AutoBanter

AutoBanter (http://www.autobanter.com/index.php)
-   Chrysler (http://www.autobanter.com/forumdisplay.php?f=10)
-   -   98 Intrepid oil light flickers at idle when engine hot (http://www.autobanter.com/showthread.php?t=8964)

Dan Brenner November 28th 04 11:03 PM

98 Intrepid oil light flickers at idle when engine hot
 
I have read there is a TSB (08-36-99) on this problem that I have been
experiencing lately. I have purchased the wire terminal/vent p/n
05017800AA mentioned in the TSB and I want to install it myself.
I would like to know the location of the oil pressure switch on the
2.7L engine. I have looked under the engine (passenger's side) and I
see 3 units. From the firewall towards the front of the car they a
a black one, an orange one and a green one (these are the connectors'
colors). I suspect the green one is the oil pressure switch but I'm
not sure. If it is the one, how do I remove the switch connector from
the switch? Something seems to lock it in place and I can't see the
typical plastic tabs.
If anyone has experience with this could you please share it.
Thanks much,
Dan

Greg Houston November 30th 04 02:50 AM

Dan Brenner wrote:

> I have read there is a TSB (08-36-99) on this problem that I have been
> experiencing lately. I have purchased the wire terminal/vent p/n
> 05017800AA mentioned in the TSB and I want to install it myself.
> I would like to know the location of the oil pressure switch on the
> 2.7L engine. I have looked under the engine (passenger's side) and I
> see 3 units. From the firewall towards the front of the car they a
> a black one, an orange one and a green one (these are the connectors'
> colors). I suspect the green one is the oil pressure switch but I'm
> not sure. If it is the one, how do I remove the switch connector from
> the switch? Something seems to lock it in place and I can't see the
> typical plastic tabs.
> If anyone has experience with this could you please share it.
> Thanks much,
> Dan


I am not sure about the location of the oil pressure switch on your
engine, but it is a green fitting adjacent to the oil filter on the 3.2L
engine. There is probably a place to press the connector to remove it.
Here is the TSB you are referring to; consult the factory service manual
for more information with graphics.

Technical Service Bulletin 08-36-99

SUBJECT: Engine Oil Pressure Light Flicker

OVERVIEW: This bulletin involves adding a
terminal/wire/vent to the oil pressure switch
connector.

MODELS:
1998-1999 (LH) Concorde/Intrepid

NOTE: This bulletin applies to vehicles equipped with
a 2.7L engine

SYMPTOM/CONDITION:
With a hot engine the oil pressure light may be on or
flicker on at idle.

DIAGNOSIS:
Verify engine oil pressure as described on page 9-21
of the 1999 Concorde/Intrepid/LHS/300M service manual.
If engine oil pressure is withing specification
perform the Repair Procedure.

PARTS REQUIRED:

1 05017800AA Wire Terminal/Vent

REPAIR PROCEDU
1. Raise vehicle on suitable hoist.
2. Remove engine oil pressure switch connector from
switch.
3.) Remove sealing dart from the empty cavity at the
rear of the connector.
4.) Pull terminal locking ring outward from front (switch)
side of connector to gain access to terminal locking tabs.
5.) Install wire terminal/vent, p/n 05017800AA, in place
of the removed sealing dart. Slide locking ring back
into place.
6.) Attach the connector back on the oil pressure switch.
7.) Spot tape the wire/vent to follow the harness towards
the top of the engine compartment.

POLICY: Reimbursable within the provisions of the warranty.

TIME ALLOWANCE:
Labor Operation No: 08-90-65-96 .................. 0.2 Hrs.

FAILURE CODE: P8 - New Part

Form TSB-003 Rev. 1.07



Greg Houston November 30th 04 02:50 AM

Dan Brenner wrote:

> I have read there is a TSB (08-36-99) on this problem that I have been
> experiencing lately. I have purchased the wire terminal/vent p/n
> 05017800AA mentioned in the TSB and I want to install it myself.
> I would like to know the location of the oil pressure switch on the
> 2.7L engine. I have looked under the engine (passenger's side) and I
> see 3 units. From the firewall towards the front of the car they a
> a black one, an orange one and a green one (these are the connectors'
> colors). I suspect the green one is the oil pressure switch but I'm
> not sure. If it is the one, how do I remove the switch connector from
> the switch? Something seems to lock it in place and I can't see the
> typical plastic tabs.
> If anyone has experience with this could you please share it.
> Thanks much,
> Dan


I am not sure about the location of the oil pressure switch on your
engine, but it is a green fitting adjacent to the oil filter on the 3.2L
engine. There is probably a place to press the connector to remove it.
Here is the TSB you are referring to; consult the factory service manual
for more information with graphics.

