"Dad" > wrote in message
.. .
>
> "uncle_vito" > wrote in message
> ...
>>
>> "Dad" > wrote in message
>> .. .
>>>
>>> "uncle_vito" > wrote in message
>>> ...
>>>>
>>>> "Dad" > wrote in message
>>>> .. .
>>>>>
>>>>> Why do you need an electric cloth top? On the other had I do like the
>>>>> hard (soft) top on the SC300, looks sharp. Actually the convertible
>>>>> looks much better than the coupe and for some reason it does not show
>>>>> all the add on scoops/vents.
>>>>>
>>>>> Still lust after its VVT and DI in a push rod engine. Just a few
>>>>> reasons and the first is the amount of sensors on the DOHC with VVT
>>>>> and DI, each head gets 4 camshaft sensors and cam position sensor
>>>>> actuator and all the wires for same. Plus all the added bolts and
>>>>> screws to just hold it together. Eighteen for the DOHC and 4 for the
>>>>> push rod valve covers. Now lets talk timing chains, one for the old
>>>>> pushrod and three for the DOHC, 9 sprockets in place of 2 and the
>>>>> worst part is well over 400 link pins to wear on 3 chains with 16
>>>>> timing marks versus one. All that to get rid of the 16 push rods. Plus
>>>>> the engine gets less MPG than my old school C6 with none of that crap.
>>>>> The only thing I like about the DOHC is the red line, sounds good at
>>>>> 7,000 but not worth the cost.
>>>>
>>>>
>>>> But the Toyota V-8 is an engineering work of art that does not develop
>>>> valve float at high RPM nor needs cam destroying spring pressures to do
>>>> it. Just as well that GM sticks to OHV engines. With the
>>>> 'complexity' of DOHC, the C7 would never be out of the shop.
>>> By the time valve float would happen, which it don't when computer
>>> controlled, your Toy would be two counties behind. Sorry, try again.
>>>
>>> Just to let you in on where I'm coming from I drive what I'm talking
>>> about. How about you?
>>>
>>>
>>
>> I drive a Toyota Highlander and BMW 3 series. The DOHC VVT 6s in those
>> have absolutely NO problems. BMW is known for its smooth 6's. I have
>> the 2.5L and it revs like crazy and gets great mileage. Need to use
>> premium but at the mileage it gets, I do not care.
>>
>> Sorry, not interested in any DOHC that GM offers. The GM pencil pushers
>> that run the company only produced DOHC engines as a 'me too' to its
>> competition.
>>
>> You seem plenty knowledgeable, Dad. You should go up against Hib
>> Halverson. Except Hib is an arrogant ass.
>>
> Already called him on a couple of mistakes, he is a blow hard and sadly
> represent some of the owners that like to spend money and brag about it
> and owning a Corvette. He does have knowledge I don't but if you call him
> out he just hides and don't reply like he didn't even notice what was
> said.
>
> Myself I like to know what I'm driving and what it can do but could care
> less what someone else drives and see no reason to cut them down for their
> choice. Which brings me to your statement that the "C7 wouldn't get out of
> the shop". What does that mean except you would like to knock something
> you know nothing about. I haven't seen or heard of any "cam destroying
> spring pressure" from any cars for decades. Ever hear of roller rockers?
> Back in the 70's when GM built the V8s with the hot centers there were
> lots of cam failures but it was not from spring pressure it was carbon ash
> that ground down the lobes.
>
> My oldest son drives a Toy pickup and he couldn't get close to the mileage
> I did on my Chevy van that was 800 pounds heavier. His Odyssey is about 5
> MPG short also. Poor old push rod V6 just never knew when to stop on a
> tank of gas. When I had the Northstar in my STS it soured me on the
> overhead cam with it's bad gas mileage. The DOHC I have now is about 6
> mile per gallon short of my C6 but it does burn regular.
>
> By the way he lives about 20 miles from the BMW plant/museum in Greer S.C.
> and if you ever get there it is a treat to see. If possible take the plant
> tour, sporadic availability but worth the time if it works out.
>
>
>

To my knowledge, Hib never had any money because he could never keep a job.
He always knew more than his boss. Perhaps in his older years he has
inherited/married into wealth.

Well no one knows about the reliablilty of the C7 since it has not gone into
production. I am just going by GM's history of problems with the first
model year. To think someone was dumb enough to pay $1M for the first C7.
Is this the car that all the assemblers learned on? If not, then it was
not really the first C7. If they build and practice on cars 1-9 and then
destroy them does that make #10 the first car built?