded along the edge of the tunnel? > the "tunnel" or "spine" is a two piece unit through the car...the upside down "U" shaped part is welded to the bottom plate...there should be no gap...the bottom plate is, as you speculated, wider than the upside down "U" shaped part so the pans can be attatched to it....sounds like you have a project ahead of you, but honestly rust repair is easier than collision repair, so if the car is, so they say, "straight" you will be okay....you seem to have a good attitude, so go for it.... |
#5
|
|||
|
|||
"Joey Tribiani" > wrote in message
news:6Yrpe.68961$sy6.52416@lakeread04... > > "Remco" > wrote in message > > > On mine, there's a gap between this lip and the tunnel. Is this lip > > part of a plate that's welded along the bottom of the tunnel? Or is it > > something welded along the edge of the tunnel? > > > > the "tunnel" or "spine" is a two piece unit through the car...the upside > down "U" shaped part is welded to the bottom plate...there should be no > gap...the bottom plate is, as you speculated, wider than the upside down "U" > shaped part so the pans can be attatched to it....sounds like you have a > project ahead of you, but honestly rust repair is easier than collision > repair, so if the car is, so they say, "straight" you will be okay....you > seem to have a good attitude, so go for it.... > Thanks, Joey - That's the reply I was looking for. |
#6
|
|||
|
|||
"remco" > wrote in message news:E5spe.23055 > Thanks, Joey - That's the reply I was looking for. > > you are welcome...shall i begin cussing now? LOL |
#7
|
|||
|
|||
"Joey Tribiani" > wrote in message
news:flspe.68967$sy6.45422@lakeread04... > > "remco" > wrote in message news:E5spe.23055 > > > Thanks, Joey - That's the reply I was looking for. > > > > > > you are welcome...shall i begin cussing now? LOL > Please do -- you might get a cramp if you don't.. |
#8
|
|||
|
|||
"remco" > wrote in message news:u3tpe.66969 >> > Please do -- you might get a cramp if you don't.. > > > or i might explode..... |
#9
|
|||
|
|||
On Wed, 8 Jun 2005 00:23:49 -0400, "Joey Tribiani" >
wrote: > >"remco" > wrote in message news:u3tpe.66969 > >>> >> Please do -- you might get a cramp if you don't.. >> >> >> > >or i might explode..... > Then maybe you should "let it go." hahaha! |
#10
|
|||
|
|||
"Shag" > wrote in message ... >> >>or i might explode..... >> > > Then maybe you should "let it go." hahaha! > hehe...quick on your feet...."good one".....or something... |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Connect telephone showing "connection not available" | Arnoud Reininga | Alfa Romeo | 2 | February 22nd 05 08:10 PM |
DaimlerChrysler offices searched in connection with sale of vehicles toIran | MoPar Man | Chrysler | 2 | December 11th 04 10:13 PM |
When You Hear The Heavy Accent & The Poor Phone Connection... HANG UP!! ----- Cxb2gmH9xB | Geoff Wood | 4x4 | 0 | March 30th 04 09:26 AM |