If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Oil Pan bolts?
I'm in the process of removing the oil pan from my '75 CJ5 258. I've read
through my Chilton's and Haynes manual, but can't seem to find the Torque spec's for the oil pan retaining bolts. The spec's for the 4 cylinder is in the Chilton's, but not the Haynes. Please Help. Also, any recommendations for oil pumps on this engine? -- Thanks Always !!! Paul '75 CJ5 258 Vail, CO. |
Ads |
#2
|
|||
|
|||
Hi Paul,
Hold the head of your quarter inch ratchet between your thumb and fore fingers, and twist about five pounds of torque, anything more will split the gasket: http://members.tripod.com/torquespec...-86_st6eng.htm God Bless America, ßill O|||||||O http://www.billhughes.com/ Paul Brogren wrote: > > I'm in the process of removing the oil pan from my '75 CJ5 258. I've read > through my Chilton's and Haynes manual, but can't seem to find the Torque > spec's for the oil pan retaining bolts. The spec's for the 4 cylinder is in > the Chilton's, but not the Haynes. Please Help. Also, any recommendations > for oil pumps on this engine? > > -- > Thanks Always !!! > Paul '75 CJ5 258 > Vail, CO. |
#3
|
|||
|
|||
Paul Brogren ) wrote on Monday 17 January 2005 02:15 pm:
> I'm in the process of removing the oil pan from my '75 CJ5 258. I've read > through my Chilton's and Haynes manual, but can't seem to find the Torque > spec's for the oil pan retaining bolts. The spec's for the 4 cylinder is > in > the Chilton's, but not the Haynes. Please Help. Also, any > recommendations for oil pumps on this engine? > From my '82 service manual, the 1/4" are 7 ft-lb, and the 5/16" are 11 ft-lb. Use a torque wrench that is calibrated in inch-lbs. -- Michael White "To protect people from the effects of folly is to fill the world with fools." -Herbert Spencer, 1891 |
#4
|
|||
|
|||
Yeah, I thought I'd need an inch pound wrench sooner or later. Thanks again
for the advice. let me know about the high volume oil pumps vs. the standard ones. I need to order one in the next couple days. -- Thanks Always !!! Paul '75 CJ5 258 Vail, CO. "Michael White" > wrote in message ink.net... > Paul Brogren ) wrote on Monday 17 January 2005 02:15 pm: > > > I'm in the process of removing the oil pan from my '75 CJ5 258. I've read > > through my Chilton's and Haynes manual, but can't seem to find the Torque > > spec's for the oil pan retaining bolts. The spec's for the 4 cylinder is > > in > > the Chilton's, but not the Haynes. Please Help. Also, any > > recommendations for oil pumps on this engine? > > > > From my '82 service manual, the 1/4" are 7 ft-lb, and the 5/16" are 11 > ft-lb. Use a torque wrench that is calibrated in inch-lbs. > -- > Michael White "To protect people from the effects of folly is to > fill the world with fools." -Herbert Spencer, 1891 |
#5
|
|||
|
|||
My Haynes manual has them listed in foot pounds, not inch pounds and
says the small 1/4" ones are 5 to 7 Foot lb. and the larger 5/16" ones are 10 to 13 foot lb. That is on page 2C-5. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Paul Brogren wrote: > > I'm in the process of removing the oil pan from my '75 CJ5 258. I've read > through my Chilton's and Haynes manual, but can't seem to find the Torque > spec's for the oil pan retaining bolts. The spec's for the 4 cylinder is in > the Chilton's, but not the Haynes. Please Help. Also, any recommendations > for oil pumps on this engine? > > -- > Thanks Always !!! > Paul '75 CJ5 258 > Vail, CO. |
#6
|
|||
|
|||
There are two specs, one for 1/4" screws and another for 5/16" screws.