Technical Service Bulletin 08-36-99

SUBJECT: Engine Oil Pressure Light Flicker

OVERVIEW: This bulletin involves adding a
terminal/wire/vent to the oil pressure switch
connector.

MODELS:
1998-1999 (LH) Concorde/Intrepid

NOTE: This bulletin applies to vehicles equipped with
a 2.7L engine

SYMPTOM/CONDITION:
With a hot engine the oil pressure light may be on or
flicker on at idle.

DIAGNOSIS:
Verify engine oil pressure as described on page 9-21
of the 1999 Concorde/Intrepid/LHS/300M service manual.
If engine oil pressure is withing specification
perform the Repair Procedure.

PARTS REQUIRED:

1 05017800AA Wire Terminal/Vent

REPAIR PROCEDU
1. Raise vehicle on suitable hoist.
2. Remove engine oil pressure switch connector from
switch.
3.) Remove sealing dart from the empty cavity at the
rear of the connector.
4.) Pull terminal locking ring outward from front (switch)
side of connector to gain access to terminal locking tabs.
5.) Install wire terminal/vent, p/n 05017800AA, in place
of the removed sealing dart. Slide locking ring back
into place.
6.) Attach the connector back on the oil pressure switch.
7.) Spot tape the wire/vent to follow the harness towards
the top of the engine compartment.

POLICY: Reimbursable within the provisions of the warranty.

TIME ALLOWANCE:
Labor Operation No: 08-90-65-96 .................. 0.2 Hrs.

FAILURE CODE: P8 - New Part

Form TSB-003 Rev. 1.07



Arthur November 30th 04 03:34 PM

Out of warranty?? That'll be $125, please. Oh, and please help yourself to
a complimentary cup of day old coffee while you wait all day for your car.

"Greg Houston" > wrote in message
...
> Dan Brenner wrote:
>
>> I have read there is a TSB (08-36-99) on this problem that I have been
>> experiencing lately. I have purchased the wire terminal/vent p/n
>> 05017800AA mentioned in the TSB and I want to install it myself.
>> I would like to know the location of the oil pressure switch on the
>> 2.7L engine. I have looked under the engine (passenger's side) and I
>> see 3 units. From the firewall towards the front of the car they a
>> a black one, an orange one and a green one (these are the connectors'
>> colors). I suspect the green one is the oil pressure switch but I'm
>> not sure. If it is the one, how do I remove the switch connector from
>> the switch? Something seems to lock it in place and I can't see the
>> typical plastic tabs.
>> If anyone has experience with this could you please share it.
>> Thanks much,
>> Dan

>
> I am not sure about the location of the oil pressure switch on your
> engine, but it is a green fitting adjacent to the oil filter on the 3.2L
> engine. There is probably a place to press the connector to remove it.
> Here is the TSB you are referring to; consult the factory service manual
> for more information with graphics.
>
> Technical Service Bulletin 08-36-99
>
> SUBJECT: Engine Oil Pressure Light Flicker
>
> OVERVIEW: This bulletin involves adding a
> terminal/wire/vent to the oil pressure switch
> connector.
>
> MODELS:
> 1998-1999 (LH) Concorde/Intrepid
>
> NOTE: This bulletin applies to vehicles equipped with
> a 2.7L engine
>
> SYMPTOM/CONDITION:
> With a hot engine the oil pressure light may be on or
> flicker on at idle.
>
> DIAGNOSIS:
> Verify engine oil pressure as described on page 9-21
> of the 1999 Concorde/Intrepid/LHS/300M service manual.
> If engine oil pressure is withing specification
> perform the Repair Procedure.
>
> PARTS REQUIRED:
>
> 1 05017800AA Wire Terminal/Vent
>
> REPAIR PROCEDU
> 1. Raise vehicle on suitable hoist.
> 2. Remove engine oil pressure switch connector from
> switch.
> 3.) Remove sealing dart from the empty cavity at the
> rear of the connector.
> 4.) Pull terminal locking ring outward from front (switch)
> side of connector to gain access to terminal locking tabs.
> 5.) Install wire terminal/vent, p/n 05017800AA, in place
> of the removed sealing dart. Slide locking ring back
> into place.
> 6.) Attach the connector back on the oil pressure switch.
> 7.) Spot tape the wire/vent to follow the harness towards
> the top of the engine compartment.
>
> POLICY: Reimbursable within the provisions of the warranty.
>
> TIME ALLOWANCE:
> Labor Operation No: 08-90-65-96 .................. 0.2 Hrs.
>
> FAILURE CODE: P8 - New Part
>
> Form TSB-003 Rev. 1.07
>
>