The Set To spec is 7 ft lb for the 1/4, and 11 for the 5/16. The Service In Use spec is 5 to 9 and 9 to 13, respectively. All measurments are in foot pounds. The spec for Oil Pressure is 13psi at 600 RPM and 37 to 75 psi from 1600 RPM and up. The max pressure is determined by a bypass valve, this pressure is capped at 75psi. I am not sure that a high flow oil pump is beneficial unless you make other unknown changes to accomodate the increased flow/pressure. My inclination would be to get another stock pump. I pulled this data from my Factory Service Manual, but I must give a caveat that the Oil Capacity is listed at 4 quarts, plus the filter. My 258 holds 6 quarts, including the filter, so I can not vouch for the accuracy of the information I have given. Having said that, If I was rebuilding my motor, I would use all of the information, and accept the idea that the oil capacity is shown incorrectly. "Paul Brogren" > wrote in message ... > I'm in the process of removing the oil pan from my '75 CJ5 258. I've read > through my Chilton's and Haynes manual, but can't seem to find the Torque > spec's for the oil pan retaining bolts. The spec's for the 4 cylinder is > in > the Chilton's, but not the Haynes. Please Help. Also, any > recommendations > for oil pumps on this engine? > > -- > Thanks Always !!! > Paul '75 CJ5 258 > Vail, CO. > > |
#7
|
|||
|
|||
"Michael White" > wrote in message ink.net... > Paul Brogren ) wrote on Monday 17 January 2005 02:15 pm: > >> I'm in the process of removing the oil pan from my '75 CJ5 258. I've >> read >> through my Chilton's and Haynes manual, but can't seem to find the Torque >> spec's for the oil pan retaining bolts. The spec's for the 4 cylinder is >> in >> the Chilton's, but not the Haynes. Please Help. Also, any >> recommendations for oil pumps on this engine? >> > > From my '82 service manual, the 1/4" are 7 ft-lb, and the 5/16" are 11 > ft-lb. Use a torque wrench that is calibrated in inch-lbs. My '81 FSM has the same specs. But, how does one measure a foot pound spec with an inch pound torque wrench? If one was supposed to use an inch pound wrench, wouldn't the spec be 84 and 132 in lb, respectively? And, does an inch pound wrench go this high? I might do this wrong, but I would use a foot pound wrench when the spec calls for foot pounds. The trouble I would run into is that my foot pound wrench goes so high that is might not be very accurate at these small numbers. |
#8
|
|||
|
|||
On Tue, 18 Jan 2005 09:17:39 -0800, Jeff Strickland wrote:
> But, how does one measure a foot pound spec with an inch pound > torque wrench? Convert the units. > If one was supposed to use an inch pound > wrench, wouldn't the spec be 84 and 132 in lb, respectively? That depends on the author/publisher of the publication you are reading. > And, does an inch pound wrench go this high? Yes. http://www.sears.com/sr/javasr/produ...orque+Wrenches > I might do this wrong, but I would use a foot pound wrench when the spec > calls for foot pounds. The trouble I would run into is that my foot pound > wrench goes so high that is might not be very accurate at these small > numbers. Exactly -- the wrench calibrated for inch-pounds will be more accurate and therefore would be a better choice of tool. In fact, the wrench I have doesn't go low enough for some of those bolts listed : http://www.sears.com/sr/javasr/produ...orque+Wrenches -D -- \begin{humor} Disclaimer: If I receive a message from you, you are agreeing that: 1. I am by definition, "the intended recipient" 2. All information in the email is mine to do with as I see fit and make such financial profit, political mileage, or good joke as it lends itself to. In particular, I may quote it on USENET or the WWW. 3. I may take the contents as representing the views of your company. 4. This overrides any disclaimer or statement of confidentiality that may be included on your message \end{humor} www: http://dman13.dyndns.org/~dman/ jabber: |
#9
|
|||
|
|||
Okay, I got some pretty decent info today. I talked to one of senior
mechanics that I know from our Public Works Fleet Maintenance dept. He said to do a visual pressure test. I agree it will take a keen eye, but he said once the bolts are just finger tight, turn each bolt just until one sees a very slight visual gasket pinch. He said it works great. You just have to barely see the gasket squish and you stop. -- Thanks Always !!! Paul '75 CJ5 258 Vail, CO. "Jeff Strickland" > wrote in message ... > There are two specs, one for 1/4" screws and another for 5/16" screws. > > The Set To spec is 7 ft lb for the 1/4, and 11 for the 5/16. The Service In > Use spec is 5 to 9 and 9 to 13, respectively. All measurments are in foot > pounds. > > > The spec for Oil Pressure is 13psi at 600 RPM and 37 to 75 psi from 1600 RPM > and up. The max pressure is determined by a bypass valve, this pressure is > capped at 75psi. > > I am not sure that a high flow oil pump is beneficial unless you make other > unknown changes to accomodate the increased flow/pressure. My inclination > would be to get another stock pump. > > > I pulled this data from my Factory Service Manual, but I must give a caveat > that the Oil Capacity is listed at 4 quarts, plus the filter. My 258 holds 6 > quarts, including the filter, so I can not vouch for the accuracy of the > information I have given. Having said that, If I was rebuilding my motor, I > would use all of the information, and accept the idea that the oil capacity > is shown incorrectly. > > > > > > "Paul Brogren" > wrote in message > ... > > I'm in the process of removing the oil pan from my '75 CJ5 258. I've read > > through my Chilton's and Haynes manual, but can't seem to find the Torque > > spec's for the oil pan retaining bolts. The spec's for the 4 cylinder is > > in > > the Chilton's, but not the Haynes. Please Help. Also, any > > recommendations > > for oil pumps on this engine? > > > > -- > > Thanks Always !!! > > Paul '75 CJ5 258 > > Vail, CO. > > > > > > |
#10
|
|||
|
|||
Perfect.
God Bless America, ßill O|||||||O http://www.billhughes.com/ Paul Brogren wrote: > > Okay, I got some pretty decent info today. I talked to one of senior > mechanics that I know from our Public Works Fleet Maintenance dept. He said > to do a visual pressure test. I agree it will take a keen eye, but he said > once the bolts are just finger tight, turn each bolt just until one sees a > very slight visual gasket pinch. He said it works great. You just have to > barely see the gasket squish and you stop. > > -- > Thanks Always !!! > Paul '75 CJ5 258 > Vail, CO. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Wheel bolts instead of lug nuts...why? | GRL | BMW | 52 | January 9th 05 09:17 PM |
Socket For Loosening Caliper Bolts On 2000 Audi A4? | Don Christine | Audi | 3 | August 31st 04 11:22 PM |
Source for Odd Bolts | Harry Potter | Antique cars | 0 | October 13th 03 12:13 AM |