Arthur November 30th 04 03:34 PM

Out of warranty?? That'll be $125, please. Oh, and please help yourself to
a complimentary cup of day old coffee while you wait all day for your car.

"Greg Houston" > wrote in message
...
> Dan Brenner wrote:
>
>> I have read there is a TSB (08-36-99) on this problem that I have been
>> experiencing lately. I have purchased the wire terminal/vent p/n
>> 05017800AA mentioned in the TSB and I want to install it myself.
>> I would like to know the location of the oil pressure switch on the
>> 2.7L engine. I have looked under the engine (passenger's side) and I
>> see 3 units. From the firewall towards the front of the car they a
>> a black one, an orange one and a green one (these are the connectors'
>> colors). I suspect the green one is the oil pressure switch but I'm
>> not sure. If it is the one, how do I remove the switch connector from
>> the switch? Something seems to lock it in place and I can't see the
>> typical plastic tabs.
>> If anyone has experience with this could you please share it.
>> Thanks much,
>> Dan

>
> I am not sure about the location of the oil pressure switch on your
> engine, but it is a green fitting adjacent to the oil filter on the 3.2L
> engine. There is probably a place to press the connector to remove it.
> Here is the TSB you are referring to; consult the factory service manual
> for more information with graphics.
>
> Technical Service Bulletin 08-36-99
>
> SUBJECT: Engine Oil Pressure Light Flicker
>
> OVERVIEW: This bulletin involves adding a
> terminal/wire/vent to the oil pressure switch
> connector.
>
> MODELS:
> 1998-1999 (LH) Concorde/Intrepid
>
> NOTE: This bulletin applies to vehicles equipped with
> a 2.7L engine
>
> SYMPTOM/CONDITION:
> With a hot engine the oil pressure light may be on or
> flicker on at idle.
>
> DIAGNOSIS:
> Verify engine oil pressure as described on page 9-21
> of the 1999 Concorde/Intrepid/LHS/300M service manual.
> If engine oil pressure is withing specification
> perform the Repair Procedure.
>
> PARTS REQUIRED:
>
> 1 05017800AA Wire Terminal/Vent
>
> REPAIR PROCEDU
> 1. Raise vehicle on suitable hoist.
> 2. Remove engine oil pressure switch connector from
> switch.
> 3.) Remove sealing dart from the empty cavity at the
> rear of the connector.
> 4.) Pull terminal locking ring outward from front (switch)
> side of connector to gain access to terminal locking tabs.
> 5.) Install wire terminal/vent, p/n 05017800AA, in place
> of the removed sealing dart. Slide locking ring back
> into place.
> 6.) Attach the connector back on the oil pressure switch.
> 7.) Spot tape the wire/vent to follow the harness towards
> the top of the engine compartment.
>
> POLICY: Reimbursable within the provisions of the warranty.
>
> TIME ALLOWANCE:
> Labor Operation No: 08-90-65-96 .................. 0.2 Hrs.
>
> FAILURE CODE: P8 - New Part
>
> Form TSB-003 Rev. 1.07
>
>




Mike Behnke November 30th 04 04:03 PM

Dan;

Oil pressure switch connector body is light green in color. 1 wire
coming out of it. With the engine off, that wire should be grounded to
the chassis. Lock tab is probably facing away from you.


The crank shaft position sensor connector body is black. Don't know
off-hand what the orange connector is.


Dan Brenner wrote:

> I have read there is a TSB (08-36-99) on this problem that I have been
> experiencing lately. I have purchased the wire terminal/vent p/n
> 05017800AA mentioned in the TSB and I want to install it myself.
> I would like to know the location of the oil pressure switch on the
> 2.7L engine. I have looked under the engine (passenger's side) and I
> see 3 units. From the firewall towards the front of the car they a
> a black one, an orange one and a green one (these are the connectors'
> colors). I suspect the green one is the oil pressure switch but I'm
> not sure. If it is the one, how do I remove the switch connector from
> the switch? Something seems to lock it in place and I can't see the
> typical plastic tabs.
> If anyone has experience with this could you please share it.
> Thanks much,
> Dan


Mike Behnke November 30th 04 04:03 PM

Dan;

Oil pressure switch connector body is light green in color. 1 wire
coming out of it. With the engine off, that wire should be grounded to
the chassis. Lock tab is probably facing away from you.


The crank shaft position sensor connector body is black. Don't know
off-hand what the orange connector is.


Dan Brenner wrote:

> I have read there is a TSB (08-36-99) on this problem that I have been
> experiencing lately. I have purchased the wire terminal/vent p/n
> 05017800AA mentioned in the TSB and I want to install it myself.
> I would like to know the location of the oil pressure switch on the
> 2.7L engine. I have looked under the engine (passenger's side) and I
> see 3 units. From the firewall towards the front of the car they a
> a black one, an orange one and a green one (these are the connectors'
> colors). I suspect the green one is the oil pressure switch but I'm
> not sure. If it is the one, how do I remove the switch connector from
> the switch? Something seems to lock it in place and I can't see the
> typical plastic tabs.
> If anyone has experience with this could you please share it.
> Thanks much,
> Dan


maxpower November 30th 04 10:29 PM

assuming that the oil pressure switch is not leaking and is still good, take
apart the connector and remove the rubber plug inside it and clean it out,
connect the connector back to the sending unit, that is basically all the
vent package is, if you are gonna go thru all that trouble you may as well
replace the sending unit, i think the part is about 30 bucks
"Dan Brenner" > wrote in message
om...
> I have read there is a TSB (08-36-99) on this problem that I have been
> experiencing lately. I have purchased the wire terminal/vent p/n
> 05017800AA mentioned in the TSB and I want to install it myself.
> I would like to know the location of the oil pressure switch on the
> 2.7L engine. I have looked under the engine (passenger's side) and I
> see 3 units. From the firewall towards the front of the car they a
> a black one, an orange one and a green one (these are the connectors'
> colors). I suspect the green one is the oil pressure switch but I'm
> not sure. If it is the one, how do I remove the switch connector from
> the switch? Something seems to lock it in place and I can't see the
> typical plastic tabs.
> If anyone has experience with this could you please share it.
> Thanks much,
> Dan




maxpower November 30th 04 10:29 PM

assuming that the oil pressure switch is not leaking and is still good, take
apart the connector and remove the rubber plug inside it and clean it out,
connect the connector back to the sending unit, that is basically all the
vent package is, if you are gonna go thru all that trouble you may as well
replace the sending unit, i think the part is about 30 bucks
"Dan Brenner" > wrote in message
om...
> I have read there is a TSB (08-36-99) on this problem that I have been
> experiencing lately. I have purchased the wire terminal/vent p/n
> 05017800AA mentioned in the TSB and I want to install it myself.
> I would like to know the location of the oil pressure switch on the
> 2.7L engine. I have looked under the engine (passenger's side) and I
> see 3 units. From the firewall towards the front of the car they a
> a black one, an orange one and a green one (these are the connectors'
> colors). I suspect the green one is the oil pressure switch but I'm
> not sure. If it is the one, how do I remove the switch connector from
> the switch? Something seems to lock it in place and I can't see the
> typical plastic tabs.
> If anyone has experience with this could you please share it.
> Thanks much,
> Dan




Mopar Steve March 9th 19 03:18 AM

98 Intrepid oil light flickers at idle when engine hot
 
replying to maxpower, Mopar Steve wrote:
Anybody know if this problem also occurred with the 3.5 L engine?

--
for full context, visit https://www.motorsforum.com/chrysler...hot-22977-.htm




All times are GMT +1. The time now is 11:56 AM.

Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
AutoBanter.com